Question about 1994 Mazda 323

1 Answer

Timing settings My 2003 model Mazda 323 overheated and we skimmed the cylinder head fitted back, now i am setting with two problems, i need the setting diagram for the timing belt and the last one the electric fan does not come on both for the air conditioner and radiator please help. Its a 1.6 twin cam 323.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 166 Answers

You may have forgotten to plug the fan sender unit in on the right side of the head if it is plugged in it may of failed witch is not uncommon.
as for the timing there is actually some small marks on the head it self and on the cam pulleys, also on the crank sprocket and the block if you cant find them i can send you a diagram.
if you can find the sender unit on the side of the head unplug it and earth out the plug with a split pin if the fans come on bingo get a new sender
good luck

Posted on Dec 14, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the valve clearance of mazda 323 1.3 engine 2003 model


Hi
0.25 mm for inlet and exhaust valves.
set it when engine is cold
Good Luck

May 31, 2015 | 2003 Mazda 323

1 Answer

2000 mazda protege correct timing mark alignment


Presuming the timing belt has not been removed or has skipped.
If the belt is removed or skipped this is an interference engine, valves and or pistons could be damaged by turning crankshaft, seek professional help.
Turn crankshaft clockwise and align timing marks (see jpg).
Face the marks (I) and (E) of the camshaft straight up, then align the timing marks with the horizontal surface on the cylinder head.
Pulley boss position pin on the crankshaft should be facing straight up.
25327211-bog4asmiohngydsbtkv4ivhw-1-0.jpg
This is only the beginning of an involved process, 3 pages in shop manual. I recommend getting a manual, many available on line. one typical Mazda 323 Protege Repair Manual 1990 2003
insure that the manual you get has info on your engine.

Dec 18, 2014 | 2000 Mazda Protege

1 Answer

I have a t100 that keeps overheating we replaced everything from the water pump timing belt thermostat and it still overheating can you help me


Hi, did you recently skimmed the cyl-head? if so, then cyl-head is skimmed till last capacity, so you need to get the thicker cyl-head gskt. If not skimmed, remove cyl-head and skim it. it might be corroded or wapped.

Jul 20, 2014 | Cars & Trucks

2 Answers

Guys I've got a problem with a ford bantam 1.6i 2003 model rocam engine, its overheating even though the cylinder head was skim but it still overheating. please assist!


Check what head gasket was used . I suspect that an after market gasket was used. If that is the case there will be holes in the block and head thet have no matching holes in the gasket thereby causing the problem

Jan 07, 2013 | 2006 Ford Bantam 1.6i

1 Answer

2000 model mazda 323 astina cylinder head bolt torque specs


Three stages with new bolts (a must), 1st 60 pounds, then 70 pounds then final torque is 80 FT Pounds.

Feb 16, 2012 | Mazda 323 Cars & Trucks

2 Answers

1991 mazda 323 1.6 16 valves manual. the car has a rough idle, a miss. burn greyish smoke and water comes from the exhaust. it overheats quickly and the radiater loses water with no trace of where it...


You have either blown out the head gasket or cracked the cylinder head itself. You will need to remove the cylinder head and at a minimum replace the head gasket. Inspect head surface after dis-assembly to verfiy that no cracking is present.

Feb 18, 2011 | 1990 Mazda 323

1 Answer

How to replace head gasket


why are u replacing t he cylinder head gasket did it over heat or what cos it might need to be skimmed aswell as fitting new gasket and its not a job for a diy its too complicated with valve timing and head tightening set up

Apr 02, 2010 | 1994 Toyota Pickup

1 Answer

What would be the torque setting for the cylinder head of a mazda 323 familia with a b6 engine, twin cams. thanks.


Remember you have pre loaded cam gear's that have to be loaded, or it will make kinda of a lifter noise but not lifter's.
Torque
step #1 17-19 ft.lbs
step #2 additional 85-95 deg

Nov 19, 2009 | 1994 Mazda 323

1 Answer

Timing settings


you should have timing marks that are lined up on your engine. You have your crank to line up at a certain point as well as the two cams. I don't know off the top of my head where these might be for this car but you can find it in a Haynes or Chilton manual if you so desire to also learn more about your overall car and take care of this or i can find these specs and send them your way. Up to you?

Feb 28, 2009 | 1992 Mazda 323

Not finding what you are looking for?
1994 Mazda 323 Logo

391 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...