Question about 1997 Dodge Ram 2500 Club Cab

2 Answers

2003 Dodge 4x4 2500 drive shaft popping when in 4x4

I have a cummins that you engage the 4x4 on the floor but it pops loudly and slips. It still works but not good and sounds horrible.

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

I had a similar problem on my 99 dodge cummins with the same t case i tore it apart to find theres plastic bushings on the shift forks now when they were just a little bit they wont work that solved my problem only place to buy them bushings is at ur local dodge dealer

Posted on Nov 02, 2012

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

Sounds like the acuator on the axle isn't locking the axels together and allowing them to slip you can check it by removing the actuator and looking at the collar and splines on the shafts.

Posted on Dec 11, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Key doesn't start it but can pop the clutch


check the safety switch . there is a switch that if the clutch petal isn't all the way down to the floor it will not permit the ignition to engage the starter. the switch is either on the floor where the pedal will contact it or up along the pedal shaft. its there. if that doesn't fix it, check the wires to the starter. and lastly the ignition switch itself could be going bad.

Dec 22, 2013 | 1999 Dodge Neon

1 Answer

4wd messed up in dodge 1500


inspect for worn components from output of transfer case to front diff input. If everything is tight and solid from those two points, everything else points to being transfercase internals. Make sure your actuator isn't faulty causing a "4x4 to 2x4 shift on/off"

Dec 13, 2013 | Dodge Cars & Trucks

1 Answer

2003 Isuzu Rodeo right front tire making noise when going over speed bump and loud popping noise when turning to the left


Two faults here ,one is the drive shaft universal on the end of the drive shaft and the other noise ? well could be anything and without a good look and a wiggle with a 4ft crow bar i honestly couldnt say

Jul 05, 2013 | 2003 Isuzu Rodeo

1 Answer

My air conditioner does not work on my 06 dodge 2500 5.9 l diesel. The blower motor works fine but the compressor does not engage. I've checked pressures and shows to be charged. What eles could it be?


The factory harness is known to have a voltage drop at the clutch which slips the clutch causing heat and melts the clutch coil and burns the oil out of the berrings, your next problem is going to be a siezed idler berring now the pump turns allways while the engine is running, over pressurizes pops something (mine was the evap core, under the dash), then the pump berring goes out spitting metal trash through your whole system. It all in all is a very expensive problem, replace your compressor "now" with an updated version clutch, and replace your harness to the compressor, before this $2500 problem happens to your truck then call dodge and complain! I am on my second compressor at 70k on my 2006 cummins, my compressor supplier said he sells 200 of these a month! Gee do you think its a manufacturers error???

Jul 08, 2011 | 2006 Dodge Ram 2500

1 Answer

I have a gmc sierra 1500 4wd. when I engage the 4wd and go to make a turn I hear a loud popping noise. In 2wd it does not do this. Is something wrong with the transfer case?


Alot of people are having this problem. A locked 4x4 while turning on a dry or wet surface will do this, unless it is snow or mud which allow the wheels to slip the front wheels bind and buck,clunk. Now if this is not the case then check the CV joints, jack front wheels off ground, one at a time is fine, grab wheel and wiggle all around and see if tire feels loose as it might be a bad wheel bearing hub also. I don't believe there is anything wrong with the ,transfercase. I have owned 4x4s for 31 yrs ranging from 1967 - 2003, mostly chevy (gmc) ford, and 1 dodge ram. 9 out of 10 times it is front hubs,pinion,front driveshaft. Transfercases either work or they don't,and if they don't its because it's broke and your not driving.

Feb 04, 2011 | GMC C1500 Cars & Trucks

2 Answers

How do I remove the front axle shafts in a 2003 Dodge 2500 4x4?


they just pop out. i get behind then and pop them out with a screw driver or small pry bar

Jun 04, 2009 | 2004 Dodge Ram 1500

1 Answer

02 Cummins 5.9L intermittant shut down


i had a 99 dodge cummins do about the same thing and mine was the crank position senser located behind the starter,but find out if the code matches that as senser is not cheep.hope this will help you.

Mar 17, 2009 | 2002 Dodge Ram 3500 Truck

1 Answer

Ford F150 lost 4 wheel drive 2003 FX4


Take the hubs apart, inspect them, and clean them, especially the one that you heard a clunk, something might have broke in the automatic hub lock. Make sure everthing gets put back exactly the same, or you'll have more problems. If that doesn't work, then there is something wrong somewhere in the transfer case.

Mar 15, 2009 | 1999 Ford F150 Regular Cab

Not finding what you are looking for?
Cars & Trucks Logo

542 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

63801 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...