Question about 1996 Isuzu Hombre

2 Answers

Crankshaft position sensor on a 1996 isuzu hombre

Where is the sensor located?

Posted by on

  • Roger Carvajal Dec 14, 2008

    The isuzu hombre is a 4 cyl and the sensor is located next to the ignition coil packs. all motors are not the same

  • Matt Koch
    Matt Koch Dec 07, 2013

    How do you get it out


2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 98 Answers

Should be between the crank dampener and the block, i mean they are all relatively the same on all cars should be the only wires running close to the crank dampener

Posted on Dec 11, 2008

  • erik mcdonald
    erik mcdonald Dec 14, 2008

    why would you rate this is inapropriate?

  • salcedoautbe
    salcedoautbe Nov 03, 2012

    on the 2.2 the crankshaft censor is under the coil packs on the passenger. It's has a 10mm nut with a thread sticking out the top of it. Not to be confused with the two censors in front of the coil pack which are camshaft censors


  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have and isuzu hombre 1998 i ran it into an ocean .it just start for only 3 second and shut off cannot keep running longer then that

Posted on May 28, 2009

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Location or diagram Oil sending unit 98 isuzu hombre

what engine, THE CAR IS A GM s10 IN DRAG.
4.3L v6 Vortec 4300, GM
2.2l i-4, OHV ENGINE. NOT ISUZU!!!

In 1996, Isuzu replaced its Pick Up with a version of the Louisiana-built Chevrolet S-10, the Isuzu Hombre, based on the Brazilian market S-10
so google the vortec 4300
here Ill type for you....

on most v6, its near the oil gallery , on a bank.
so that means if youd look on both banks , the one with the 1 wire sensor is it.
but not this v6
its here.
log in to mitchell's and read, its all there.


Nov 22, 2016 | 1998 Isuzu Hombre

2 Answers

Where is the cold start valve or injector located on a 1998 isuzu hombre pickup?

Check for spark to the plugs. If you don't have it, look at the crankshaft position sensor. If you do, then look at replacing the fuel filter. Clogged filters will give you pressure. But not volume. I would replace it anyway.

Dec 08, 2014 | Isuzu Cars & Trucks

1 Answer

Crankshaft position sensor

Spray sensor at the block due to o-ring being dry and it is binding. After spraying it rotate sensor gently and work it in and out and rock it back and forth and keep spraying it with lube. It WILL take some time. Once removed lube the new one with anti-seize very well. Let me kniow if I can be of any further assistance.

Dec 07, 2013 | 1996 Isuzu Hombre

1 Answer

Turns over but won't start

change the crankshaft position sensor thats whats wrong with it.

Jan 27, 2013 | 1997 Isuzu Hombre

1 Answer

Locate and repair of a 1998 isuzu hombre throttle sensor

The throttle position sensor is normally not repairable but is replaced as an item.
If you are unable to locate or recognize the sensor, you might want to consider spending $20 US for a service manual for your Isuzu:
Isuzu Hombre manual

Mar 07, 2011 | 1998 Isuzu Hombre

1 Answer

Changed crankshaft 1996 Isuzu hombre and leaks oil now

u might have dammaged the seal around the crank shaft or damaged the gasket but first check bolts are tightend to manufactures specifications

Oct 22, 2010 | 1996 Isuzu Hombre

1 Answer

Where is the distribtor?

you have a DIS (direct ignition system) it consists of a coil pack,ignition module,crankshaft position sensor and ECM. there is 2 on your vehicle. if you have no spark check your crank sensor or ignition module. or goto local auto store and get a spark check for 5 bucks which plugs inline of the plug wires either at the coil or plugs.hope this helps

Jul 13, 2010 | 1996 Isuzu Hombre

1 Answer

My 97 Hombre with 2.2 L 4 cyl, all of a sudden

probably the throttle position sensor,but also could have jumped time.i would take the T.P.S. out and check the resistance,i am not sure what the correct resistance is for that model but you can find out at the parts store.

Nov 21, 2009 | 1996 Isuzu Hombre

1 Answer

1996 hombre won't start

could be your ignition coil modules, or/and the crankshaft position sensor...

Aug 09, 2008 | 1996 Isuzu Hombre

Not finding what you are looking for?
1996 Isuzu Hombre Logo

553 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts


Level 3 Expert

69014 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22026 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides