Question about 1997 Audi A4

1 Answer

I have a 2005 Hyundai Elantra which just started jumping hard into 2nd and 3rd gears especially is I am accelerating it does have over 100 thousand miles but I have kept up with the oil changes pretty regularly I have not done it however for the last 3 thousand mile visit. Could this be the problem? It's really clunking sometimes.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 45 Answers

Replace the transmission box bushes

Posted on Jan 16, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Dodge Ram 3500 skips from 1st to 3rd gear, had rebuild after still the same issue. Any advice?


Governor pressure controls the 1st and 2nd shifts. After that is the 3 and 4 solenoids. you would need to look at the pressure when driving(takes a scanner). pressure is 20 to 30 PSI from 1st to 2nd, depends on acceleration. After that the pressure will jump to 100+ psi. Did you replace the governor solenoid and sensor? They are on the passenger side of the transmission and sit in a block that detaches from the valve body.

Sep 22, 2016 | 2005 Dodge Ram 3500

1 Answer

I have a 2012 Hyundai Elantra. It's shifting hard


try gear oil level / selectors / thrust bearing / presure plate

Sep 02, 2012 | Cars & Trucks

1 Answer

2005 Hyundai Santa Fe. Car shifts very hard from 2nd to 3rd gear. Along with the hard shifting it jumps/jerks when it engages into 3rd gear.when downshifting Very hard shift into lower gears and car slows...


First thing ... pull the dipstick and check the oil. It should be bright pink or red, if it's brown or black and smells bad your oil has never been changed. Drain as much as you can, measure how much came out and replace it with synthetic compatible oil. Start the car and let is run for a few minutes and shift the gears a few times ... then take it for about a 10 mile ride to circulate the oil, stop and go now and then so it will shift through all the gears. You could also add about half a quart of Lucas Transmission Fix.

Jun 03, 2017 | Cars & Trucks

1 Answer

Suto trasmission when it shifts from 2nd to third


sounds like the symptom of a bad clutch, might need adjustment at local repair service.

Dec 22, 2009 | 2001 Hyundai Elantra

1 Answer

Can't get car in or out of gear


Throwout bearing will need to be replaced most likely. Otherwise cluctch plate or fork may have stuck

Aug 06, 2009 | Hyundai Motor 2002 Elantra

Not finding what you are looking for?
1997 Audi A4 Logo

180 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

yadayada
yadayada

Level 3 Expert

77499 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14398 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...