Question about 2000 Toyota Land Cruiser

1 Answer

Red light with key emblem fashes

Hi, a red light with a key flashes when ignition key is removed on my 2000 landcruiser fx a it is set in same warning light as a/t oil temp. Thanks Mel

Posted by on

  • special_fx Dec 12, 2008

    Many Thanx Mel

  • special_fx Dec 12, 2008

    great stuff thanx again Mel

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 1,861 Answers

The red flashing "Key" indeicates that the factory security system is active. The light is a diode, and consumes very little battery power. The light alerts potential theives that the vehicle has an anti-theft system installed and active. Hoe this helps, and Thanks for choosing FixYa.

Posted on Dec 12, 2008

  • Toyota Ed Dec 12, 2008

    Thanks for the FIxYa; Much Appreciated!!! Glad to help!

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Red light Fashing on dashboard with key in it ,,any idea what it means


what kind of car do u have there are so many cars with red flashing lights with keys ,go on youtube but post your car

Feb 18, 2015 | Cars & Trucks

1 Answer

How to re-programme new car batteries in car key ?


1. Turn the ignition switch from Position 0 to ON 6 times within 10 seconds.
2. Then turn ignition switch to OFF position. Leave key in ignition switch.
3. After 2 seconds, the system will enter programming mode and will flash the warning lights twice.
4. Press and HOLD the unlock button on the Plip.
5. While pressing the unlock button, press the lock button 3 times.
6. Release the unlock button.
7. The warning lights will flash once to indicate successful programming.
8. Repeat procedure 4 to 7 for up to 4 plip key's.
9. When completed turn ignition ON, and the warning lights will flash 2 times.
10. Remove key, and check all plip key's for operation.
NOTE : The programming mode will stop when either the ignition is switch ON, 4 plip keys have been programmed or no input signal either from the switch or plip keys has been received for 120 seconds.

Nov 08, 2014 | Cars & Trucks

1 Answer

How to code new batteries in car key


1. Turn the ignition switch from Position 0 to ON 6 times within 10 seconds.
2. Then turn ignition switch to OFF position. Leave key in ignition switch.
3. After 2 seconds, the system will enter programming mode and will flash the warning lights twice.
4. Press and HOLD the unlock button on the Plip.
5. While pressing the unlock button, press the lock button 3 times.
6. Release the unlock button.
7. The warning lights will flash once to indicate successful programming.
8. Repeat procedure 4 to 7 for up to 4 plip key's.
9. When completed turn ignition ON, and the warning lights will flash 2 times.
10. Remove key, and check all plip key's for operation.
NOTE : The programming mode will stop when either the ignition is switch ON, 4 plip keys have been programmed or no input signal either from the switch or plip keys has been received for 120 seconds.

Nov 08, 2014 | 1999 Nissan Primera

1 Answer

Mk1 golf gti 1.8 oil red warning light comes on when engine is warm


You need to check for tow things first check oil level and its reapilty second you need to check oil volve and oil pump

Jan 16, 2013 | Cars & Trucks

1 Answer

New key programming for lancer 2005


you need to first install one of factory key into ignition.turn ignition switch on position for 5 seconds.switch off the ignition and remove key.wait 7 seconds insert new key into ignition switch.and switch ignition on until alarm system warning lamp will flash twice mean key programmed. switch ignition off if warning light illuminate for 3 seconds to confirm or flash 3 times indicate registration has failed. if you fail on programming new key let dealership reprogram new keys using diagnostic equipment.

Dec 20, 2012 | 2002 Mitsubishi Montero Sport

3 Answers

I had the oil changed but the change oil light is still on, how do i reset the computer? 2000 oldsmobile alero


How to Reset the Change Oil Light

After changing the engine oil, the system must be reset.

With the ignition key to ON, push the RESET button

located in the driver's side instrument panel fuse block. The

CHANGE OIL light will start to flash, press and hold the

RESET button again. The reset is complete when you hear
the chimes sound and the CHANGE OIL light goes out.

Oct 25, 2010 | 2000 Oldsmobile Alero

1 Answer

How to turn change oil light


iI you mean 'how to turn change oil light off" go to fuse panel. Open drivers door there is a panel cover on the side of dash board, remove cover there is a red RESET button that resets oil pressure and tire pressure. Turn the ignition key to the on position but don't start the car. Now press and release the reset button the change oil light should start to flash, now press and hold the reset button until you hear chimming hold until chimming stops then release, the change oil light should go off. If you need to reset tire pressure press reset button twice, the first push will make the change oil light flash the second press will make the tire pressure light flash then hold untill chimming stops, light should go out . Hope this helps.

Sep 30, 2010 | 2000 Pontiac Grand Am GT

2 Answers

VW Golf Mk4 1.4 16v Oil Light Warning on Dash


Measure your oil at normal operating temp, without the engine running of course. This will give you a more accurate reading once the oil has circulated in the system.

The system works like this:
  • With the ignition on, the oil pressure indicator light on the dash should come on and flash. Once the engine is started, the light should go out and stay out as long as the engine is running.
  • If the oil pressure drops below approximately 0.3 bar or 5 psi when the engine is running below 2000 rpm, the light will flash.
  • If the oil pressure drops below approximately 1.8 bar or 27 psi when the engine is running above 2000 rpm for more than 3 seconds, the indicator light will flash and the buzzer will sound.
If either this two warnings occur:
  • The engine should be switched off immediately and the oil level should be checked.

Apr 29, 2010 | 1999 Volkswagen Golf

1 Answer

Reset the oil light after changing the oil


There is a red OIL-R button inside the fuse pannel located next to the battery. remove the cover and turn the key to the RUN position; press and hold the reset button for 5 seconds. The Change Oil Soon light on the dash will flash to confirm the reset then go off. Turn key back off and you are all set.

Apr 06, 2010 | 2000 Saturn SL

1 Answer

Flashing alarm light after battery change. Car wont start,


System operation
System arms 5 seconds after switching ignition OFF. Switch ignition ON. Ensure clock LED illuminates for 3-5 seconds. If LED flashes rapidly at regular intervals for approximately 1 minute, then flashes at irregular intervals: Key code not recognised. Remove key and try again.
Programming
When
System malfunction: LED illuminates for 1 minute, then flashes at irregular intervals. Key(s) added or replaced.
NOTE: Replacement keys MUST have blue mark. Keys with red mark are NOT compatible with this system.
How
NOTE: Programming method using vehicle keys can be deactivated using diagnostic equipment.
Obtain 2 programmed keys (A and B). Insert key A into ignition switch. Turn ignition switch to position II. Wait 1 second. Switch ignition OFF. Remove key A. Insert key B into ignition switch within 5 seconds. Turn ignition switch to position II. Wait 1 second. Switch ignition OFF. Remove key B. Within 10 seconds: Insert key to be programmed into ignition switch. Turn ignition switch to position II. Wait 4 seconds. Switch ignition OFF. Wait 5 seconds. Start engine. If engine does not start and clock LED flashes: Switch ignition ON. Wait at least 20 seconds. Switch ignition OFF. Repeat programming procedure. Repeat above procedure to program remaining keys. Keys can also be programmed using diagnostic equipment

Mar 08, 2010 | 2000 Ford Focus

Not finding what you are looking for?
2000 Toyota Land Cruiser Logo

958 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

74241 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22082 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7207 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...