Question about 2003 GMC Envoy

Open Question

2003 gmc envoy wheel bearing

Just had a wheel bearing replaced on 2003 gmc envoy
does anyone know the torque specs for it...thanks in advance!

Posted by on

  • Anonymous Feb 21, 2009

    I have a 2003 Envoy XL. At around 80,000km. wheel bearing started to go by 95,000 km, the LF, LR and RL bearings had to be replaced.



    No wheel bearings should fail at this stage, but 3 ?

  • Anonymous Apr 05, 2009

    i have the same problem

×

5 Suggested Answers

  • 72 Answers

SOURCE: Front Hub Bearing Torque specs to complete replacement

THE LUG NUT TORQUE SPEC - 140FT/LBS\
CALIPER MOUNT - 80FT/LBS
CALIPER BRACKET 129FT/LBS
AXLE NUT 177FT/LBS

Posted on May 09, 2009

  • 15 Answers

SOURCE: How to replace front wheel bearing on 2003 GMC ENVOY

Jack up vehicle and support with jack stands
Take off wheel
remove brake caliper
remove caliper bracket
remove rotor
remove axle retaining nut cotter pin
remove axle retaining nut
remove axle from output flange
pull axle out of vehicle
hub and bearing assembly held in by 4 bolts

installation is reverse of removal. You will need to find out the torque specs for the axle retaining nut.

Posted on Jan 31, 2009

  • 1 Answer

SOURCE: Torque specs for front wheel hub nut

112 to 174 ft lbs

Posted on Apr 04, 2009

  • 101 Answers

SOURCE: Torque setings

if it is a solid bearing do it up as tight as you can.if it is a tapered bearing do it up untill the nut is touching the bearing check the hub for play if you have got play do the nut up a bit more until the play is gone in the hub.make sure you do not over tighten the bearing or the wheel will not turn freely.the wheel needs to spin with no drag.

Posted on Jul 31, 2009

hardinfarms
  • 144 Answers

SOURCE: 2003 mazda 6 3.0 need the main bearing torque specs

I'm sending you the torque specifications for your main bearings and also your head bolts. I also sent you main bearing and cylinder head tightening sequence. I hope this will be useful2c713bf.giffce6623.gif
Main Bearings Torque specs. 40-43 Ft. Lbs.
Cylinder Head Torque specs. 56-60 Ft. Lbs.

Posted on Oct 05, 2009

Testimonial: "thank you so much! couldnt find this information anywhere, even called the local mazda dealers!"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can any one tell me where to find or what the torque specs are for a front wheel bearing axle nut is on a 2003 gmc envoy xl?


It will most likely be somewhere just over 200 lbs

Most of us have a torque wrench that goes to 150,
so you know the answer there,you can't go all the way there
& ruin the wrench

Unfortunately most repair shop ruin new wheel hub bearings
as they only use an air gun,take that away & they would have to
seek a new career path

I have never had an axle nut come loose at less than 200 lbs
& I have not used a new one as your supposed to

I think with enough googling you will find the spec
but who owns a $500 torque wrench for that
Go to 125 then use a long ratchet or bar to twick it some

Aug 27, 2013 | 2004 GMC Envoy

1 Answer

Replace left front wheel bearing on 2002 yukon 4x4 abs


Remove the axle nut. Put a punch in the fins of the rotor to keep the hub from spinning. Remove the caliper and the rotor. Unplu the abs harness. Remove the three bolts that hold the hub to the knuckle. Remove the hub/bearing from the knuckle. Reverse to install. Make sure you torque the three bolts that hold the bearing to the knuckle and the axle nut to the correct torques spec. Failure to do so will cause premature bearing failure. Also use a good quality bearing. SKF is a good brand. Let me know if you have any questions and I'll do my best to answer them. Thank you for using FixYa.com!

Feb 02, 2012 | GMC Yukon XL Cars & Trucks

1 Answer

Right front wheel speed signal missing


you may need a wheel bearing they can test the bearing with a lab scope or meter while spining the wheel

Dec 09, 2011 | 2003 GMC Envoy

1 Answer

How to assemble a front wheel bearing on a 2003 GMC Sierra 1500 4x4


The front wheel bearing is a hub and bearing assembly. To remove you will.... 1. Remove the tire 2. Remove the axle nut. You can put a punch in the fins of the rotor to keep the assembly from turning while you rmove the nut. You can can do the same thing when you torque the axle nut. 3. Remove the caliper and rotor. 4. Unplug the abs sensor if equipped. 5. Remove the three bolts that hold the hub to the knuckle. 6. Rmove the hub. If you need torque specs let me know and i'll get them for you. It is absolutely critical that you torque the axle nut to the proper spec!

Oct 08, 2011 | Cars & Trucks

1 Answer

Hello I have a 2003 gmc envoy 4wd had to replace front hub assemblies, brake rotors and brake pads. after the job was complete took it for a test drive and every thing worked fine. my wife drove it back...


sounds like the ABS kicked in while your wife was coming to a stop. This would be known as overactive ABS. It usually occurs under 5 mph while braking. It is usually caused by a speed sensor signal dropping out at slow speeds which makes the ABS module think that the wheel has locked up. It will then engage the ABS to unlock the wheel even though the wheel is turning. The brake pedal will fade and the grind of the ABS motor will be heard.

If this was an isolated incident it will be difficult to determine the source of the problem. It it becomes more frequent and predictable it will become a lot easier to figure out. Most of the time a scan tool capable of reading ABS data will be used. The vehicle will be driven while monitoring ABS wheel speed data. When the problem occurs the wheel speed on one of the wheels will drop out and then that wheel/bearing/sensor can be inspected.

Did you torque the axle nuts after installing the new hub and bearings to the proper spec?

Have you checked to see if the new bearings are still tight? with the wheel off the ground grab it at the 12 and 6 o'clock position. if there is any play than that could cause the problem.

let me know what you find or if you have any more questions.

Aug 19, 2011 | 2004 GMC Envoy

1 Answer

Proper torque for bolts on front wheel


The axle nut spec is 177 foot lbs. and the bearing to knuckle bolts spec is 133 foot lbs.

Dec 23, 2009 | 2004 GMC Yukon

2 Answers

How to replace front wheel bearing on 2003 GMC ENVOY


Jack up vehicle and support with jack stands
Take off wheel
remove brake caliper
remove caliper bracket
remove rotor
remove axle retaining nut cotter pin
remove axle retaining nut
remove axle from output flange
pull axle out of vehicle
hub and bearing assembly held in by 4 bolts

installation is reverse of removal. You will need to find out the torque specs for the axle retaining nut.

Jan 14, 2009 | 2002 GMC Envoy

Not finding what you are looking for?
2003 GMC Envoy Logo

Related Topics:

478 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

64286 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...