Question about 2000 Audi A6

3 Answers

Audi A6 2000 2.4 timing belt &valve covers

''Audi A6 2000 is the 2000 A6 2 4 motor use the same timing belt valve cover gaskets and cam seals t''

Posted by on

  • blancomono Dec 10, 2008

    Is the 2000 Audi 2.4 the same sa the 2.8

  • blancomono Dec 10, 2008

    thank you i need to chang them and the US parts do not have the 2.4 in there parts book so if I can use the 2.8 parts this helps

×

3 Answers

  • Level 1:

    An expert who has achieved level 1.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Contributor
  • 1,199 Answers

Yes they are compatable!

Posted on Dec 10, 2008

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 399 Answers

Yes its the same and u can carry on in replacing them.but check out the proper marks from where u install the belt.

Posted on Dec 10, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Audi Master
  • 60,867 Answers

Yes it does.

Posted on Dec 10, 2008

  • yadayada
    yadayada Dec 10, 2008

    I don't get it, give the same answer but get no credit, hum?

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Oil leak at bottom of timming belt cover


what engine.? lots of engines, used. and 21 models of civic, USA.
its usually.
1: valve cover, (yes, most can leak from top down behind the belt.
2: cam seals
3: crank end seal
4: oil pump seals.
6: oil pan ( last choice)

finding oil leaks takes hard work , clean, it find it .
or use the dye kits.

gravity and wind, allows it to go where ever IT wants.
so it must be clean first to find it.. see?
or use the dye kits, it shows a live leak best.

ever look here?
http://estore.honda.com/honda/parts/view-honda-parts-catalog-detail.asp?m=1997-civic-2-dx-4at&sn=&b=E++09&dl=

question, at the 60k mile service points. you check lash, settings.
with a new timing belt. and at such point, a new valve cover gasket gets fitted, did you? if yes, its not leaking if not>????
the front edge of the VC gasket, leaks down behind what i call
the VC leak hidder, tin pan. plate. behind the cam cog
is a plate, and the VC leaks down from there to the cam seal
then down front of engine, then past crank seal the, to cover.
seen this on all most all OHC engines...
cause, nobody does the 60k or does it and uses the old gaskets.
id look there first. but id dont have service history.
start high work down due to gravity.....
the FSM is here.
see that too. "free" too
http://hondatech.info/downloads/Auto/Manuals/Civic/

Dec 17, 2013 | 1997 Honda Civic

1 Answer

Oil leak front engine timing chan


1995 Tracker would have a timing BELT. Normal oil leak points (in order) on a Suzuki G16 engine are the distributor base (rear of motor), valve cover (top of motor), front main seal (behind lower timing belt cog) cam seal (behind the upper timing belt cog) and rear main seal. (behind the flywheel). I'd suspect the front main seal or cam seal. I use foot power to help find oil leaks.

Dec 24, 2012 | 1995 Geo Tracker

1 Answer

Oil leak from rocca cover or cam seal


I don't understand what a rocca cover is, but your two most common oil leak locations are the front cam seal behind the timing belt pulley and the rear cam journal plug in the valve cover.
For a leak at the front, next time you replace your timing belt, unbolt the pulley, extract the old seal with a sharp hook, and press in a new seal. Be sure that the new seal is pressed in straight, and grease the lips before you press it in. Often, the front crankshaft seal fails about the same time, so replace that one as well while you have the timing belt off.
For a leak at the rear, reach back there behind the valve cover with solvent on a rag and clean it up nice and dry, then coat the edges of the rubber plug liberally with silicone seal. Allow to dry. Replace the rubber plug next time you have the valve cover off, but use some silicone seal to secure the new one so it stays in place and won't start leaking.
These cars are prone to valve cover gasket leaks, so expect to replace the valve cover gasket every few years. This is a particular problem if you use synthetic oil.
Any time you have problems with oil leaks, suspect that the crankcase is pressurizing due to a plugged ventilation system. Check the flame arrestor to make sure it is clean and clear. The flame arrestor is between the legs of the intake manifold, generally in a hard-to-get-at location. Also, blow down the hose below the flame arrestor to make sure that the oil mist separator box on the side of the engine block has not plugged up with sludge.

May 10, 2011 | 1988 Volvo 240

1 Answer

What would be a reasonable price for the following work and how would I know if these things were actually done? 2003 Audi A6 Transmission filter kit Water pump Timing belt Idler pulley Rear...


it is VERY unlikely that a seven year old car would need that much done to it, unless it had 200,000 or more miles on it. New oil should be the color of honey, not dark brown. That's the easy check.

Dec 30, 2010 | 2003 Audi A6

2 Answers

2002 Passat, 30 valve V6 has oil leaking on exhaust manifold. VW dealer says its the cam adjuster seals. It looks to me like its just the valve cover gaskets but I can't get an engine schematic to see the...


I have a 2000 Passat V6. They told me that same thing. To replace the gaskets is easy. You just remove the covers and the air filter box and unscrew the 6 bolts holding the valve cover on it and there you go. You want to clean around the gasket service and add a little bit of sealant to the edges. Replace the old gaskets and put everything back together, be careful not to overtighten the bolts, can flatten out the gasket and cause oil leak again. On the right side of the engine, you have to remove the coolant box to get to it. Same procedure....

Oct 18, 2010 | 2002 Volkswagen Passat

3 Answers

1995 toyota camry leaking oil from behind the timing belt cover. Isn't this a major repair? Is the leak more than likely a camshaft seal?


If you haven't had the timing belt replace (60,000 miles is the suggested service intervale) this is an overlap of having the timing belt replaced.
If the timing belt is not due for replacement and its the cam shaft seal that is leaking. Its a pretty easy fix. Remove the top timing belt cover , and the crankshaft sensor wiring you may have to remove the front engine mount . Set #1 piston at TDC, Loosen tensioner w/ spring slip off belt. **Remove sprocket pull out old seal with a sharp pick. Greese and install new seal make sure its flush with its bore . Reistall sprocket. Slide belt over Cam sprocket tighten tensioner. Install cover and mount (if applicable) Check timing marks by turning crank two revolutions.
** If CamSprocket Bolt is difficult to remove then remove valve cover and use a 21mm wrench to hold the Camshaft while you crack off Cam Sprocket Bolt.
You will see the groves on the Camshaft where you can place a wrench to hold the shaft.
After you replaced the seal replace the valve cover gasket ONLY IF YOU HAD TO REMOVE THE COVER TO HOLD THE CAM WHILE REMOVING ITS BOLT.

This is about as major as it gets.

May 12, 2010 | 1995 Toyota Camry

2 Answers

1989 honda accord oil leeak cam/crankshaft


Take valve cover gasket bolt out replace... An when you do the lower crank seal you have to take off oil pan.. Big job but it can be done..

Jun 27, 2009 | 1989 Honda Civic

2 Answers

Oil leak in my 98 mazda protege


Could be a rear main seal.

Apr 02, 2009 | 1998 Mazda Protege

2 Answers

Preparing a salvage motor for transplant


4. Belt tensioner
5. oil pan gasket
6. valve cover gasket
7. All other seals in timing area and cover.

Dec 10, 2008 | 1996 Saturn SL

1 Answer

I have an 86 honda accord lxi with an oil leak. we have changed the valve cover gasket, oil pan gasket, oil pump gaskets, and the cam seal, but it still leaks from the timing belt cover and sprays onto the...


There are two slots in the valve cover right by the cam shaft sprocket that have to be honda bonded or black rtv. look closely at the valve cover right above the gasket underneath the timing belt cover. Hope that helps.

Jul 27, 2008 | 1986 Honda Prelude

Not finding what you are looking for?
2000 Audi A6 Logo

Related Topics:

137 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

yadayada
yadayada

Level 3 Expert

60867 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

13152 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...