Question about 1992 Honda Accord

1 Answer


Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 31 Answers

Code 15 is ignition signal output malfunction. main cause of this is a distributor, but it also can turn out to be an ecm or wiring.

Posted on Dec 12, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

What does the fault code P1336 TEC not learned mean

I have always done it with a scanner. You can try it without one. Start the car. In park, run the RPM's up to 3000 for about 15 to 30 seconds. Let it idle for about the same time. shut it off. You can disconnect the battery (for up to 30 minutes) to clear the light. Or use a code reader or scanner to turn it off. other wise it can take up to 50 key on and off cycles to turn the light off.

Apr 06, 2016 | Cars & Trucks

1 Answer

Car looses power, bogs down check engine flashes rapidly. No acceleration, then 15 - 30 seconds later power comes back and check engine light goes solid and stays on for 2 or 3 days.Anyone with idea?

You should read check engine code.
It tells you more than you can guess.
You can buy quality $1000 snap-on OBD scanner or $30 cheap one.
$30 will do good job. (you need to google after car tells you error code because cheap scanner shows only code but not meanings in plain English)

or you can visit local autozone and ask them read code for free.
unless you ask car itself, nobody will be accurate.

Dec 02, 2015 | 2003 Mazda Protege

1 Answer

I have been working on 3 nissan a 2000 sentra,2001 altima and a 2010 versa the code for the speed sencer comes up even after i put the new sencer in why is this

When any sensor is removed and replacer in a car, The computer has to relearn that the new sensor is working correctly. Sometimes it takes anywhere from 50-150 miles to do this depending on the car. You can also erase the code with a scanner tool, or by disconnecting the battery for 10-15 minutes. GOOD LUCK FRIEND.

Sep 25, 2014 | Cars & Trucks

1 Answer

How to clear service vehichle soon light no codes

You need to hook up a scanner to the car and clear the code. They make cheap one if you do not have one. You can try to remove the battery cables for about 15 minutes and see if that will reset it but most times you need a scanner to reset the trouble codes. Good Luck

Jun 28, 2014 | 2002 Chevrolet Monte Carlo

1 Answer

Tcc code 0073

The code you provided "should" has P1860 warming appear on the scanner.

P1860 + P0073 are the codes for Torque Converter Clutch solenoid problem.
Top off the ATF to max.
Drive the car for 15 minutes and re-scan.

Make sure you get all the codes.

Jan 16, 2014 | Cars & Trucks

1 Answer

How to reset the code on 740il 2001. Car will not crank

You would need a obd2 compatible scanner. You can try disconnecting the battery for 15-20 mins but I don't think that will help you. Did you check if you are getting power to the starter motor?

Oct 20, 2013 | BMW 7 Series Cars & Trucks

2 Answers

2007 Impala lt. Engine light came on today, tried the gas tanklid

These things happens sometimes. Disconnect your battery for 15 minutes then reconnect it. Just the ground cable is all needed to remove for this

Jan 12, 2010 | 2007 Chevrolet Impala LS Sedan New Cars

3 Answers

How do you clear the computer codes on a 1999 cadillac deville

Someone with a code reader can erase them, or take the battery cables for 15 min or so.

remember to disconnect the ground first and then the hot side,

If the code comes back then you still have that problem. No matter how long or how many times you clear it, if it comes back, you have to address the problem.

usually the left and right are as you are looking at the car. Driver, right, Passanger, left

Jun 13, 2009 | 1999 Cadillac DeVille

Not finding what you are looking for?
1992 Honda Accord Logo

Related Topics:

183 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts


Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides