SOURCE: I have a 1991 Ford Mustang GT speedo problem
speedo inner cable sticking in the outer,take the head out and then pull the inner cable out clean it with an oily rag with a bit of gas on then oil it as you put it back in the outer casing
SOURCE: Where is the fuse box in a 1985 Ford Mustang GT convertible
the fuse box is located at the bottom of steering column cover
SOURCE: 1993 Mustang Convertible Airbag Code 24. What's wrong?
Safing Sensor Diagnostic Circuit Open Or Low Resistance In A Primary Crash Sensor.
Each primary crash sensor has an internal resistor. The diagnostic monitor uses the resistor in the primary crash sensors in combination with the two resistors inside the diagnostic monitor to create a tightly controlled diagnostic voltage at Pin 11 (Circuit 614, GY/O). The primary crash sensors are tied together inside the diagnostic monitor at Pins 17 (Circuit 617, PK/O), 18 (Circuit 619, PK/W) and 19 (Circuit 621, W/Y). Therefore, the resistors in the sensors are connected in parallel. The parallel combination of all three sensor resistors should be equal to 393 ohms. The resistance of each sensor should be 1180 (± 20 ohms) ohms.
The resistors inside the diagnostic monitor are connected to Pins 11 (Circuit 614, GY/O) and 12 (Circuit 623, P/W) and are equal in value. Note that Circuits 614 and 623 are tied together inside the safing sensor. Therefore, the two resistors inside the diagnostic monitor are connected in parallel and will function the same as one resistor of half the original value. Current flows from Pins 1 and 6 through the resistors, out to Circuits 614 (GY/O) and 623 (P/W) on Pins 11 and 12, through the LH B-pillar safing sensor and out to the driver side air bag. Current flows through the driver side air bag and into Pin 10 (Circuit 615, GY/W). Current then flows from Pin 10 through the diode inside the diagnostic monitor and out to the primary crash sensors through Pins 17, 18 and 19. The current flows through each primary crash sensor resistor and ends at the case ground of each sensor. Pin 11 is the midpoint of the resistor network and voltage at Pin 11 will change with vehicle charging system voltage. The expected voltage at Pin 11 is shown in the table below. The diagnostic monitor measures the vehicle charging system voltage at Pin 13 (battery input). By measuring the voltage at Pin 13, the diagnostic monitor can accurately predict what the voltage at Pin 11 should be in a normal functioning system.
If the connection between Circuits 614 (GY/O) and 623 (P/W) inside the safing sensor is broken, then the resistor on Pin 12 is no longer in the diagnostic circuit. Both resistors are needed to pull up the diagnostic voltage to the correct value. In this situation, the resistor on Pin 11 is the only resistor inside the diagnostic monitor pulling up the voltage. Therefore, the voltage on Pin 11 will be half of the normal expected voltage and the voltage on Pin 12 will be about equal to the vehicle charging system voltage. The diagnostic monitor does not measure the voltage on Pin 12, so the monitor bases its decision strictly on the voltage at Pin 11. If the voltage at Pin 11 is lower than it should be, the monitor will flash Diagnostic Trouble Code 24. Another situation that can cause low voltage at Pin 11 is a drop in primary crash sensor resistance (resistance is too low). If this occurs, the voltage at Pin 11 will be pulled down to a lower than normal value because the parallel combination resistance of the primary crash sensors will be less than 393 ohms. In this situation, the voltage at Pins 11 and 12 will be identical, but the monitor does not measure the voltage at Pin 12. Therefore, a primary crash sensor with low resistance may cause low voltage at Pin 11 and the monitor will flash Diagnostic Trouble Code 24 on the air bag indicator.
Here is a wiring schematic of this.
http://i253.photobucket.com/albums/hh43/chuck943/93mustangairbag.gif
SOURCE: How do I change an Ignition on a 1988 Ford Mustang GT Automatic
Not exactly sure when Ford changed the style. But I think it is this one. First of all do you have the key thet fits the lock cylinder you are changing? If so, put the key in and turn it to the run position. If this is the style I'm thinking about there will be a small hole in the column cover under the lock cylinder. A small allen wrench works fine. Push in with allen wrench and at the same time pull out on lock cylinder. (you may have to turn key alittle one way or the other to release pin.) If you don't have the key for this lock cylinder it will be EXTREMELY difficult to remove. Hope this is helpful .
SOURCE: how do I change a 2005 mustang alternator? NOT gt
2005 Ford Mustang 4.0L SFI SOHC 6cyl
Ford Mustang 1999-2005
Alternator - Removal & Installation
3.8L And 4.0L Engines
To install:
4.6L Engines (Non-Supercharged)
To install:
4.6L Engines (Supercharged)
To install:
More details about this model in Autozone.com (free register).
I hope help you with this (remember rated this help). Good luck.
256 views
Usually answered in minutes!
×