Question about 2001 Ford Windstar

1 Answer

My check engine lights on and flashing code says missfire on c3

New plugs and wires can u help

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Could be a bad coil pack

Posted on Dec 22, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1998 Mercury Grand Marquis rough idle, smelling gas first few minutes after I start my car. My car is also flashing engine light sporadically and losing acceleration.I recently changed spark...


flashing light most always means missfire.
could even be crossed wires.to the plugs.
you really need a code reader and find the trouble code .
but in the mean time make sure the firing order is correct.
good luck .gary

Oct 27, 2013 | 2002 Subaru Outback

1 Answer

Check engine light on and flashing, car shaking, all of a sudden


you have a bad engine missfire. a flashing check engine light means you are in danger of damaging your catylitic converter and you should scan the car. most causes of missfires are plug wires and or coil pack.

Dec 12, 2011 | 2001 Chevrolet Cavalier

2 Answers

Check engine light flashing runs rough not firing on all cylinder2000 lincoln navigator with large triton engine Hooked up diagnnostic and it said 1. system too lean bank #2 2. Unable to bleed up fuel tank...


you may try your rotor button and distributor cap. and spark plug wires. try your map sensor also they tend to cause a lot of misfiring if they go bad.hope this helps.

Apr 20, 2010 | Lincoln Navigator Cars & Trucks

1 Answer

My check Engine light stays on and begins to blink when I accelerate. What could be the cause of this?


you need to find out what the code is. usually when the light is flashing it means that you have a missfire like a plug or wire breaking down or a coil breaking down. auto zone will scan your computer for free.hope this helps. please leave comment.

Mar 26, 2010 | 2004 Acura TL

2 Answers

I have a missfire code on the check engine light. 1997 honda prel


Find out which cylinder is missfiring by using an inductive timing light to check each plug wire for spark. If you find a dead wire you should replace the all the wires and spark plugs. If you don't find a dead wire check the distributor cap. You could have a broken contact or a crack which might cause a loss of spark at one cylinder.

Honda wires are much better than their aftermarket counterparts so don't skimp there.

I hope this helps. Good luck and be careful!

Dec 11, 2009 | 1997 Honda Prelude

1 Answer

Servie Engine Soon light is on and car is shaking when on


the check engine light has come on and is setting a code for a missfire detected.
have the sparkplugs and plug wires replaced.

this should cause the miss to go away and the check engine light will not come back on after being reset for free at autozone.

just resting the check light will not fix the missfire and it will come back on.

only have it reset after the service is done.

hope this helps
thank you
jm

Aug 10, 2009 | 2005 Buick Rendezvous

1 Answer

Check engine flashing


Your engine light is flashing because the engine computer is picking up a excessive missfire from the engine (bad spark plug,bad coil,bad plug wire) check to see why its skipping

Jun 05, 2009 | 2001 Mazda MPV

1 Answer

My check engine light is on and flashing the code thats comes up is missfire on cylender 3.


check #3 cylinder coil for spark with plug wire attached and unattached also check the plug to see if it is fouled out

Dec 09, 2008 | 2001 Ford Windstar

Not finding what you are looking for?
2001 Ford Windstar Logo

Related Topics:

67 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

70347 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Ron Lankford

Level 3 Expert

5386 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...