Question about 2004 Jeep Grand Cherokee

1 Answer

Jeep starts and runs for about five seconds then cuts off

2004 jeep grand cherokee was attempted stolen. the ignition was ripped out.all parts were replaced including skim module. vehicle starts for about five seconds then shuts off.was told by dealer mechanic no additional programming was required.skim module is plug and play.HELP

Posted by on

  • Anonymous Mar 20, 2014

    how do I open column to reset the skim unit or replace it?

  • Anonymous Mar 24, 2014

    Replacing SKIM module in Grand Cherokee 2001 after attempted theft. Lock and housing and SKIM were smashed to bits. Have acquired another SKIM (used) and written the existing keys into the SKIM (via Eeprom). Wondering how the new skim is learned by the PCM.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 6,982 Answers

Obviously the dealer did not correctly complete the repair, therefore should be more involved in current problem. If your vehicle had any anti-theft device installed, be aware that many have delayed shut down features built in. I'd look there first, providing yo did not have any similar problem pryor to the theft.
Good luck!!

Posted on Dec 12, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why do my my 04 jeep cherokee runs for 3 seconds then shuts off?


sounds like the anti theft system is activated , proberly cuts the power to the fuel or ignition follow this link for reset procedure
How to Reset the Anti Theft on Jeep Cherokee eHow

Jul 15, 2014 | 2004 Jeep Grand Cherokee

1 Answer

I replaced the battery on a 2001 Jeep grand Cherokee and security is on so it wont start how do I reset computer to get it to start


Directly from the owners manual...
1.- Enter your car wth your ignition key and your theft remote, and press the Lock button on your remote five times in 10 seconds.
2.- Insert your key into the Jeep's ignition cylinder, and then turn the key to the "Run" position. Wait for the car's automatic chiming sound to stop before proceeding.
3.- Press and hold the Unlock button on your remote for around five seconds, and then press and hold the Panic button at the same time.
4.- Hold both buttons together for one second and then release. Wait for the car's chimes to sound again and then press and release the Lock and Unlock buttons on your remote.
5.- Press and release just the Unlock button on the remote next and wait for a chime again to indicate successful programming. You can then remove your ignition key to complete the resetting process.

Hope this helps; keep us updated.

Sep 28, 2011 | 2001 Jeep Grand Cherokee

2 Answers

Jeep was running fine. Shut it off for parking and it would not start. Jeep has 120k miles. Attempted to get computer call out for faults. Message was no ignition present. check computer cable. All other...


The ECM does control fuel delivery as well as fuel injectors. Unplug the cable from the ECM first and check for any corrosion. Spray with electrical contact spray and reset the plug firmly in the ECM.

Mar 20, 2011 | 1994 Jeep Grand Cherokee

1 Answer

1997 jeep grand cherokee limited with on board amp


try going through jcwhitney and possibly pioneer

Aug 04, 2009 | 1997 Jeep Grand Cherokee

2 Answers

1997 Jeep Grand Cherokee when start sometimes the


Most likely cause is the crankshaft sensor.

Jul 02, 2009 | 1998 Jeep Grand Cherokee

2 Answers

My 2004 Jeep Grand Cherokee limited power cuts out when I turn the ignition sometimes, I have checked fuse box under hood all ok, ckd battery, starter, alternator, all good, not sure what else.. is there a...


loosen up the ground cable at the body and on the block to where you can just move it and wiggle back and fourth then retighten also you will see a black wire comming off the positive of the battery unplug it and plug back in make sure it has a good connection. also seen bad factory terminals cut off and replace

May 16, 2009 | 2004 Jeep Grand Cherokee

1 Answer

Programm keyless entry


TRY THIS:
Sit inside the vehicle with all the doors closed.
Place ignition in the OFF position.
Open the driver's door. Leave Open.
Move the mechanical door lever to the LOCK position.
Turn the ignition to the RUN position.
Aim the transmitter at the Keyless Entry receiver and press Lock button.
Hold for five seconds until the door locks cycle.
Turn ignition OFF within 20 seconds

Good luck and hope this helps

May 07, 2009 | 1997 Jeep Grand Cherokee

2 Answers

Oxygen sensor wiring diagram


My 97 cherokee catalytic converter was stolen, oxygen sensor wires cut. the replacement is black, grey and white. the jeepicon1.png is different color. i need help knowing which wires get connected to which.

Jun 24, 2008 | 1997 Jeep Grand Cherokee

Not finding what you are looking for?
2004 Jeep Grand Cherokee Logo

Related Topics:

398 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...