Question about 1992 Mazda Protege

2 Answers

Removal of left rear door panel on a 92 protege

My car doesn't have power windows so how do i get the door panel around the crank?

Posted by on

  • bad_dog1
    bad_dog1 Dec 11, 2008

    i don't see how i get any clips without breaking off my door panel

×

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 99 Answers

Hi depending on the type there is 2 ways here.

Is there a cap on the front of the window crank if so take it off and behind it there is a screw undo it and remove crank

2 there is a clip behind the crank use a small screw driver or long nose pliers wich ever suits you best its a bit fiddly but be patient with it, TIP.. when putting the crank back on put the clip on the crank first then just slide it back on.

Hope this helps
Regards
Steve

Posted on Dec 11, 2008

  • usersteve83 Dec 11, 2008

    Its just behind the window winder very small gap but it is there, bit of a fiddly job im afraid

×

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 160 Answers

There is a clip on the inside of the crank

Posted on Dec 11, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Remove citroen c3 rear door panel


Check out how the door panels are attached to the car. Most panels use screws and bolts but others have snap-in fittings. Gather all the tools you need for removing the door panels. If the panel is attached with screws and bolts, you need a screwdriver or ratchet and socket. Car door panels with snap-in fittings are easily removed with a flathead screwdriver.
Locate where the screws and bolts are before starting. These are usually found in the arm rest area, along the bottom or sometimes near the door lights.
Roll down the car door window. Begin removing all screws and bolts that hold the door panel onto the car. If your car has snap-in fittings, pry gently on the bottom corner of the door panel until the fittings pop out.
Remove the power window control panel if your car has power windows. The control panel should pry out easily, and then you unplug the wiring harness from the back and place it to the side.
Use an L pick and flashlight when locating a manual window crank. Look behind the window crank and slide the pick under the edge of the metal clip that holds the crank in place. Remove the clip and pull the crank off.
Remove the door handle by unscrewing the small screw located in the center. Gently pull the door handle out until you see the back of the handle and unclip the rod from the door handle. This should remove the handle unless the handle and door lock are attached, then you just unclip the rod from the lock and remove them both together.
Unscrew the cap off rear upper corner door panel locks. These don't have a rod attaching them to the handle and unscrew separately from the door handle.
Pop the door panel off after you've removed everything. Gently pry on the bottom edge of the door panel until it releases. Pull out and up to completely remove the door panel.
GM Tech2 GM Diagnostic Scanner with 32MB Card and TIS2000

Oct 10, 2014 | 2006 Citroen C3 1.4i

1 Answer

How do I remove the inside door trim on a Mazda 2003 Protege so I can replace the exterior left hand rear view mirror?


Usually you have to remove all the handles etc. from the inside. (The screws are covered with plastic plugs or similar.) Then the trimming is held by plastic or metal clips around the edges. Carefully pry the interior off and gain access behind.

Jul 14, 2010 | 2003 Mazda Protege

1 Answer

How do you remove the inside rear door panel of a 2002 ford explorer. I need to service the power window on the rear door on the passenger side. Submitted on 9/29/2009 @ 1:07 pm. Thank you


1. Open window & remove door lock knob. 2. Remove 2 screws from armrest & remove armrest. 3. If manual windows, remove windoe crank. 4. Pry under & remove trim panel around door handle, remove any un-covered screws. 5. This is the fun part, the door panel is affixed with plastic retaining clips, slip something thin under door panel until you can feel where clip is and pull door panel away from door at that point. These clips are suppose to remain in the door panel, but rarely do. They usually remain in the door itself. do this for EVERY clip you find, there are clips approx a foot apart around the entire panel. Good luck. 6. After all retaining clips are pulled out, lift panel slightly to disengage panel from flange at base of window. 7. Disconnect any electric wires or switches and there you have it. Try not to curse.

Sep 29, 2009 | 2002 Ford Explorer

1 Answer

Need to remove left rear door panel


  1. If equipped, remove the window crank handle by using a retaining clip removal tool.
  2. Remove the door handle bezel by inserting a flat trim removal tool between the door panel and handle bezel to release the locking tabs.
  3. Remove all door panel electrical connectors .
  4. Remove the door panel push pins and trim screws. Lift the door panel up and out to release the door panel locking tabs.

May 22, 2009 | 2006 Chevrolet Silverado

1 Answer

Inside door handle doesn't work (removing the driver side panel)


If you have power windows start by disconnecting your negative battery cable. Then you need to locate and remove the screws that hold your door handles in place (they may be hidden by snap in, or snap on clips). Once you remove the screws that hold the door handles, remove any wire connectors to the handles, if they're not power you will need a small hook (kinda like a knitting needle) to remove the window crank. A manual window crank is held in place by a clip on the base. Slide the hook behind the base and remove the clip. The door panel itself, is held on by snap in clips, and you will need a small pry bar to pull them from the door (try to gat as close to, or directly under the clips to prevent them from tearing out of the door panel). Once the clips are removed from the door, pull the panel upward to remove it from the door.

Install in reverse.

I hope this helps you, and I wish you luck on your repair.

May 04, 2009 | 1992 Chrysler New Yorker

1 Answer

1995 toyota celica


With the year of the car, the electric motors for the windows are weakening. the rubber seals on the windows have so much hold on the window, that a weak motor will not have enough power and thus will need to be replaced. You can remove the door panels, by removing all the screws, take flathead screwdriver and lighly pry around panel, pull up and remove panel. Then remove inside plastic and you will have access to the window motors.

Apr 30, 2009 | Toyota Celica Cars & Trucks

1 Answer

'88 toyota camry rear window stuck in down position


To get to the Window:

Remove Door Inside Handle:
remove screw, slide the handle forward.
Disconnect the control link and remove the handle.

Remove Door Trim with Inner WeatherStrip:
Remove the two screws from the armrest.
Insert a screwdriver between the trim retainers and the door panel to pry it loose.  Eight hidden fasteners. 1 top left side of door.
1 right side about same height as top of armrest. 1 (each side) about same height as bottom of armrest. 1 on each corner bottom. 1 bottom in middle.  1 on left side between bottom corner and the previous at about lower armrest height...

Remove Service Hole cover.
Remove Door Glass Run.

Remove Division Bar (upper window section divider):
Remove the two screws under the weatherstrip
Remove the bolt.
Pull out the division bar.

Remove the Window Glass:
Place the glass in the door cavity.
Remove the two glass channel mounting bolts.
Remove the window glass by pulling it upwards.

You now have access to the Power Window Regulator; possible replacement of motor etc.

What type of 'things' have you tried for fixing the window and restoring operation?

Jan 22, 2009 | 1988 Toyota Camry

1 Answer

97 VW Jetta right rear power window off track


There should be six or seven allen wrench screws around the edge of the door panels. Loosening these releases the retaining clips inside. You will then want to remove the manual window crank if you have one by laying two fingers flat on the door panel and pushing the ring around the base of the crank sideways. You might have to rotate around this as it only pushes one way. Next you will have to remove the two large golden screws directly under the door panels handle. If you have rear door panel speakers you will have to politely pry off the speaker grill with a flat blade screwdriver and remove the speakers four screws and the wire clip from behind the speaker. You will also have to unscrew the door lock post. Then you should be able to lift the door panel up to release the top lip of it from the door.

Dec 29, 2008 | 1997 Volkswagen Jetta

1 Answer

Want to replace left power mirror on a 2004 ford ranger. Not sure


unscrew 2 screws in black plastic handle, remove black plastic but do not unplug if electric windows look in lower rear corner remover one screw there and one screw behind the black plastic handle and if hand crank windows pull not to hard and separate window crank and find a phillips or torx screw in the but have window down and gentle get fingers on lower sind of door panel and slide upwards towards the sky and it shoud come off

Dec 11, 2008 | 2004 Ford Ranger

1 Answer

REAR DRIVER'S SIDE DOOR PANEL


There are most likely a couple of screws mabye hidden under a little plug or plastic cover around the door handle and on the under side of the panel.Then if it is a crank style window you will have to remove the window crank handle,after that there are plastic panle pop clips you will just have to pull on panle and they should pop out,then lift the panle up off the window door seal.

Aug 30, 2008 | 2004 Pontiac Grand Prix

Not finding what you are looking for?
1992 Mazda Protege Logo

154 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

64034 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...