Question about 1999 Dodge Ram

1 Answer

Dodge ram 2500 diesel control arm bushings

How do you change them?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 133 Answers

You replace the arm. maybe go with a set of adjustable aftermarket ones

Posted on Jan 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i change my rubber bushings on the front suspention of my 1997 dodge ram 1500


opper Control Arm Bushings
  • To access the upper control arm, remove the shock absorber and the strut bar. Also, disconnect the sway bar from the lower control arm, if your particular Ram model is equipped with it. After that, you can hold the coil spring in place with a spring compressor.
    Secure the wheel hub assembly to the chassis using a wire before you disconnect the upper ball joint. This will prevent damage to the brake hose. When ready, release the ball joint using a ball-stud loosening tool (see Resources).
    The upper control arm mounts to the chassis with a cam bolt assembly. Once removed, you can place the control arm on a vise and remove the bushings using a bushing service tool (see Resources). When installing the new bushings, do not use any lubricant but make sure the flange on the bushing end seats properly on the arm bore. Then re-install the upper control arm. When finished, take your Dodge vehicle to a good shop to align the front suspension.
Lower Control Arm Bushings
  • Remove the shock absorber and strut bar. If your particular model is equipped with a sway bar, disconnect it from the lower control arm.
    Secure the coil spring with a spring compressor and release the lower ball joint from the wheel/hub assembly using a ball stud loosening tool (see Resources).
    Now you can release the lower control arm by removing the rear mounting bolts. Remove the bushings with a bushing service tool (see Resources). When installing the new bushings, do not use lubricant and make sure they seat properly on the control arm bore. Then replace the lower control arm. When finished, take your Dodge vehicle to a good shop to align the front suspension

Oct 20, 2011 | Cars & Trucks

1 Answer

What is the rocker arm tourqe specs on my 2005 dodge ram 5.9 l diesel


Hi.. The Rocker arm should be torqued to 36 N.m ( 27 Ft lbs)
I hope this help on your question. Thank you for use fixya

Aug 17, 2010 | 2005 Dodge Ram 2500 Truck

1 Answer

I have a 2006 Ram 2500 Diesel. My heater quit working. One minute it was blowing hot air, then next it was blowing cold air. Any ideas what this is or how to find out without spending an arm and a leg?


low coolant. disconnected or faulty servo to control difference between hot and cold or the heater core could be clogged. if it warms up when reving the engine then it is probably low coolant.

Jan 20, 2010 | 2006 Dodge Ram 2500

1 Answer

I have a 2006 Dodge Ram 2500 Diesel (no owners


I don't have a owners maual either but I beleive its 10 liters.Use 15w40 ams oil with ams oil filter.7500-10000 miles for filter changes and 20000 miles between oil changes

Sep 24, 2009 | 2006 Dodge Ram 2500

1 Answer

2006 dodge ram 2500 4x4 diesel replace brake pads front and back


Straight forward job. Remove wheels, remove 2 caliper bolts per wheel, check bolts,and bushings for wear/corrosion and lubricate, remove calipers, remove brake pads, push caliper pistons into calipers, replace anti-rattle clips, put new pads in, put caliper and bolts in, put wheels on. Start truck and press brake pedal several times to take up slack and you're done.

Apr 25, 2009 | 2004 Dodge Ram 2500

1 Answer

2003 Dodge Ram 2500 diesel 4x4 wiring diagram


TPIM PROBLEM , MUST HAVE COMPUTER FLASHED AT DEALERSHIP

Apr 21, 2009 | 2001 Dodge Ram 2500 Truck

2 Answers

1999 Dodge Ram 2500 Diesel 4x4


there is a cruise control module , easiest way to find it is follow 2nd throttle cable under hood right to it. it most cases there unplugged

Jan 08, 2009 | 1999 Dodge Ram

1 Answer

Need control arms for 1997 2500 RAM 4x4 Diesel


new: www.rockauto.com
used: www.car-parts.com

Dec 18, 2008 | 1999 Dodge Ram 2500 4WD

Not finding what you are looking for?
1999 Dodge Ram Logo

Related Topics:

204 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...