Question about 1999 Chevrolet Blazer

2 Answers

How do I remove the console mounted cassette player?

Popped the console cover / tray off, but don't see any fasteners.

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

  • Contributor
  • 2 Answers

I had the same problem. If I wait 10 minutes, it might start the next time. If the security light is blinking, it could be a faulty Bypass in the security system. Apparently this is a fairly common problem. You'll find a permanent bypass solution at http://newrockies.com/.

Posted on Jul 11, 2013

  • Level 1:

    An expert who has achieved level 1.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Contributor
  • 1,199 Answers

It slides down onto posts then clicks into place...to with door in eject pos....it may also just snap down into the bottom slots of inide of door...depends on model!!

Posted on Dec 11, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1997 sunfire shifter cable removal


Hi there:

I will send it anyway and if it helps great.
Disconnect the battery firstRemove the following parts from the transaxle: 2.1. The cable bracket 2.2. The retaining nut 2.3. The cablesRemove the following parts from the control assembly: 3.1. The knob 3.2. The front console 3.3. The shift bootRemove the shift cables from the pin stud on the control assembly.Remove the following parts: 5.1. The spring clip 5.2. The right front sill plate
Pull back the carpet in order to access the shift cables.Remove the following parts from the shift cable assembly: 7.1. The grommet cover bolts 7.2. The cable cover 7.3. The cables

Installation ProcedureRoute the cables.Install the following parts on the cable assembly: 2.1. The cables 2.2. The grommet cable cover 2.3. The attaching bolts at the floor pan Tighten Tighten the bolts to 1.4 Nm (12 lb in). Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.Install the cables to the control assembly using adjustable parallel jaw pliers.Install the spring clips that hold the cables to the control assembly.Install the carpet.Install the sill plate.Install the cables on the transaxle.Install the cable bracket.Install the retaining nut. Tighten Tighten the nut to 10 Nm (89 lb in).Connect the cables.Install the following parts on the control assembly: 11.1. The boot 11.2. The front console 11.3. The knobConnect the negative battery cable.

Also, could try THIS LINK


Hope this helps.

Mar 30, 2012 | 1997 Pontiac Sunfire

1 Answer

Need to remove center console to replace seat belt. After removing 12 screws, console is still firmly in place. What else has to be done?


  1. Remove the two oval covers from the sides of the floor console. Remove the four (two on each side) retaining bolts. Lift or remove the front seat center armrest from the floor console.
  2. Remove one screw from the top rear end of the floor console (directly under the front seat center armrest.
  3. Remove four screws retaining the utility tray beverage holder to floor console. Lift or remove the utility tray beverage holder from the console.
  4. Remove two screws (directly under the utility tray beverage holder) retaining the front end of the floor console to the console panel front mounting bracket.
  5. Lift the floor console from the front and rear console panel mounting brackets.

Feb 27, 2011 | 1996 Ford Explorer

1 Answer

Hjow do i rermove the radio from my 325 i 2003



Removal & Installation-of dashboard which includes removing radio.


CAUTION Many BMW models covered by this manual are equipped with a Supplemental Restraint System (SRS), which uses an air bag. Whenever working near any of the SRS components, such as the impact sensors, the air bag module, steering column and instrument panel, properly disable the SRS.
The instrument panel removal is complex and requires disconnecting many components. Make sure to label and organize the components as they are disconnected, disassembled or removed.
3 Series Models

  1. Disconnect the negative battery cable. If equipped with a Supplemental Restraint System (SRS), wait for a period of 11 minutes before proceeding.
  2. If equipped, disable and remove the SRS components as necessary.
  3. Remove center console as outlined in this section.
  4. Remove the glove box compartment as follows:
    1. Open the glove box door and remove glove compartment mounting screws.
    2. Pull glove box compartment outward, and disconnect the electrical connectors as necessary.

  5. Remove lower left dash trim piece as follows:
    1. Remove the lower dash panel mounting screws.
    2. Pull the lower dash panel to the left and back and disengage it from the driver's side footwell retaining clips.

  6. If equipped, remove the driver's side and passenger airbags.


CAUTION Make sure to store the airbags properly in a safe area.
  1. Remove steering wheel.
  2. Remove driver side knee bolster fasteners and remove.
  3. Remove the following components:

    Instrument cluster Headlight switch Radio Climate control head and module.
  4. Remove the turn signal and windshield wiper/washer stalk switches as outlined in Section 8.
  5. Remove windshield (A-pillar) trim from both left and right sides.
  6. Remove the reinforcement bar below the steering column, then remove steering column shear bolts. Carefully lower steering lightly and support the column to avoid damaging the spindles.


WARNING Lowering the steering column too far can damage the spindles.
  1. Remove the glove compartment support frame fasteners, then remove the frame assembly.
  2. Carefully release and lift out the defroster outlets (both left and right sides) at base of windshield. Remove the screws located below the outlets.
  3. Remove the mounting bolts on the left and right sides of the dash board assembly.
  4. Carefully lift the instrument trim panel off slowly. Make sure all harness connectors and wiring are disconnected.
  5. Installation is the reverse of the removal procedure.

Z3 Models
  1. Disconnect the negative battery cable. Wait for a period of 11 minutes before proceeding.
  2. Disable and remove the (SRS) components as necessary.
  3. Remove center console as outlined in this section.


CAUTION Make sure to store the airbags properly in a safe area.
  1. Remove steering wheel.
  2. Remove driver side knee bolster fasteners and remove.
  3. Remove the following components:

    Instrument cluster Headlight switch Radio Climate control head and module.
  4. Remove the turn signal and windshield wiper/washer stalk switches as outlined in Section 8.
  5. Open the glove box, remove the four finishing caps near the glove box door lock catch and remove the screws.
  6. Remove the trim caps and screws from the far right end of dash and next to the center air vents on right side of the center console.
  7. Close the glove box, then pull it downward and out slightly.
  8. Remove the two screws securing the glove box cover and remove the cover.
  9. Remove the two fasteners securing the passenger side air bag bracket-to-support brace.
  10. Remove the two mounting fasteners on each end of instrument panel, in the door jamb areas.
  11. Remove the two mounting fasteners located under center air vents.
  12. Remove screw trim caps at the base of windshield and remove the screws.
  13. Carefully lift the instrument panel up and remove it from the passenger (right) side of the vehicle.
  14. Installation is the reverse of the removal procedure.

Nov 12, 2010 | 2003 BMW 325

1 Answer

I need to know how to disassembly the instrument panel of f-150 1997


Hi,

Disconnect the Ford's negative battery cable. Turn the truck's front wheels straight ahead and then lock the steering column. Remove the A-pillars' trim by removing the screw covers and then unscrewing the mounting fasteners.

Remove the center console if equipped by unfastening the nearby trim panels, prying off the shifter trim panel, disconnecting the shifter cable and unfastening the console. Remove the steering wheel, then unfasten and remove the steering column covers, starting with the lower cover.

Remove the instrument cluster. Unscrew and pry off the knee bolster with the aid of a flat-blade tool, then unscrew and remove the instrument cluster bezel in a similar way. Disconnect the electrical connectors, remove the cluster's mounting bolts and remove the cluster--you'll need to disconnect the gear position indicator on an automatic transmission.

Remove the glove box by opening the door, pressing on the sides of the compartment bin together, pulling the door down and removing the fasteners at the bottom. Remove the center brace cover, center bezel and upper finish panel by removing their fasteners or prying them off their clips.

Detach the end caps to the panel with a trim stick or flat-bladed tool, then detach the hood release by removing its screw. Pry off the scuff plates and kick panels from the door frame. Pry up the defrost grilles with the same flat tool.

Disconnect the steering column shaft. Disconnect the electrical connectors from the column's harness, detach the shift cable and transmission indicator cable if you have automatic transmission, remove the pinch bolt from the intermediate shaft coupler and separate the intermediate shaft from the steering shaft.

Disconnect all remaining electrical connectors to the panel and unbolt all fasteners for the panel around the top, left and right sides and the ends along with the brackets at the center. Lift and pull the panel away from the windshield with an assistant's help, disconnect all remaining connectors and carry the panel out the driver's door.

Good luck.

Nov 07, 2010 | 1997 Ford F150 Regular Cab

1 Answer

How do i install a new dash for 83 mazda rx7


Instrument Panel and Pad REMOVAL & INSTALLATION
  1. Disconnect the negative battery cable.
  2. If so equipped, unfasten the inside hood release handle.
  3. Remove the steering wheel and the lower steering column cover.
  4. Remove the glove box, switch panel and console. Fig. 1: Loosen the retaining nut to unfasten the inside hood release handle 85810013.jpg
    Fig. 2: If necessary, remove the dash mounted speaker covers to access hidden instrument panel bolts 85810003.jpg
    Fig. 3: Due to space limitations, some bolts are best removed with an open end or box wrench 85810004.jpg
    Fig. 4: Other bolts are easily removed with a socket 85810005.jpg

  5. Remove the meter (gauge) hood, heater control panel mounting screws and separate the heater controls from the instrument panel frame. Remove the combination meter.
  6. Remove the air duct(s) and the steering shaft mounting bracket bolts. Allow the column to lower.
  7. Disconnect and label the meter wiring. Unfasten the mounting bolts and remove the crash pad and instrument panel. Fig. 5: Some of the instrument panel attaching bolts are hidden behind removable trim covers or plugs. Carefully pry off the cover . . . 85810006.jpg
    Fig. 6: . . . then remove the bolts with a socket 85810007.jpg
    Fig. 7: The glove box must be removed to unfasten some of the instrument panel retaining bolts 85810008.jpg
    Fig. 8: Other retaining bolts are accessible with the meter hood and combination meter removed 85810009.jpg
    To install:
  8. Position and fasten the crash pad and instrument panel, being careful to route the wiring correctly. Attach the meter wiring to its appropriate connections.
  9. Raise the steering column to its normal operating position and install the steering shaft mounting bracket bolts. Connect the air ducts.
  10. Install the combination meter. Install the heater controls into the instrument panel frame with the mounting screws. Attach the meter hood.
  11. Install the console, switch panel and glove box.
  12. Install the steering wheel column cover and steering wheel.
  13. If applicable, attach the inside hood release handle.
  14. Connect the negative battery cable.
prev.gif next.gif

Nov 05, 2010 | 1983 Mazda RX-7

1 Answer

Center console disasembly instructions . we are trying to remove the center console


Base Console, Floor, Ranger, Explorer Removal and Installation
  1. Remove the two oval covers from the sides of the floor console. Remove the four (two on each side) retaining bolts. Lift or remove the front seat center armrest (644A22) from the floor console.
  1. Remove one screw from the top rear end of the floor console (directly under the front seat center armrest.
  1. Remove four screws retaining the utility tray beverage holder to floor console. Lift or remove the utility tray beverage holder from the console.
  1. Remove two screws (directly under the utility tray beverage holder) retaining the front end of the floor console to the console panel front mounting bracket.
  1. Lift the floor console from the front and rear console panel mounting brackets.

c758709.gif

Apr 01, 2010 | 1996 Ford Explorer

1 Answer

Replace heater core in 1994 pontiac grand am


Removal & Installation


  1. Disconnect the negative battery cable.
  2. Drain and recycle the engine coolant.
  3. Raise and safely support the front of the vehicle.
  4. If necessary, remove the rear lateral transaxle strut mount.
  5. Detach the drain tube, then disconnect the heater hoses from the core tubes.
  6. Carefully lower the vehicle.
  7. Remove the console if equipped.
  8. Unfasten and remove the sound insulators, console extensions and/or steering column filler, as required.
2a4e97b.gif
Unfasten the sound insulator retaining bolts ...

7ed3765.gif
... then remove the sound insulator

  1. On some models it may be necessary to remove the steering column opening filler.
  2. Remove the floor or console outlet ductwork and hoses.
  3. Remove the heater core access cover.
a5f8d39.gif

Remove the heater core access cover

Unfasten the heater core mounting clamps/bolts, then extract the heater core from the vehicle.

a5c4734.gif
Unfasten the heater core retaining bolts; most later models are secured with clamps.

b2756d9.gif
Remove the heater core from the vehicle

To install:
  1. Install the heater core, then secure using the clamps/bolts.
  2. Fasten the heater core cover.
  3. Connect the outlet hoses and ducts.
  4. Install the sound insulators, console extensions and/or steering column filler.
  5. Raise and safely support the vehicle.
  6. Install the drain tube and connect the heater hoses to the core tubes.
  7. If removed, install the rear lateral transaxle strut mount, if removed.
  8. Carefully lower the vehicle.
  9. Connect the negative battery cable.
  10. Fill cooling system and check for leaks. Start the engine and allow to come to normal operating temperature. Recheck for leaks and check coolant level. Add if necessary.

Nov 13, 2009 | 1994 Pontiac Grand Am

1 Answer

BMW 328i Starter how to replaice


1999 BMW 328I 2.8L EFI DOHC 6cyl

Starter - Removal & Installation

The starter motor on some models is very difficult to see from the top of engine compartment as it is covered by the intake manifold. On these models, without removing the intake manifold, the starter motor must be removed from underneath the vehicle. Because the starter motor mounting bolts are not easy to access, a long extension with a universal joint mounted on a proper sized socket could be used. A three foot transmission extension is commercially available from tool vendors that has a 3 / 8 inch drive of the driven end and 1 / 2 inch drive on the drive end. If used with a non-binding impact universal joint and a proper fitting impact socket, the starter motor fasteners can be removed from underneath the vehicle.
Once the starter motor fasteners are removed, the starter motor may have to be moved side-to-side several times to loosen the dowel pin if it has corroded in place.

NOTE When the battery is disconnected, the radio code, on-board computer and clock settings will be lost. The radio code should be obtained before disconnecting the battery or radio. Once the battery has been reconnected, the radio will not function unless the code is keyed in.
Starter motor electrical terminal fastener torque specifications for all models:
M5 terminal fasteners: 44 inch lbs. (5 Nm)
M6 terminal fasteners: 53 inch lbs. (6 Nm)
M8 terminal fasteners: 115 inch lbs. (13 Nm)
Starter motor mounting fasteners:
Hex head bolts: 36 ft. lbs. (49 Nm)
Torx bolts: 32 ft. lbs. (43 Nm) Starter motor electrical terminal fastener torque specifications for all models:
M5 terminal fasteners: 44 inch lbs. (5 Nm)
M6 terminal fasteners: 53 inch lbs. (6 Nm)
M8 terminal fasteners: 115 inch lbs. (13 Nm) Starter motor mounting fasteners:
Hex head bolts: 36 ft. lbs. (49 Nm)
Torx bolts: 32 ft. lbs. (43 Nm) E36 6-Cylinder Engines
Automatic Transmission Models
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Set the ignition switch to the OFF position.
  3. Disconnect the negative battery cable.
  4. Remove the climate control air intake duct at the rear of the engine compartment as follows:
    1. Release the grille clips at the rear and lift the grille upward from the rubber seal, then remove the seal.
    2. Remove the two self tapping Phillips screws from inside the duct to release the electrical harness housing.
    3. Press the electrical housing downward to expose and remove the two hex head self tapping screws on each side of the duct and lift the duct up and out of the engine compartment.
  5. Remove the intake manifold trim and valve cover trim covers.
  6. Disconnect the ignition coil electrical connectors and ground straps, label for reinstallation and place aside.
  7. Remove the two fasteners that secure the fuel injection electrical connector harness to the rail. Remove the harness and carefully place aside toward the back of the engine compartment behind the right side strut tower.
  8. Remove the intake manifold.
  9. Remove the electrical leads from the starter motor and place aside.
  10. Remove the starter motor mounting fasteners at the transmission bell housing, then remove the two mounting nuts at the L-shaped mounting bracket.
  11. Loosen the L-shaped bracket to engine block mounting bolt slightly, then remove the bolt while supporting the starter motor.
  12. Remove the bracket, then lift the starter motor upward away from the engine.
  13. Visually inspect the starter pinion and ring gears for any signs of damage.
  14. Installation is in reverse order of removal.
Manual Transmission Models
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Set the ignition switch to the OFF position.
  3. Disconnect the negative battery cable.
  4. Raise and safely support the vehicle.
  5. Remove the fasteners for the reinforcement mounted between the frame rails just behind the rear lower control arm bushing brackets. Mark the bar-s direction for proper reinstallation and remove the bar.
  6. Remove the fuel line cover located near the left side rear lower control arm bushing bracket.
  7. Release the fuel lines and reverse light wiring from their routing brackets.
  8. Note the routing of the starter motor electrical wires, remove the wire mounting nuts, and place the wires aside.
  9. Remove the top and bottom starter motor to engine-transmission mounting fasteners.
  10. Remove the two mounting nuts at the L-shaped mounting bracket.
  11. Loosen the L-shaped bracket to engine block mounting bolt slightly, then remove the bolt while supporting the starter motor.
  12. Remove the bracket and carefully lower the starter motor downward away from the engine.
  13. Visually inspect the starter pinion and ring gears for any signs of damage.
  14. Installation is in reverse order of removal.

Fig. A view of the starter motor mounting fasteners and dowel pin. The mounting bolts are threaded into the starter motor

cd45991.jpg

Fig. The starter motor mounting bolts are a different size than the transmission-to-engine mounting bolts

2cbfa11.jpg

I hope help you with this (rated this help) Good luck.

Sep 22, 2009 | 1999 BMW 328 Series

2 Answers

How to remove heater core from 2000 Pontiac Montana. Antifreeze leaking on floor.


Wow I hope youre mechanicly inclined, big job the entire dash & carrier have to come out 7-15 hr job if you know what you are doing to much to list hear I would check heater hoses at fire wall first make sure they arnt leaking. I wish you well

Aug 31, 2009 | Pontiac Montana Cars & Trucks

1 Answer

Replacing a heater core in a 1994 olds. achieva.


  1. Disconnect the negative battery cable.
  2. Drain and recycle the engine coolant.
  3. Raise and safely support the front of the vehicle.
  4. If necessary, remove the rear lateral transaxle strut mount.
  5. Detach the drain tube, then disconnect the heater hoses from the core tubes.
  6. Carefully lower the vehicle.
  7. Remove the console if equipped.
  8. Unfasten and remove the sound insulators, console extensions and/or steering column filler, as required.
0900c152800a93fc.jpgFig. 1: Unfasten the sound insulator retaining bolts ... 0900c152800a93fd.jpgFig. 2: ... then remove the sound insulator
  1. On some models it may be necessary to remove the steering column opening filler.
  2. Remove the floor or console outlet ductwork and hoses.
  3. Remove the heater core access cover.
0900c152800a93fe.jpgFig. 3: Remove the heater core access cover
  1. Unfasten the heater core mounting clamps/bolts, then extract the heater core from the vehicle.
0900c152800a93ff.jpgFig. 4: Unfasten the heater core retaining bolts; most later models are secured with clamps 0900c152800a9400.jpgFig. 5: Remove the heater core from the vehicleTo install:
  1. Install the heater core, then secure using the clamps/bolts.
  2. Fasten the heater core cover.
  3. Connect the outlet hoses and ducts.
  4. Install the sound insulators, console extensions and/or steering column filler.
  5. Raise and safely support the vehicle.
  6. Install the drain tube and connect the heater hoses to the core tubes.
  7. If removed, install the rear lateral transaxle strut mount, if removed.
  8. Carefully lower the vehicle.
  9. Connect the negative battery cable.
  10. Fill cooling system and check for leaks. Start the engine and allow to come to normal operating temperature. Recheck for leaks and check coolant level. Add if necessary.6d0c523.jpg182943c.jpg164cdd5.jpg8032c04.jpg18be863.jpg

Oct 21, 2008 | 1994 Oldsmobile Achieva Special Edition

Not finding what you are looking for?
1999 Chevrolet Blazer Logo

Related Topics:

153 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...