Question about 1991 Toyota 4Runner

1 Answer

Rear Tail Light

How do I remove the rear tail light, passenger side, to replace a cracked cover?

Posted by on

  • Anonymous Mar 19, 2014

    How to replace rear light cluster

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Toyota Master
  • 2,007 Answers

Bolts will be on the inside of your vehicle.

Posted on Apr 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Remove near side rear lights cover how do I do this


The rear side lights are held in place by screw/bolts that are accessed by opening the rear tail gate. They are on the inside near the edge. Usually a black 10mm bolt with a Philips "+" head. There are 2. Remove the and the light will come out as the full assembly. The cover is part of the light assemble and not be replaced.If it is cracked or broken the whole lamp assembly will need the be replaced.

j

Sep 25, 2014 | 2004 Toyota Yaris

1 Answer

HOW TO REMOVE PASSENGER SIDE REAR TAIL LIGHT


From inside the trunk remove the cover on either side & you will have access to the holdown bolts for the taillights (behind the lens)

Sep 10, 2014 | 2008 Buick Lucerne CXL

1 Answer

Replace rear side marker light


I had this message sent to me to solve....THIS IS MY QUESTION THAT I ASKED....LOL....SINCE THEN; I'VE BEEN INFORMED THAT YOU HAVE TO GO THROUGH THE OUTSIDE TAIL-LIGHTS TO GET TO THE MARKERS
DOES ANYONE ELSE KNOW ANOTHER WAY?
I have stainless steel covers over my tail-lights and will have to remove the "adhesive" on the covers to remove the tail-lights...HELP!

Jul 05, 2014 | 2007 Chevrolet Corvette Convertible

1 Answer

How do I replace 2004 Pontiac Vibe passenger side tail light assembly?


Hello Tim.

Here is the procedure.
  1. Open the rear compartment lid.
  2. Remove the rear compartment trim panel (4).
  3. Remove the tail lamp socket (2) from the tail lamp(7).
  4. Remove the tail lampbulb (1) from the lamp socket (2).
kiltylake_125.gif


There you are, Happy New year.

KL

Jan 01, 2011 | 2004 Pontiac Vibe

1 Answer

How do you replace rear tail light assembly?


Open the trunk and along the bottom of the tail light, there should be a Philips screw securing a cover piece. (your car may or may not have this piece)
With the cover off, there will be another 2 screws securing the bottom of the tail light assembly. Remove the screws and pull the bottom out and the top is held in by two retainers that should just slide right out

Oct 13, 2009 | 2001 Toyota RAV4

2 Answers

How do you remove rear tail light assembly to replace lamp? I remover the two screws that attach the assembly to the rear pillar but it is still attached to something else.


1. Open the tailgate.
2. Look closely at the side of the brake light cover where it is closest to the tailgate. It is black plastic.
3. You will see two roundish looking outlines in the black plastic (not the two outlines in the plastic that is the same color as your van). There is just enough of a crack to slide a small screwdriver into the crack.
4. Pop the little plastic "doors" up to reveal 10mm nuts with Philips heads.
5. Remove the bolt/screw from each of the two holes. The tail light cover will be loose, but it will not come out yet.
6. Find something small to pry with. It should be plastic or you might scratch your paint.
7. On the side of the van where the tail light cover is flush (the far opposite end of where the bolts were), push a small tool (screwdriver?) under the edge of the cover and pry straight up. There is a peg that fits snugly into a hole in the van. The peg is attached to the tail light cover. With a small flashlight, you should be able to see the peg after prying it up just a little. The peg will pop out and that will allow you to change the bulb.
8. To replace the cover, start by popping the peg back into the hole, then replace the two screws. Finish by snapping the screw covers shut.

Oct 08, 2009 | 2005 Honda Odyssey

1 Answer

2006 Ford Ranger. Rear passenger side tail light


Bad earth connection.Clean or replce wire.

Jun 18, 2009 | 2004 Ford Ranger

2 Answers

Need help for rear tail light assembly on my 2003 trailblazer


Most of the time you can simply remove the tail light assembly from the car pretty easy and just a few screws. If it sdoes not have the screws going through the front of the housing then its rear mount and must be done by lifting the tailgate to get access. Once in the vehicle you should beable to remove the plastic housing covering up the assembly from the inside. Remove the 3-4 screws or bolts and the tail light assembly. Install the new one just the reverse. Pretty easy just take your time.

Joe

May 28, 2009 | 2003 Chevrolet TrailBlazer

2 Answers

Access to tail light wiring harness plug


You have to remove the access panel on the interior side of the passenger compartment to access that connector.. it's a simple procedure after you see the wire harness and bulkhead boot.

May 09, 2009 | 2002 Hyundai Santa Fe

1 Answer

Replacing rear turn signal bulb in 2003 Mustang


remove the trim panel at the very rear of trunk, remove it and place it out of the way, remove tail light Assembly retaining nuts top and bottom, I think there are 6 per side, pull the tail light assembly straight back to access the bulbs for replacement.

Dec 04, 2008 | 2003 Ford Mustang

Not finding what you are looking for?
1991 Toyota 4Runner Logo

Related Topics:

151 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...