Question about 1995 Dodge Ram 2500

1 Answer

I would like to turn up my fuel injectors how do i do it

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 39 Answers

Reprogram the ECM with an aftermarket tool made by hypertech

Posted on Dec 11, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

No fuel in one cylinder 1998 ford ranger


Either has a bad injector or the wiring to that particular injector has been pinched or skinned and grounded somewhere.

Feb 20, 2015 | 1998 Ford Ranger

2 Answers

Car is turning over but not getting fuel ideas anyone thanks


There is not much information for a good answer.
  1. Fuel filter clogged
  2. fuel pump not working [fuse,bad pump,broken wire etc]
  3. computer not telling the pump or injectors to work [should set a code]
  4. dirty injectors

Feb 09, 2015 | Cars & Trucks

1 Answer

1986 Corolla GT-S Fuel Injectors Not Firing


Here's how to check the injector circuit.
Pull off one injector connector and with a testlight grounded on the engine, turn key to on. Probe the terminals of the injector connector. One of the terminals should have steady power from the ignition being on. If neither terminal turns on the testlight, the injector drive circuit is not working. There may be a fuse for the injectors out. Also check the efi fuse, located I think under the hood. If still no good, you will have to check the circuit from the ignition switch to the injectors.
If you got a steady light from one terminal, the drive circuit is good. Now check the ground circuit: Put the lead of the testlight on the positive battery post, and put the probe of the testlight into the injector terminal that did not light up.Someone will have to crank the car over for you. If the testlight is blinking when the car is being cranked, the injector circuit is working right. The blinking light means the computer is properly grounding the injector circuit to fire the injectors. The ground circuit leads direcdtly from the injectors to the computer. When the computer internally grounds that injector, the injector will pulse, or fire. Good luck, and I hope you find the problem.

Mar 29, 2012 | Toyota Corolla Cars & Trucks

1 Answer

I have a fault 296 on my golf tdi 2008 can you please tell me a little about the fault please.


296 is not a valid code, I will assume it is a P0296, if that is not the case let me know.
Code P0296 is triggered when the Power Train Control Module (PCM) detects that the acceleration rate of the crankshaft for Cylinder #12 was less than a calibrated amount. During normal conditions the PCM turns the Fuel Injectors ON and OFF in the Fuel Injection System. SymptomsPossible sumptoms of OBD code P0296
- Engine Light ON (or Service Engine Soon Warning Light) - Engine Misfire - Engine Run Rough - Low MPG CausesPossible causes of OBD code P0296
- Fuel Injector #12 - Faulty or Corroded Fuel Injector #12 Connector - Plugged #12 Fuel Injector - Dirty #12 Fuel Injector Possible Solutions- Clean Fuel Injector #12 Connector - Clean Fuel Injector #12 - Replaced Fuel Injector

Feb 02, 2012 | 2008 Volkswagen Golf 1.6

1 Answer

What causes injector not firing gas?


FUEL INJECTOR NOT FIRING COULD BE FAULTY FUEL INJECTOR.HOOK A NOID TEST LIGHT TO FUEL INJECTOR ELECTRICAL CONNECTOR. CRANK THE ENGINE WATCH THE NOID TEST LIGHT SHOULD BE BLINKING WHILE ENGINE TURN OVER.IF TEST NOID LIGHT STEADY PCM FAULTY NOT FIRING THE FUEL INJECTOR.IF FUEL INJECTOR DONT BLINK OR LIGHT UP.YOU HAVE OPEN WIRING CIRCUIT TO THE FUEL INJECTOR CONNECTOR.

May 13, 2011 | 1990 Geo Tracker

2 Answers

My golf 1.9 tdi is miss-firing


Check the fuel lines, fuel filter, what is the mileage? If it is high than it might a sign of injector pump or injectors.

Apr 08, 2010 | 2002 Volkswagen Golf

1 Answer

How toreplace fuel injector chevy astro 1999


Removal & Installation

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Relieve the fuel system pressure. Refer to the fuel system relief procedure in this section.
  3. Remove engine cover.
  4. Disconnect negative battery cable.
  5. Remove upper manifold assembly.
  6. Disconnect fuel meter body electrical connection and the fuel feed and return hoses from the engine fuel pipes.
  7. Remove poppet nozzle out of the casting socket by squeezing the nozzle locking tabs together.
  8. Remove fuel meter body by releasing the locktabs.
    NOTE Each injector is calibrated. When replacing the fuel injectors, be sure to replace it with the correct injector.
  9. Remove lower hold-down plate and nuts.
  10. While pulling the poppet nozzle tube downward, push with a small prytool down between the injector terminals and remove the injectors.

    0996b43f8022cb96.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Exploded view of the fuel meter assembly, including the injectors

To install:
  1. Lubricate the new injector O-ring seats with engine oil.
  2. Install o-rings on the injector.
  3. Install fuel injector into the fuel meter body injector socket.
  4. Install lower hold-down plate and nuts. Torque the nuts to 27 inch lbs. (3 Nm).
  5. Install fuel meter body assembly into the intake manifold. Torque the fuel meter bracket retainer bolts to 88 inch. lbs. (10 Nm).
    CAUTION To reduce the risk of fire or injury ensure that the poppet nozzles are properly seated and locked in their casting sockets.
  6. Install fuel meter body into the bracket and lock all the tabs in place.
  7. Install poppet nozzles into the casting sockets.
  8. Engage electrical connections.
  9. Install new o-ring seals on the fuel return and feed hoses.
  10. Connect fuel feed and return hoses and tighten the fuel pipe nuts to 22 ft. lbs. (30 Nm).
  11. Connect negative battery cable.
  12. Turn the ignition ON for 2 seconds and then turn it OFF for 10 seconds. Again turn the ignition ON and check for leaks.
  13. Install the engine cover.

Jan 20, 2010 | 1999 Chevrolet Astro

1 Answer

Trouble shooting


sound like flooding caused by dirty clogged fuel injectors.the injectors by being clogged and dirty.when you turn off car the injectors will leak causing plugs to foul out. go buy a bottle of fuel injector cleaner.go to gas station fill up gas tank.then pour a bottle of injector cleaner in gas tank.drive car around to allow injector cleaner clean out fuel injectors.

Dec 03, 2009 | 1999 Oldsmobile Alero

2 Answers

Fuel injecter fuse blow imeditaly when ignition turn on


sounds like a short in the wiring from the fuse and the fuel injector junction block. GM like most fuel injection systems control injector firing by the computer providing ground to each injector in pairs or individually. The fuel injector fuse provides power to the injectors using splices therefore enabling one wire to feed 6 injectors. A shorted wire at any of these wires will blow the fuse. On one rare incident I found a faulty computer caused the fuse to blow. A shorted injector will just cause a rough running problem due to the injector stuck either open or closed.

Aug 05, 2009 | 1991 Chevrolet C2500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

58 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...