Question about 2005 Chrysler Pacifica

2 Answers

How to set up for 2005 pacifica garage door opener

Universal garage door opener

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

How about a real answer......

1. Press and hold the two outer HomeLink buttons, and
release only when the indicator light begins to flash (after
20 seconds). Do not hold the buttons for longer than 30
seconds and do not repeat step one to program a second
and/or third hand-held transmitter to the remaining two
HomeLink buttons.

2. Position the end of your hand-held transmitter 1-3
inches (3-8 cm) away from the HomeLink buttons while
keeping the indicator light in view.
3. Simultaneously press and hold both the HomeLink
button that you want to train and the hand-held transmitter
buttons. Do not release the buttons until step 4
has been completed.

4. The HomeLink indicator light will flash slowly and
then rapidly after HomeLink successfully receives the
frequency signal from the hand-held transmitter. Release
both buttons after the indicator light changes from the
slow to the rapid flash.
5. Press and hold the just trained HomeLink button and
observe the indicator light. If the indicator light stays on
constantly, programming is complete
and your device
should activate when the HomeLink button is pressed
and released.

Posted on Dec 27, 2009

  • wwwbertich10 Nov 09, 2010

    You also need to mention that the garage HomeLink system doesn't always work so you have to go unscrew the system and find where the wire not the red one but the black receiver wire and find the learn or smart button and push it hard and firmly then get back to your car within 30 seconds and push the button you would like to set the garage door as and then your done.

×

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 18 Answers

Look in the manuel

Posted on Dec 29, 2008

3 Suggested Answers

  • 4 Answers

SOURCE: program instruction garage door opener in 2005 chrysler pacifica

You can download the operators manual for free at chrysler.com. It has the instructions to program the garage door opener. It's fairly easy with the instructions.

Good Luck,
Ray

Posted on May 11, 2009

  • 1 Answer

SOURCE: universal garage opener

The solution is in the owners manual.If you want to program the "homelink transmitter" in your car,you will need a remote unit for your garage door opener to do this.It is fairly easy and straightforward.I programmed my 07 Pac and it works great.Good luck!

Posted on Mar 22, 2009

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I am getting ready to sell. How do I clear the settings on the garage door opener buttons?


Hold the first and third buttons for about 30 seconds. It probably won't take that long, but it will make sure that they are cleared. The red LED light will blink rapidly. That is the signal that it is cleared. Just to make sure, try to open or close the garage door that it was programmed to. Congratulations on the new vehical adventure! Hope this helps! Please feel free to ask and questions if needed.

Apr 25, 2011 | 2005 Chrysler Pacifica

1 Answer

How to program 2007 chrysler Pacifica to open garage door opener


GOTO Homelink.com


They make the system - you can download step by step instructions.


Follow carefully if you miss anything you need to start over.


Hope this helps.

Feb 20, 2011 | 2005 Chrysler Pacifica

1 Answer

How do I program the remote garage door opener in my 2005 Pacifica ?


Sorry, the process is simple but too lengthy to post here.

Goto homelink.com

They make the system and have very complete instructions you can download.

PLEASE NOTE: MOST but not ALL Brands / models of opener will work with this system.

Apr 06, 2010 | 2005 Chrysler Pacifica

1 Answer

My 2005 pacifica the door is making a carnking sound only when you open the door


some WD40 or similar lubricant sprayed directly on the door hinges (try to spray the inners of the hinge with the WD40 straw nozzle) - should fixya right up !

Jul 22, 2009 | 2005 Chrysler Pacifica

2 Answers

Program instruction garage door opener in 2005 chrysler pacifica


if your garage motor have rolling codes you need to put your car inside garage near the motor leave ignition on go to the motor locate learn button press it then quickly go to the car and press and hold one of the buttons for approximately 30 sec or until it start blinking rapidly, if you have a regular motor take one hand held opener go inside car ignition on same time press open button on handheld remote and on the car button 30 sec and it should be programmed.

Apr 24, 2009 | 2005 Chrysler Pacifica

1 Answer

Program 2004 mercury mountainer garage opener


Verify the hand-held transmitter is operative.
Prepare for programming the universal transmitter by erasing all three channels (hold down the two outside buttons until the red light begins to flash [20-30 seconds]). Release both buttons.
Select one of the three universal transmitter channels to be programmed by pressing the desired button
Hold the end of the hand-held transmitter 25-51 mm (1-2 in) from the front surface of the universal transmitter so that the red light can still be seen
Use both hands to press the hand-held transmitter button and the desired button on the universal transmitter. Do not release either button.
Hold down both buttons until the red light on the universal transmitter flashes, first slowly and then rapidly. Release both buttons when the rapid flashing begins. The universal transmitter has successfully learned the new frequency signal and can be used in place of the hand-held transmitter(s).
If the hand-held transmitter appears to program the universal transmitter but does not open the garage door, the garage door opener may have a code protected or rolling code feature.
To operate, simply press the appropriate button on the universal transmitter. The red light is on while the signal is being transmitted.
IF THE GARAGE OPENER HAS ROLLING CODES---
program as above then------
Train the garage door opener receiver to recognize the universal transmitter.
Remove the cover panel from the garage door opener receiver.
Locate the training button on the garage door opener receiver. Location and color of the button may vary by garage door opener manufacturer. Refer to the garage door opener instruction manual or owner literature.
Press the training button on the garage door opener receiver for 1-2 seconds.
Press the programmed universal transmitter button for as long as the universal transmitter red light flashes (1-2 seconds). Release the button and re-press the button to confirm that the universal transmitter is trained to the receiver.
The garage door opener should recognize the universal transmitter.

Apr 01, 2009 | 2004 Mercury Mountaineer

1 Answer

Setting garage door opener


Most openers are programmed the same. You normally program the house garage opener to accept the new remote. Your garage opener will have a button to press to add in a new remote. Normally you press this and then press the remote in the car and hold until your lights on your opener flash or the garage door closes. (check your manual on your garage door opener)

Mar 27, 2009 | 2005 Chevrolet TrailBlazer

2 Answers

Universal garage opener


The solution is in the owners manual.If you want to program the "homelink transmitter" in your car,you will need a remote unit for your garage door opener to do this.It is fairly easy and straightforward.I programmed my 07 Pac and it works great.Good luck!

Mar 08, 2009 | 2005 Chrysler Pacifica

1 Answer

Alarm just goes off


YOU MAY HAVE A DOOR SWITCH GROUNDING ITSELF. CHECK DOORS AND HATCH SWITCHES

Dec 30, 2008 | 2005 Chrysler Pacifica

Not finding what you are looking for?
2005 Chrysler Pacifica Logo

928 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

70374 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6878 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...