Question about 2005 Chevrolet Colorado

1 Answer

05 chevy colorado

Broke rear (drivers-side) tail light red plastic cover. have ordered to piece and would like instructios to remove & replace new one. thank you

Posted by on

  • s_perruccio Dec 11, 2008

    thank you, exactly what i needed to know.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 303 Answers

Open the tail gate and look for the two screws on the inside of the bed there might be two on the out side if there is not they are held it by clips on the out side remove inside screws and pull straight out

Posted on Dec 10, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do we replace the tailgate handle on a 2005 chevy colorado?


REMOVE TAIL GATE HANDLE YOU USE A TRIM TOOL OR FLAT SCREW DRIVER PRY OFF THE HANDLE ESCUTCHEON DOWN AND AWAY FROM THE TAILGATE IF SCREW DRIVER IS USED COVER THE TIP WITH ELECRICAL TAPE TO PREVENT DAMAGING PAINT SURFACE.FROM THE BED SIDE OF THE TAILGATE REMOVE THE HANDLE MOUNTING BOLTS.ROTATE THE PLASTIC RETAINING CLIPS OFF THE CONTROL RODS AND DETACH THE RODS FROM THE HANDLE. REMOVE THE BOLTS AND WITHDRAW THE LATCH FROM THE END OF THE TAILGATE.PUT EVERY THING BACK VISA VERSA.

Aug 04, 2011 | 2005 Chevrolet Avalanche

1 Answer

Drivers side rear blinker light needs replaced


Open the tail gate, and you will see on the side of the tail light housing two screws that you will need to unscrew in order to take the housing out. If it is the tail light ,that is on the actual gate, open the tail gate and remove the plastic bed liner there are few of screws that need to be removed. Hope this helps you fix it.

Apr 17, 2010 | 2003 Subaru Baja

1 Answer

How do you replace rear tail light assembly?


Open the trunk and along the bottom of the tail light, there should be a Philips screw securing a cover piece. (your car may or may not have this piece)
With the cover off, there will be another 2 screws securing the bottom of the tail light assembly. Remove the screws and pull the bottom out and the top is held in by two retainers that should just slide right out

Oct 13, 2009 | 2001 Toyota RAV4

2 Answers

Need help for rear tail light assembly on my 2003 trailblazer


Most of the time you can simply remove the tail light assembly from the car pretty easy and just a few screws. If it sdoes not have the screws going through the front of the housing then its rear mount and must be done by lifting the tailgate to get access. Once in the vehicle you should beable to remove the plastic housing covering up the assembly from the inside. Remove the 3-4 screws or bolts and the tail light assembly. Install the new one just the reverse. Pretty easy just take your time.

Joe

May 28, 2009 | 2003 Chevrolet TrailBlazer

1 Answer

2005 Chevy Colorado edit


If you put the tail gate down, there is 2 screw (phillips) that holds the tail light in place. Remove them & you can twist the bulb out. Thats it, put back together in reverse. Hope this helps.

May 21, 2009 | 2005 Chevrolet Colorado

2 Answers

Access to tail light wiring harness plug


You have to remove the access panel on the interior side of the passenger compartment to access that connector.. it's a simple procedure after you see the wire harness and bulkhead boot.

May 09, 2009 | 2002 Hyundai Santa Fe

1 Answer

Intake manifold cover


remove oil cap steam an it should just lift off

Feb 23, 2009 | 2005 Chevrolet Colorado

2 Answers

Vacuum leak


mine is doing the same, it's your pcv receptor on the manifold. that hard plastic cover is actually part of the intake itself, if it "came off" it would cut your intake in half. that seem seals the two halfs together. you gotta pull the whole intake off and replace it... or jimmy rig it.

Feb 23, 2009 | 2005 Chevrolet Colorado

1 Answer

SOLUTION: HOW TO REPLACE REAR BULBS ON 2002 & 2004 BUICK LESABRE


Rear tail lamps for the 2002 La Sabre has eight nuts that hold the cover in place ( one piece-all acroos the back of the car). Do not remove the nuts for the lock, the cover sits in place and is not secured to the lock. Use a 10 mm deep well socket. remove the nuts and lift the cover to replace the burned out bulb(s). The bulbs are #194 or #198 (very small bulbs), not the 3057. It is easy to locate the burned out bulbs by putting the car in reverse and shutting off the engine and then put the ignition key in the accessory mode. The lights will light unless they are burned out. Simply pull them out and replace with the new ones and put the cover back in place and secure the nuts.

Feb 13, 2009 | 2004 Buick LeSabre

2 Answers

Colorado Electrical Troubles


sistema seguidad se activa , porque

Jun 16, 2008 | 2005 Chevrolet Colorado

Not finding what you are looking for?
2005 Chevrolet Colorado Logo

121 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...