Question about 1993 Nissan Quest

1 Answer

1993 mercury villager-nissan quest- FRONT LEFT BRAKE

I HAVE REPLACED CALIPER ABS BOX AND STILL HAVE A VERY STICKY BRAKE

Posted by on

  • Anonymous Mar 16, 2014

    how to adjust throttle body on a 1993 mercury villager

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 98 Answers

Master cylinder.

Posted on Dec 11, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1999 mercury villager front drivers side brake caliber locks up replaced caliper and rotor already


Could be collapsed rubber brake hose on drivers front brake. Inside of hose has collapsed like a flap gate and brake fluid can not return to master.

Apr 24, 2015 | 1999 Mercury Villager

2 Answers

Left front caliper sticks on 93 villager after replacing caliper, rotor and brake hose


If the caliper is sticking it should have a warranty. Either installed incorrectly or it was bad out of the box. Remove and replace.

Oct 21, 2010 | 1993 Mercury Villager

2 Answers

2001 brake pad replacement 2001 nissan quest


The hard part is pressing the caliper piston abck into the caliper so you can get the new, thicker pads over the rotor. A large C Clamp works best.

SECTION 206-03: Front Disc Brake 2001 Villager Workshop Manual
REMOVAL AND INSTALLATION Pads —Front Disc Brake Removal
  1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. Remove the front disc brake caliper bolts. torx bit. T20?
  1. Support the front disc brake caliper from the front strut and spring assembly using mechanics wire.
  1. Remove the front disc brake pads.
    1. Remove the outboard front disc brake pad.
    1. Remove the inboard front disc brake pad.
Installation
  1. s1v~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Make sure the master cylinder reservoir does not overfill and spill brake fluid while retracting the front disc brake caliper piston.
    NOTE: It is necessary to fully retract the front disc brake caliper piston in the bore before installing the front disc brake pads.
    Install the front disc brake pads.
    1. Install the inboard front disc brake pad.
    1. Install the outboard front disc brake pad.
Caution. The outer pads are left and right. put left on driver side.
  1. Position the front disc brake caliper on the front-wheel knuckle and install the brake caliper pin bolts.
  1. s1v~us~en~file=ani_caut.gif~gen~ref.gif WARNING: It is necessary to depress the brake pedal several times to position the front disc brake caliper piston before driving the vehicle.

Apr 23, 2009 | 2001 Nissan Quest

1 Answer

Mercury villager brakes drag when driving


replace the flexible hoses, they are collapsing inside, preventing fluid from returning to reservoir.

go to this site for villager hep

http://autos.groups.yahoo.com/group/villagerquest/

Apr 06, 2009 | 1993 Mercury Villager

3 Answers

Front brakes lock up


I have a 2000 Mercury Villager doing the same thing Lf wheel drags after it gets hot, problem was abs modulator, after I replaced Lf caliper, brake hose etc it still was dragging abs modulator has filters in it that get clogged and will not release.

Aug 24, 2008 | 1994 Nissan Quest

Not finding what you are looking for?
1993 Nissan Quest Logo

Related Topics:

204 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...