Question about Buick Skylark

1 Answer

Automotive stainless steel repair

Where may I find a reputable, affordable place where I can get the stainless steel side moldings on my 1966 Buick Skylark repaired? Someone in the past has used sheet metal screws to attach the moldings when the original clips failed. I cannot seem to find where I can get them repaired or replaced. The bumpers also have to be straightened and rechromed. Those I can find somewhere hopefully. The side moldings are the real problem. Thank you, Tom

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Buick Master
  • 6,674 Answers

Check for electroplating business. We have one in our area that does bumpers or whatever needs chrome re-done. contact a local car club too if you any in your area, they'd most likely have all those number & connections for you. Even a local bodyshop should be of assistance.

Posted on Dec 10, 2008

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Do the ignition switch an door locks take the same key in a 66 Buick lesabre

Kevin, Ignition and door locks are different cut keys on 1966 Buick. the ignition key was square/octagon shape and the door lock/trunk key were oval.
Below are links that show the difference.
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Buick Skylark Locks Hardware eBay
Door Lock 1965 66 Buick CARS LLC
1966 BUICK LESABRE 5 6L 340cid V8 Door Lock Cylinder RockAuto

Jun 22, 2016 | Buick Cars & Trucks

1 Answer

How do I replace 1/4 pamel ornament on 1966 mustang

Remove rear seat. Remove arm rest. Remove side panel. Remove 3 (or 4) nuts that hold the side ornament in place. Hope this helps.

Mar 11, 2015 | 1966 Ford Mustang

1 Answer

How do I remove the tailgate on 1966 ford f100

un hook safety cables , lower gate till you see an opening on right side that holds gate ( a steel cup with one side missing ) lift right side past opening , lift out ,& up and pull to right to remove from left side.

Oct 12, 2014 | 1981 Ford F 100

1 Answer


Depending on the clip, there were special tools made to release the clip from the molding. The tool slides under the molding and you turn it to release. The clips are usually screwed to the metal surface, or snap into a hole.

Sep 22, 2014 | Ford Fairlane Cars & Trucks

1 Answer

What is the stainless steel line called around the engine of a 2000 buick century?

could be for your air conditioning those are usually stainless

Apr 19, 2013 | 2000 Buick Century

1 Answer

2000 Toyota RAV4 side door emblems How do I remove, then replace [higher] RAV4 emblem on side doors to allow fitting of body protection mouldings.

Use an automotive heat gun set to low setting and gently pry the old molding off, then locate an automotive paint/body shop supply store and buy a roll of the special molding double sided tape to put it back on, you will have to buy a whole roll , it will be pricey.

May 18, 2012 | 2000 Toyota RAV4

1 Answer

04 lasabre where is the feul filter located

The inline filter is in the rocker panel area(believe on the driver's side).It's approx. 3 inches around and 5 inches long,stainless steel.

May 11, 2012 | 2004 Buick LeSabre

2 Answers

I think my wheel bearing needs replaced in front driver side. could this be done in my driveway?

it depends on if it is a pressed bearing or not and if u need some heat to get it out i rec a shop.

Jan 26, 2011 | 2006 Buick Rainier

1 Answer

1966 mustang

Get a pittman arm puller. They are sold at just about any parts or automotive place, thats going to be the easiest way to get the pitman arm off. and the safest way. Not an expensive tool.

Mar 23, 2009 | 1966 Ford Mustang

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

88 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts


Level 3 Expert

64052 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides