Question about 2002 Isuzu Rodeo

1 Answer

Cant get the timing right on my 2002 4 cyl 2.2 L rodeo

Was getting hot so replaced the water pump and timing belt although the old ones checked out fine when taking out but still replace both of them with new ones, now wont start , I swear its all lined up right what is going on any suggestions will be greatly appreciated.

Posted by on

  • yadayada
    yadayada May 11, 2010

    IT IS NOT LINED UP, ( WISH I HAD A DOLLAR FOR EVERY ONE THAT CAME INTO THE SHOP THAT RAN BAD AND CUSTOMER HAD DONE BELT WRONG) RECHECK IT, ALMOST WON'T DO ON TIMING BELT ISSUES LIKE THIS ONE.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 99 Answers

Hi just a tooth out on the timing will cause problems always check and check again it HAS to be perfect, also if you started this as it was over heating and the pump was ok check radiator and have the cylinder head pressure tested to rule out a head gasket problem, Hope this helps

Posted on Dec 11, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Toyota Camry 1993 4 cyl water pump failing, have removed thermostat, considering Electric inline pump as replacement as option ? Please advise me of pro's and con's.


i owned the 1995 4 cyl wide body camry till the cooling system failed in heavy traffic and over heat stripped out the head bolt threads in the block

the toyota camry engine designation is a 5S-FE

water pump is driven by timing belt
behind timing belt covers
they have to be removed to get to the water pump

normally timing belt, seals ,tension er pully and water pump are replaced at the same time ..comes in a kit

i dont have the 5S-FE cooling system hot under pressure specs

so I cant answer which inline electric pump pressure is required to work on the 5S-FE


engine repair manual free download pdf
5S-FE 431 pages
http://www.turboninjas.com/camry/eg1.pdf
ENGINE MECHANICAL to page 144
EMISSION CONTROL SYSTEMS
MFI/SFI SYSTEM page 164
COOLING SYSTEM page 238
LUBRICATION SYSTEM page 268
DIAGNOSIS SYSTEM page 296
CIRCUIT INSPECTION page 336
water pump as a part

timing belt water pump kit
water pump
,location on the engine with timing covers removed


e7622159-98af-4a83-8989-bd6dd48bcde3.jpg26279563-dp42dlzfhn4dbdhi1rc14q4e-1-2.jpg26279563-dp42dlzfhn4dbdhi1rc14q4e-1-3.jpg

Sep 10, 2016 | 1993 Toyota Camry

1 Answer

Is the 2002 hyaundai santefe a zero tolerance motor


The 2002 Santa Fe 4 cyl and 6 cyl engines are deemed "Interference" engines. If the timing belt should break or slip a few teeth, the pistons will strike the valves and most likely destroy the engine. Thus it is very important to change the timing belt every 80,000 - 100,000 miles (along with a replacement water pump). I recommend buying a belt/pump kit and having a local independent shop do the install (much cheaper than a dealer's $600 charge!).

Belt & pump kits are available via Amazon:
http://tinyurl.com/lqsqpwo

Starting in 207 Hyundai started shifting all of their engines to metal timing "chains"... more or less eliminating the possibility of such a problem. However, water pumps still go out... but not nearly as often or catastrophic a problem!
25592558-5eold4ui3lytmz02r5ph1yca-5-0.jpg

Mar 19, 2015 | 2002 Hyundai Santa Fe

1 Answer

Bent valves cyl 4 & 6 on a 94 isuzu rodeo v6, do i need to pull the engine inorder to repair?


One way or another you have to get the head off to replace the valves. You may have cracked the head by the valves being bent.

Jan 19, 2013 | 1994 Isuzu Rodeo

1 Answer

Water pump and timing belt replacement


confirm you timing belt marking at the engine before you start the work. then dismantle all the belt one by one until you reach the timing cover. mark the timing mark again. then start dismantle the timing belt set. after all the belt are out, open the water pump and start to put back the new part by using reverse order from the opening list. make sure the timing marking are the same as you check at the first time. before you start the engine, make sure you turn the engine 2 or 3 round and make sure no part are hitting. good luck.

Nov 19, 2010 | 2002 Isuzu Rodeo

1 Answer

My mechanic is telling me that it's necessary to replace the water pump on my 2002 Isuzu Rodeo when replacing the serpentine belt. Is this true? Ball park figure, how much would it be to replace both?


BS. Water pump should be replaced with the TIMING BELT. The serpentine belt doesnt even touch the water pump. If you have a V6 that is. but you didnt say what engine you have.

Nov 12, 2010 | 2002 Isuzu Rodeo

2 Answers

Is it necessary to take the timming belt off to replace the water pump on a 1996 isuzu rodeo


3.2L engine, you will have to remove timing belt to replace water pump, your water pump is timing belt driven, I would replace timing belt while in there, good luck, hope this was very helpful.

May 14, 2010 | 1996 Isuzu Rodeo

1 Answer

My 2002 Buick Rendevous has a hot coolant


Install the new thermostat (make sure it is the right temp). This will allow for your coolant to stay long enough in the radiator to cool down.

If that does not fix it, check radiator cap, belt that turns the water pump and the water pump itself along with its pulley.

There is also the possibility that the coolant temperature sensor is giving off false readings, that the coolant system is clogged or your engine fan is not operating when it should be.

May 03, 2010 | 2002 Buick Rendezvous

1 Answer

Water pump replacement 96 isuzu rodeo


Remove belt, fan, fan shroud and fan bracket. Remove timing covers, timing belt and water pump. Replace timing belt and the hydraulic tensioner with new ones. I suggest you get a mechanic to do this as you can easly get it out of time. Not an easy job.

Jul 03, 2009 | 1996 Isuzu Rodeo

1 Answer

2002 Izusu Rodeo timing problems


Check with your local Izuzu dealer, there is a procedure to set the cams in proper relationship with each other. This involves turning the cams up to 8 rotations to have them "jump" into the proper spot. I have had the same problem and found a bulletin that shows the correct way to time the engine.

Dec 11, 2008 | 2002 Isuzu Rodeo

1 Answer

98 4 cyl isuzu rodeo timing belt


I looked in my database but can't help with that one.

Nov 20, 2008 | 2001 Isuzu Rodeo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

137 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...