Question about 2008 Toyota 4Runner

1 Answer

1998 4runner needs new turn signal switch.

Do I need to remove the steering wheel?

Posted by on

  • Jeremiah Sumner
    Jeremiah Sumner Feb 11, 2013

    Hey there how did this turn out? Were you able to get the 2 steering column covers off without removing the steering wheel??

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Toyota Master
  • 64,204 Answers

U do not need to pull the wheel

Posted on Dec 09, 2008

  • Jeremiah Sumner
    Jeremiah Sumner Feb 11, 2013

    Are you able to expand on this at all? My 1998 4Runner has 2 screws behind the steering wheel that appear to be holding the 2 plastic column covers together.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How would I go about replacing the turn signal switch on a 92 Cutlass Supreme S?


Well two major tools you will need,a steering wheel puller ,and a lock plate remover.Remove the horn button(carefully disconnect the horn button wire) pad,screws on back side of steering wheel,then remove large nut holding steering wheel(but first mark steering wheel to be sure you are able to line it back up properly),then use the steering wheel puller,after steering wheel is removed install lock plate remover and compress lock plate down ,and remove C clip pull upwards out of groove,remove puller and C clip and remove horn rotor and lock plate,and you are at the turn signal switch three screws hold the part,remove emergency switch with phillups screw driver and the turn signal lever. remove bezel under dash (where ur knees would be,and disconnect the long flat plug and remove it from its holder and remove turn signal switch.

Oct 25, 2013 | Oldsmobile Cutlass Supreme Cars & Trucks

1 Answer

69 firebird turn signal switch does not cancel, need blow up of internal parts in column


You need to replace turn sinal switch its not hard remove center of steering wheel (horn button) remove steering wheel bolt with steering wheel puller pull wheel off remove turn signal handle three screws and emergency button, under dash on right side of steering colume disconect turn signal wires tape a long wire to the end of connector pull turn signal wires out with out pulling tape wire out so you can tape new turn signal wire connector to wire so you can pull it back through

Jun 29, 2011 | Pontiac Firebird Cars & Trucks

1 Answer

My 1995 f-150 ford needs a new key ingintion lock, i can start the truck without the key. is this a easy fix?


To remove the ignition lock:
CAUTION
You must remove the steering wheel when replacing the ignition lock. On vehicles with a Supplemental Inflatable Restraint (SIR) system, you must temporarily disable the SIR system and remove the inflator module when removing the steering wheel. Leaving the SIR system on could result in deployment of the air bag and possible personal injury.
  • Disconnect the negative battery cable, and remove the steering wheel.
  • Remove the bumper and the carrier snapring retainer from the steering shaft.
  • Use a lock plate compressor screw tool to install the lock plate compressor screw in the upper steering shaft. To keep the shaft from telescoping, tighten it to 40 inch lbs.
  • Using the lock plate compressor tool, install on the upper steering shaft, tighten it to depress the shaft lock. Remove the shaft lock retainer, the compressor tool and the steering shaft lock.
  • Remove the turn signal canceling cam assembly. Put the turn signal switch in the "N" position and remove the upper bearing spring.
  • Position the turn signal switch so the mounting screws can be removed through the holes in the switch and remove the turn signal lever.
  • Remove the turn signal switch-to-steering column screws and lift the turn signal switch. Remove the wire protector and disconnect the turn signal switch connector.
  • Use a terminal remover tool to disconnect the buzzer switch wires from the turn signal switch connector. Remove the buzzer switch assembly with needle-nose pliers.
  • Place the lock cylinder in the ACC position, then remove the lock retaining screw and the lock cylinder set.
  • To install the new cylinder lock, reverse the removal procedures.
  • Tighten the lock retaining screw to 22 inch lbs., the turn signal switch screws to 59 inch lbs. and turn the turn signal lever screw to 53 inch lbs.
  • As part of the final replacement procedures, check the operation of the switches and the steering column.

Aug 10, 2010 | 1995 Ford F150 Styleside Regular Cab

1 Answer

How do you remove the ignition lock cylinder on a 1991 chevy cavalier


The ignition switch removal and installation procedure is given in , under steering, because the steering wheel must be removed for access to the ignition switch.

To remove the ignition lock:
CAUTION
You must remove the steering wheel when replacing the ignition lock. On vehicles with a Supplemental Inflatable Restraint (SIR) system, you must temporarily disable the SIR system and remove the inflator module when removing the steering wheel. Leaving the SIR system on could result in deployment of the air bag and possible personal injury.
  • Disconnect the negative battery cable, and remove the steering wheel.
  • Remove the bumper and the carrier snapring retainer from the steering shaft.
  • Use a lock plate compressor screw tool to install the lock plate compressor screw in the upper steering shaft. To keep the shaft from telescoping, tighten it to 40 inch lbs.
  • Using the lock plate compressor tool, install on the upper steering shaft, tighten it to depress the shaft lock. Remove the shaft lock retainer, the compressor tool and the steering shaft lock.
  • Remove the turn signal canceling cam assembly. Put the turn signal switch in the "N" position and remove the upper bearing spring.
  • Position the turn signal switch so the mounting screws can be removed through the holes in the switch and remove the turn signal lever.
  • Remove the turn signal switch-to-steering column screws and lift the turn signal switch. Remove the wire protector and disconnect the turn signal switch connector.
  • Use a terminal remover tool to disconnect the buzzer switch wires from the turn signal switch connector. Remove the buzzer switch assembly with needle-nose pliers.
  • Place the lock cylinder in the ACC position, then remove the lock retaining screw and the lock cylinder set.
  • To install the new cylinder lock, reverse the removal procedures.
  • Tighten the lock retaining screw to 22 inch lbs., the turn signal switch screws to 59 inch lbs. and turn the turn signal lever screw to 53 inch lbs.
  • As part of the final replacement procedures, check the operation of the switches and the steering column.

3026ee6.gif

The steering wheel is splined to the steering column and held in place by a nut. Courtesy of General Motors Corporation - Service Operations.

Hope this helps (remember rated and comment this).

Mar 22, 2010 | 1991 Chevrolet Cavalier

3 Answers

I have a 87 blazer s10... the turnswitch /wiper/highbeam switch is broken and is shorting out my brakelights ..i cant seem to get to it.. took the steering weel off but ..?


Unfortunately there are some special tools required you will need to get to the turn-signal switch. Below is the procedure for replacing the turn-signal switch. Generally you can rent the puller from a local auto parts jobber or you can purchase one.
Good luck, let me know how it goes.
Regards,

Many vehicles use a turn signal switch that is separate from the multifunction switch. The steering wheel will have to be removed to gain access to the turn signal switch on these vehicles. The following procedure is a common method of turn signal switch replacement:
  • Place the fender covers on the fenders.
  • Disconnect the negative battery cable.
  • Remove the steering column trim.
  • Remove the horn pad from the steering wheel.
f_aee_cc14.28.jpg Steering wheel attachment. Courtesy of General Motors Corporation, Service Technology Group.
  • Remove the steering wheel and horn collar.
  • Use a suitable puller to remove the steering wheel.
  • With a suitable compressor, compress the preload spring to the lock plate. Compress the spring only enough to remove the snap ring.
f_aee_cc14.29.jpg To remove the snap ring, use the compressing tool to relieve the pressure against the snap ring. Courtesy of General Motors Corporation, Service Technology Group.
  • Use a pick and a small flat blade screwdriver to remove the snap ring.
  • Remove the lock plate, horn contact carrier, and spring.
  • Remove the bolts at the upper steering column support and the upper mounting bracket from the column.
  • Disconnect the turn signal wiring connector.
  • Wrap tape around the wire and connector.
  • Remove the hazard warning knob from the column.
  • Remove the switch retaining screws and remove the switch.
f_aee_cc14.30.jpg Remove the turn signal switch from the column. Courtesy of Chrysler Corporation.
  • Replace the switch and reverse these procedures for reinstallation.

Sep 19, 2009 | 1987 Chevrolet Blazer

1 Answer

96 Cavailer ignition cylinder problem


To remove the ignition lock:
CAUTION
You must remove the steering wheel when replacing the ignition lock. On vehicles with a Supplemental Inflatable Restraint (SIR) system, you must temporarily disable the SIR system and remove the inflator module when removing the steering wheel. Leaving the SIR system on could result in deployment of the air bag and possible personal injury.
  • Disconnect the negative battery cable, and remove the steering wheel.
  • Remove the bumper and the carrier snapring retainer from the steering shaft.
  • Use a lock plate compressor screw tool to install the lock plate compressor screw in the upper steering shaft. To keep the shaft from telescoping, tighten it to 40 inch lbs.
  • Using the lock plate compressor tool, install on the upper steering shaft, tighten it to depress the shaft lock. Remove the shaft lock retainer, the compressor tool and the steering shaft lock.
  • Remove the turn signal canceling cam assembly. Put the turn signal switch in the "N" position and remove the upper bearing spring.
  • Position the turn signal switch so the mounting screws can be removed through the holes in the switch and remove the turn signal lever.
  • Remove the turn signal switch-to-steering column screws and lift the turn signal switch. Remove the wire protector and disconnect the turn signal switch connector.
  • Use a terminal remover tool to disconnect the buzzer switch wires from the turn signal switch connector. Remove the buzzer switch assembly with needle-nose pliers.
  • Place the lock cylinder in the ACC position, then remove the lock retaining screw and the lock cylinder set.
  • To install the new cylinder lock, reverse the removal procedures.
  • Tighten the lock retaining screw to 22 inch lbs., the turn signal switch screws to 59 inch lbs. and turn the turn signal lever screw to 53 inch lbs.
  • As part of the final replacement procedures, check the operation of the switches and the steering column.
f42-11.gif The steering wheel is splined to the steering column and held in place by a nut. Courtesy of General Motors Corporation - Service Operations. gl
G

Jun 24, 2009 | 1996 Chevrolet Cavalier

1 Answer

Changing turn signal switch 1986 lincoln town car.


Get a manual like chiltons or haynes to guide you through this one...Air bag needs to be disabled and yes, wheel needs to be removed.You will need a wheel puller and a tool to remove the steering lock plate. The arm either unscrews from or is screwed to the switch...either way, it's removable.

May 29, 2009 | 1986 Lincoln Town Car

1 Answer

1992 cavalier ignition switch and key assembly


The following procedure is "generic" for replacing the lock cylinder. There are a couple of specialized tools you will need and saftey precautions concerning the air bag system.
Take a look and let me know if you wish to tackle the job.
Regards,
To remove the ignition lock:
CAUTION You must remove the steering wheel when replacing the ignition lock. On vehicles with a Supplemental Inflatable Restraint (SIR) system, you must temporarily disable the SIR system and remove the inflator module when removing the steering wheel. Leaving the SIR system on could result in deployment of the air bag and possible personal injury.

  • Disconnect the negative battery cable, and remove the steering wheel.
  • Remove the bumper and the carrier snapring retainer from the steering shaft.
  • Use a lock plate compressor screw tool to install the lock plate compressor screw in the upper steering shaft. To keep the shaft from telescoping, tighten it to 40 inch lbs.
  • Using the lock plate compressor tool, install on the upper steering shaft, tighten it to depress the shaft lock. Remove the shaft lock retainer, the compressor tool and the steering shaft lock.
  • Remove the turn signal canceling cam assembly. Put the turn signal switch in the "N" position and remove the upper bearing spring.
  • Position the turn signal switch so the mounting screws can be removed through the holes in the switch and remove the turn signal lever.
  • Remove the turn signal switch-to-steering column screws and lift the turn signal switch. Remove the wire protector and disconnect the turn signal switch connector.
  • Use a terminal remover tool to disconnect the buzzer switch wires from the turn signal switch connector. Remove the buzzer switch assembly with needle-nose pliers.
  • Place the lock cylinder in the ACC position, then remove the lock retaining screw and the lock cylinder set.
  • To install the new cylinder lock, reverse the removal procedures.
  • Tighten the lock retaining screw to 22 inch lbs., the turn signal switch screws to 59 inch lbs. and turn the turn signal lever screw to 53 inch lbs.
  • As part of the final replacement procedures, check the operation of the switches and the steering column.

Mar 04, 2009 | 1992 Chevrolet Cavalier

1 Answer

ReplacingTurn Switch


1. You are going to need a steering wheel puller.
2. You remove the steering wheel center.

3. you remove the large steering column nut, then install steering wheel puller to remove the steering wheel. It is necessary to mark the shaft to the steering wheel so that it will go back in the same position.

Once the steering wheel is removed, you can see the turn signal switch. There is one center screw that holds the turn signal switch inside the steering wheel hub.

Once the screw is removed the signal can be lifted up over the steering wheel shaft.

Now leaving that, go underneather the dash area and remove the smallpanel around the steering wheel shaft. There you will find a large electrical connector with all the wires that are used in the steering column. This connector can either be fed up thru the column or by disconnecting all of the wires and feeding them up through the column.

this will remove the old switch. The new switch and its wiring harness must now be fed back down the steering column and then reconnected to the large electrical connector.

Now re-install the new switch, screw the turn signal stem back into the switch assembly and the re-install the steering wheel, according to the aligments marks you made, otherwise your steering wheel will be off centered. Tighten down steering wheel center nut, and other panels. Check operation of switch.
Factory manuel gives mechanics 1 hour to do this, but it cam take up to 4 hours.
Bill

Nov 23, 2008 | 1999 Ford F250 Regular Cab

1 Answer

Turn signal switch


'm not sure but I'll put in my 2 cents worth.

I changed a turn signal switch on an older model and it wasn't too difficult. First you have to remove the horn button or top center piece of the steering wheel. There should be screws from the bottom side that you remove to do this. Once you get that off there is simply a large nut in the center than needs to be removed that holds the steering wheel on. [I did not need any sort of steering wheel puller.] Once the steering wheel is off you'll see how the turn signal switch is attached. its simply a matter of disconnecting the wires and removing screws and then putting everything back together. Make sure you get the steering wheel properly positioned. Before you start simply make sure the wheel is positioned in the straight ahead position.

Jun 23, 2008 | 1996 Ford Taurus

Not finding what you are looking for?
Cars & Trucks Logo

125 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

64052 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...