Question about 1996 Saturn SL

2 Answers

Preparing a salvage motor for transplant

What needs to be replaced on motor with 69000 miles on it before transplant???
1. water pump
2 timing belt
3 rear seal
4. ???
5.
6.
What is you opinion???

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 341 Answers

I would do what you have plus ..front seal..oil pan gasket ...valve cover gasket.your thinking right.. whole lot easier to do before than after its installed .......

Posted on Dec 10, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 740 Answers

4. Belt tensioner
5. oil pan gasket
6. valve cover gasket
7. All other seals in timing area and cover.

Posted on Dec 10, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When do I change the timing belt of a 2004 nissan quest


Nissan recommends replacement of the timing belt and water pump at 84 months or 105K miles whichever comes first. ALWAYS replace the water pump at the same time as the timing belt or you will be out the same amount of labor in 2-3 months when the pump goes bad after the timing belt replacement.

Dec 03, 2013 | 1993 Nissan Quest

1 Answer

How do i change a waterpump on a 2001Volkswagen cabrio?


Your Cabrio has one of several 2.0L Volkswagen engines - determine your engine type from the
8th digit of your VIN, which will be either an "A", or "C",both are 2.0L engines.

Volkswagen 2.0L engines offered in 2001:
(a) 2.0L (Aba) Engine
(b) 2.0L (Aeg/Avh/Azg/Bdc/Bev/Bgd) Engine
(c) 2.0L (Aeg/Avh/Azg/Bdf) Engine

For completeness, I've included the water pump maintenance manual entries for all (3) 2.0L VW
engines offered in 2001. Note that the instructions below include (3) illustrations, which are
reproduced faithfully from the manual, but the last (2) illustrations are identical, since the last two
engines in the list above are virtually identical.

Volkswagen 2001 engines - water pump replacement

2.0L (Aba) Engine

Before servicing the vehicle, refer to the Precautions section.

Remove or disconnect:

1. Coolant

2. Thermostat housing from under the water pump housing.


Loosen but don't remove the bolts holding the pulley to the water pump.

Remove or disconnect:

Timing belt cover.

Alternator and/or steering pump as required to remove the water pump drive belt.

Water pump pulley. On some vehicles, the crankshaft pulley must also be removed by removing the bolts holding the pulley to the timing belt sprocket.

Water pump from its housing.


To install:


Be sure to clean the housing before installing the new gasket. Install the pump into the housing. Pump-to-housing bolts: 84 inch lbs. (10 Nm).

Install the water pump drive pulley. Bolts: 15 ft. lbs. (20 Nm). Install crankshaft drive pulley. Bolts: 15 ft. lbs. (20 Nm).

Adjust drive belt tension and install the thermostat and housing. Bolts: 84 inch lbs. (10 Nm).



archaeology_93.jpg

Fig. Water pump and thermostat housing-2.0L (ABA) engine

1. Before servicing the vehicle, refer to the Precautions Section.

2. Remove or disconnect:

Coolant

Thermostat housing from under the water pump housing.



3. Loosen but don't remove the bolts holding the pulley to the water pump.

4. Remove or disconnect:

Timing belt cover.

Alternator and/or steering pump as required to remove the water pump drive belt.

Water pump pulley. On some vehicles, the crankshaft pulley must also be removed by removing the bolts holding the pulley to the timing belt sprocket.

Water pump from its housing. Refer to figure of ABA engine's water pump above.

To install:

1. Be sure to clean the housing before installing the new gasket. Install the pump into the housing. Pump-to-housing bolts: 84 inch lbs. (10 Nm).

2. Install the water pump drive pulley. Bolts: 15 ft. lbs. (20 Nm). Install crankshaft drive pulley. Bolts: 15 ft. lbs. (20 Nm).

3. Adjust drive belt tension and install the thermostat and housing. Bolts: 84 inch lbs. (10 Nm).



2.0L (Aeg/Avh/Azg/Bdc/Bev/Bgd) Engine


1. Before servicing the vehicle, refer to the Precautions Section.

2. Remove or disconnect:

Negative battery cable.

Coolant.

Accessory drive belt and tensioner.

Upper and center timing belt covers.



3. Position the engine so that the No. 1 cylinder is at TDC.
WARNING
Cover the timing belt to protect it from being contaminated with coolant.


4. Loosen the timing belt tension and slide the belt off the water pump sprocket.

5. Remove or disconnect:

Timing belt guard (2) mounting bolt (1), if equipped.

Water pump mounting bolts (5), then the water pump (4).

O-ring (3) and clean the seating area.


To install:



archaeology_94.jpg



Fig. Exploded view of the water pump mounting-2.0L (AEG/AVH/AZG/BDF) engine

1. Install or connect:

O-ring, moistened with coolant.

Water pump so that the plug in the housing faces downward. Mounting bolts: 11 ft. lbs. (15 Nm).

Timing belt guard, if equipped. Mounting bolt: 15 ft. lbs. (20 Nm).

Timing belt.

Upper and center timing belt covers.

Accessory drive belt tensioner. Mounting bolt: 18 ft. lbs. (25 Nm).

Accessory drive belt.

Coolant.

Negative battery cable.



2. Check and clear any DTCs, then match the ECM to the TCM.


2.0L (Aeg/Avh/Azg/Bdf) Engine


1. Before servicing the vehicle, refer to the Precautions section.

2. Remove or disconnect:
1. Negative battery cable.

2. Coolant.

3. Accessory drive belt and tensioner.

4. Upper and center timing belt covers.


3. Position the engine so that the No. 1 cylinder is at TDC.

WARNING
Cover the timing belt to protect it from being contaminated with coolant.

Loosen the timing belt tension and slide the belt off the water pump sprocket.

Remove or disconnect:

1. Timing belt guard (2) mounting bolt (1).

2. Water pump mounting bolts (5), then the water pump (4).

3. O-ring (3) and clean the seating area.


To install:



archaeology_95.jpg


Fig. Exploded view of the water pump mounting-2.0L (AEG/AVH/AZG/BDF) engine


Install or connect:

1. O-ring, moistened with coolant.

2. Water pump so that the plug in the housing faces downward. Mounting bolts: 11 ft. lbs. (15 Nm).

3. Timing belt guard. Mounting bolt: 15 ft. lbs. (20 Nm).

4. Timing belt.

5. Upper and center timing belt covers.

6. Accessory drive belt tensioner. Mounting bolt: 18 ft. lbs. (25 Nm).

7. Accessory drive belt.

8. Coolant.

9. Negative battery cable.


Check and clear any DTCs, then match the ECM to the TCM.

Sep 13, 2011 | 2001 Volkswagen Cabrio

1 Answer

Cylinder 1 is misfiring. The plugs and wires have been replaced.


Misfire condition can cause by few items.

1) mis-gap / worn / damaged plug.
One Hyundia and small displacement engine,it can also be loose plug.

2) oil leak / vapor covering the cermaic portion of the plug.

3) clogged air flter. // change interval for small car is 12,000 to 18,000 miles.

4) clogged PCV on // 140,000 or higher mile vehicle

5) worn valve cyclinder // 160,000 miles +

6) worn timing belt with an old water pump //// 140,000 miles+


Please reply with the currrent odomenter reading and recent repair record.

Feb 03, 2011 | Hyundai Motor 2004 Accent

1 Answer

MY ACCORD HAS 119,000 MILES ON IT AND I HAD THIS WORK DONE ON THE CAR. 1. TUNE UP 2. RAIDIATOR FLUSH 3. TRANS SERVICE 4. BELTS CHANGED THE CAR RUNS GREAT BUT I AM BEING TOLD TO HAVE THE TIMING BELT CHANGED...


well that is how I always sell a timing belt job also. The water pump is driven by the timing belt and it is very labor intensive to replace. I always replace the water pump also because you have to remove the timing belt to replace. I have had people refuse the water pump, and have to spend the same labor dollars a few months later when the pump went out. Even if not leaking it is always good insurance to replace the pump with the timing belt but is not a must just good idea.

Nov 12, 2010 | 2004 Honda Accord

1 Answer

Timing chain needs to be replaced every 100,000 miles? And what the major parts needing to be replaced for the 100,000 mile mark?


You will have a timing belt on your vehicle that is usually replaced along with the water pump. At 100K miles i would do the following: 1. Timing Belt and Water pump replacement and Serpentine Drive Belt replacement. I suggest replacing all the cooling system hoses, replace the thermostat & radiator cap and flush the radiator since the cooing system will be drained and fill with new coolant/water mixture. 2. Check the motor mounts and replace if necessary. 3. Replace the spark plugs and wires. 3. Check the cv joints for broken or cracked boots and replace if necessary. 4.Have the transmission/transaxle serviced and filled with new transmission fluid. (This should be done every 30k miles) 5. I also suggest oil and filter replacement, air filter replacement, have the brakes checked and the tires rotated. It is a good idea to have the thottle body cleaned and the fuel filter replaced also. All of these should be done if they have not been done already. I believe in preventative maintenance and if you can catch problems before they get too serious you can save yourself a lot of time and money. I hope this helps. Please rate me on my answer.

Jul 09, 2010 | 2003 Toyota Corolla

1 Answer

Starts fine & stops in 3-5 minutes or driving in 1-3 miles.


Did you replaced your whole distributor or just the cap and the rotor? Have you check the pressure on you fuel line it could be your fuel pump.

May 16, 2010 | 1993 Plymouth Colt Vista

1 Answer

Where is the water pump on a 2000 hyundai 2.5 motor


Your water pump is located underneath the timing cover, your timing belt runs the water pump, when replacing water pump replace timing belt also, belt should be replaced every 50,000 miles

Feb 07, 2010 | 2000 Hyundai Sonata

2 Answers

Timimg belt on on 2003 megane


no i dont think so but you can always get a 2nd opinion on the matter and a second cost amount...

Jan 12, 2009 | 2005 Renault 18I

2 Answers

I need instructions on replacing the timing belt


1. Remove the Alternator Belt.
2. Remove the Water Pump Pulley
3. Remove the Air Conditioner Belt and Power Steering Belt.
4. Remove the Crankshaft Pulley.
5. Remove the timing belt cover
6. Remove the timing belt tensioner pulley.
7. Remove the Timing Belt.
8. (If Replacing) Remove Idler Pulley.
Installation is reverse of removal. Keep a close eye on the timing marks on the cam sprockets to make sure you don't knock anything out of whack.

I would strongly recommend replacing the water pump while you are replacing the timing belt. (The water pump usually comes in the timing belt kit.) Otherwise you are going to have to do this all over again when your water pump goes out. Good Luck.

Nov 10, 2008 | 2004 Hyundai Tiburon

Not finding what you are looking for?
1996 Saturn SL Logo

141 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...