Question about 1995 Jeep Cherokee

1 Answer

How to remove the ignition switch in a 1993 Jeep Cherokee?

How do i remove the ignition switch in a 1993 Jeep Cherokee ? need to remove ignition as it has been damaged

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 33 Answers

You need to remove steering wheel and you will see how its done once you get inside

Posted on Dec 10, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to remove and replace ignition switch in a 1988 Jeep loredo

RTM yet,
what is loredo.
what jeep model, cherokee?
my guess its a Cherokee Laredo. 1988
with a 4.0L inline six engine, and the horrid French Renix EFI injection system. (had 2 , i did, hug mileage packed up.)
this jeep books are hard to find, sold mine, from 1988 .
the ignition switch is not hard.
the early XJ jeep by AMC (of Rambler fame)

1993 xj book is free, and not rare like 88s
i call it behind the 8 ball.
read chapter 19- page 50
on XJ 93

i think the 88s the switch is x10 more easy
and more easy to steal.(thus the change)
ive posted answers here on this car, before with same year
and same exact question.

ever use google on the rare, its about all there is...
its in plain site if you look, not buried like 93s

off masters site

Feb 29, 2016 | Jeep Cars & Trucks

1 Answer

Why don't i have power to my ignition or fuel pump on my 1993 Jeep Grand Cherokee?

The problem could be a bad ignition switch. I would start by checking ALL the fuses - both under the dash and under the hood. The under hood fuse panel should also have a fuel pump relay. You may want to replace that to see if it helps.

Jun 17, 2014 | 1993 Jeep Grand Cherokee

2 Answers

Where is the ignition switch on 1993 jeep cherokee country

I use and I'd recommend you register for free at Once registered you'll have access to repair and shop manuals for virtually any car or truck. All the data and diagrams you need now or may need in the future will be a couple of mouse clicks away.

Jun 11, 2011 | 1993 Jeep Cherokee Country

1 Answer

Have a 93 jeep cherokee. Ignition is locked in the on position, will not crank over, but there is power.

If the key will not turn past the on position, and it turns to all other positions then you need to replace your ignition switch, if it doesn't turn anywhere but the on position then you need to replace your tumbler. For the ignition switch you will need a mechanic, for the tumbler you will need a locksmith.

Nov 05, 2010 | 1993 Jeep Grand Cherokee

1 Answer

1993 Jeep GC Limited - Overhead display is too dim to be useful - especially when headlights are on. Can this be adjusted, and how?

It's the dimmer switch....follow below:

Without Air Bag The ignition switch is located on the lower part of the steering column.
  1. Place the ignition in the LOCK position

Ignition/dimmer switch assembly

  1. Remove any components necessary to access the switch.
  2. Remove the two switch mounting screws.
  3. Disconnect the switch from the rod.
  4. Disconnect the wiring and remove the switch.
To install:

Ignition switch rod positioning

  1. On non-tilt columns:
    1. Move the ignition switch slider to the OFF unlocked position (move the slider all the way down, then back two clicks). The remote rod hole in the ignition switch slider should now be centered.
    2. Insert the remote rod in the ignition switch slider hole and install the ignition switch on the steering column. Tighten the attaching screws to 35 inch lbs. (4 Nm).
  2. On tilt columns:
    1. Insert the ignition key in the lock cylinder and turn the cylinder to the OFF unlocked position.
    2. Move the ignition switch downward to eliminate any slack and tighten the attaching screws to 35 inch lbs. (4 Nm).
  3. Install any components removed for switch access.

Aug 13, 2010 | 1993 Jeep Grand Cherokee

1 Answer

1993 jeep Cherokee sport ignition sometimes works

check the connections between the starter, battery and ignition. if all are fine replace the ignition switch

Apr 29, 2010 | 1993 Jeep Cherokee Country

1 Answer

How do you remove the ignition switch from a 1993 jeep Cherokee? Apparently the key switch activates a lever or or rod inside the steering column that operates this switch but how do you get it apart? we...

Disconnect negative battery cable, remove upper and lower covers (three screws); remove the ignition switch mounting screws.

Pull switch away from the column and remove the connectos from the ignition switch.

Also I suggest check the 93ZJ-Secc-8D-Ignition-Systems for more details and graphics.

I hope helps with this (remember rated this help) Good luck.

Dec 21, 2009 | 1993 Jeep Grand Cherokee

1 Answer

1993 jeep cherokee

Your ignition switch is probably bad. Pull one from the junkyard to save money and you will be up in no time.

Sep 24, 2008 | 1993 Jeep Cherokee Country

Not finding what you are looking for?
1995 Jeep Cherokee Logo

Related Topics:

659 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts


Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides