Question about 1995 Geo Metro

1 Answer

1995 GEO METRO BLOWER MOTER REPLACE

I HAVE A 95 METRO THE AC AND AIR WORKS ,BUT THE FAN ON HIGH SEEMS TO WORK THE AIR IN THE VENTS IS NOT STRONG.SEEMS LIKE A RESTRICTION OF SOME KIND.IF I REMOVE THE BLOWER MAYBE I CAN VACUMTHE VENTS,THE REAR BOLT FOR THE MOTRE IS IMPOSSIBLE TO GET AT,HOW DO I DO THIS?

Posted by on

  • 1 more comment 
  • vada2008nc Dec 09, 2008

    where is the resister located?

  • yadayada
    yadayada May 11, 2010

    near the blower motor.

  • yadayada
    yadayada May 11, 2010

    U need to replace the blower fan motor speed control resistor, the fan motor is not the problem.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 51 Answers

Yes, the speed control resistor is a possible culprit. There are other possibilities though. The motor itself might be wearing out. Bearings could be going bad and binding, or the motor itself could be. Usually when a speed control resistor goes, the particular speed setting that portion controls goes out completely, not just slows down. Most automotive blower motors have an independent resistor coil for each speed that you can select. If one of them goes, you lose that speed and keep the others. If you replace the resistor and continue to have a problem, you might want to remove the motor assembly completely and have it bench tested.

Posted on Feb 06, 2009

  • Randall LaClaire Feb 09, 2009

    As for the location of the resistor, yes they are usually near the blower motor. Usually you will find them under the dash in newer vehicles with a black plastic cover over them. They are usually copper coils (look like a miniature coil spring). Sometimes you will find them in the engine compartment, on the firewall, again under cover.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why is the blower not blow strong air out i put new moter in but it still does not blow good


do all of the fan speeds work? if not you need to replace the blower motor resister. If all of the fan speeds work then you need to clean or replace your in cabin air filter. When this filter gets clogged you get very little air flow from your vents. Instructions for your cabin air filter service are in your owner's manual

Sep 19, 2010 | 1999 Lincoln Town Car

1 Answer

Yes i have a 95 geo metro its a four door it over heats while idling when its driving its fine change theremostat its still doing it fan does run not sure why its doing that think fan is not turning on in...


Your on the right track, try jumping the sensor so the fan stays on. If that works replace the sensor.
If it does not hook the fan up to the battery direct to see if it works.

Aug 05, 2010 | 1995 Geo Metro

1 Answer

The fan for the heater/vent/AC is stuck on high and remains running when the vehicle is shut off. I am able to switch from vent to heater to AC to defrost, but the fan always stays on high. This is a 95...


Does this have auto temp control where you set the temp number or does it have a knob you set 1-5. I'll bet you have auto temp. and you need to replace the blower control module under the hood.

Jun 05, 2010 | 1995 Buick LeSabre

1 Answer

95 Olds 88 AC/ heater fan does not work. Prior to this it worked off and on, also worked on some speeds, and not on others.


there should be a relay switch under the hood for the blower moter that might have gone bad

Aug 05, 2009 | 1995 Oldsmobile 88

1 Answer

1995 geo metro blower moter speed resister


before you start you have to disconnect negative battery terminal. Remove glovebox.Remove harness connectors from ECM (electronic control module). To access blower motor resistor, remove ECM and disconnect blower resistor (remove screw and resistor mounted on heater case. To install reverse removal procedure.
Hope it helps

Dec 09, 2008 | 1995 Geo Metro

1 Answer

Need location of blower motor resister on 1995 geo metro


Have you ruled out a blend dorr issue yet?

Dec 09, 2008 | 1995 Geo Metro

1 Answer

High-beams not working


U are going to have to replace the mulitfunction switch if the bulbs are not the problem

Nov 16, 2008 | 1995 Geo Metro

Not finding what you are looking for?
1995 Geo Metro Logo

529 people viewed this question

Ask a Question

Usually answered in minutes!

Top Geo Experts

yadayada
yadayada

Level 3 Expert

63801 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Geo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...