Question about 1999 Saturn SL

2 Answers

How do you replace water pump in 1999 saturn sl1?

Can i replace the water pump w/o pulling out the motor?

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

View the video on You Tube by Richpin06a. It was very helpful. I don't do many repairs on cars, but with the help of this video, I replaced the waterpump on my Saturn last weekend. It was easy, and I didn't have to remove the engine.

Posted on Dec 31, 2008

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 4 Answers

Yep. It's driven by a belt on the exterior of the engine. Remove the belt and then remove the pump.

Posted on Dec 11, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you get to the water pump to remove and replace it? In a 96 Ford F150 6 cylinder.


pull every thing off in front of motor then pull fan and water pump put new waterpump on

Jan 22, 2010 | 1996 Ford F150 Regular Cab

1 Answer

Windscren washer not working on my peugot207cc


Check the fuse for windscreen washer.
If you can hear the washer motor running but no water comes out then check the washer motor under the side wing cover.
Pull the rubber pipe from motor and then let the washer run to check wheather water will be pumped or not.
If yes the problem is on the side of rubber-pipe to spray-jets on bonet (may be spray jets need some cleaning).
If not then then the problem is in washer pump. The dirt that reside during the time inside washer pump (the plastic pump attached to the washer motor) causing the problem.
Pull out the whole pump motor from tank and disassemble the pump to clean the free moveable conical metal rod and rubber washers (takes about 1.5 hours for cleaning). If you don't want to do it then convenient is to buy another washer (set of motor+pump).

Jan 16, 2010 | 2006 Peugeot 405

1 Answer

2001 Water Pump Replacement


if you are replacing the water pump on a pt cruiser the motor WILL have to come out. you dont have the room to pull the water pump out of the block.. the water pump gets stuck on the c/rail

Aug 31, 2009 | 2001 Chrysler PT Cruiser

1 Answer

Does the motor need to be taken out to replace the water pump?


if you are referring to the engine, no need to remove it but you may have to remove the belts and a cover... depending on the engine

Jun 03, 2009 | 1991 Toyota Celica

1 Answer

Having trouble with my 1974-78 outboard marine engine


Just an idea but your water pump is only rubber and setting for the winter it didnt stick to the sides of where it pumps did it.. sometimes these pumps are tempermental.. you might check your water pump again making sure its pumping right.. is it peeing out the sides good like it is suppose to ? also if its getting hot on top it makes me think the pump is not doing its job right maybe just pumping some.. not enough? just a thought .. thanks Jerry

Apr 27, 2009 | 2004 Mercury Mariner

2 Answers

Over heating


replace thermostat 1st if this dont work check the water pump tp make sure it is working properly. if this info is helpul pleae rate

Apr 19, 2009 | 1998 Ford Taurus

2 Answers

The water pump


ok this is fun lol.jack the car up and put it on a jack stand,then you will have to pull the drivers side tire off.now you need to put a jack under the motor and unbolt the driver side motor mount. lower the motor down it will only go so far.now for the fun part.you got pull the crank pully off there is one bolt in the center of the pully.once you get that off pull the timing cover off top and bottom. there will be 2 belts one is the timing and one is for the water and oil pump. the water pump it the one closest to the back of the motor. it would be best if you replace the timing belt since your already in there.make sure you get ALL the old gasket off the block.you dont want to have to do it twice.oh yeah loosen the tensioner pully to pull off the timing belt it right above the crank one bolt in the center also.if you didnt move anything you should be able to put the new timing belt back on with now problems if you did move something then you got to put it back in time to do that make sure the #1 cylinder is top dead center of the compression strok then turn the cam gear till where its says up on the spoke is pointing up.after that put everything back together and you should be good to go. hope this helps if you have anymore questions just let me know.have fun lol

Jan 15, 2009 | 1991 Honda Accord

1 Answer

REPLACE WATER PUMP THE EASIEST WAY


well get ready cuz ur not gonna like it in order to change the water pump you must remove the top left motor mount then remove all the belts and plastic covers you can get to then pull the harmonic balancer and acc belt tensioner then then remove the rest of the plastic covers take off the timing belt and tensioner pulley assembly then u can remove the water pump install is reverse of tear down but make sure you get the block clean and replace the timing belt too otherwise that water pump wont matter cuz you'll meed a new enginge when that belt breaks

Jan 12, 2009 | 1993 Mitsubishi Eclipse

2 Answers

Water pump replacement


the water pump should be located front right of motor the only thing that may take some time is if the belt needs to be replaced some models require you remove part of the engine mount. Job should take a pump / belt if damaged / antifreeze.

Dec 18, 2008 | 1992 Pontiac Grand Am

Not finding what you are looking for?
1999 Saturn SL Logo

Related Topics:

2,876 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

yadayada
yadayada

Level 3 Expert

69114 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22026 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6817 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...