Question about 1999 Volvo S80

1 Answer

Volvo s80 not cranking

Fan belt broke car turning over but not cranking with the replacement of new belt

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 128 Answers

Check and make sure the timing belt has not slipped. It's possible that the broken drive belt got under the timing belt and made it skip. If this happened, you are in for an expensive repair!

Posted on Dec 09, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are the probable causes for DTC P0335?


Damaged CKP sensor connector Damaged reluctor ring (missing teeth or not turning due to sheared-off keyway) Sensor output open Sensor output shorted to ground Sensor output shorted to voltage Failed crank sensor Broken timing belt Failed PCM are probable causes

Sep 28, 2015 | 2000 Volvo S80

1 Answer

Does a 2000 volvo s80 have a timing chain or timing belt?


It has a belt. If cracked, replace it immediately! Go to Matthews Volvo Site and look for: 99' S80 T6 Cam Seal Replacement/ Oil Leak Repair,Timing,PCV

Jul 03, 2014 | 2000 Volvo S80

1 Answer

Volvo s80 t6 after putting my serpintine belt back on when i started the car a good size of the belt ripped of and wrapped around my harmonic balncer to the timming belt and shut my car right down


Did the piece of serpentine belt actually make contact with the timing belt ? The timing belt should have been behind the timing cover.
And does the engine crank normally ? Normal compression ?

Jan 24, 2014 | 1999 Volvo S80

1 Answer

What happens if a 02 Volvo s80 v6 turbo breaks timing belt??


You have no valve clearance, it definetly hit a exhaust valve , you will need a valve job and find the reason your belt broke to begin with. It is impossible that a valve did not get hit

Mar 12, 2012 | 2002 Volvo S80

2 Answers

1999 volvo s8 timing belt replaement


What about it??
I wouldn't try it if you don't know how, (specially if this is what is known as an interference engine). Valve timing is *very* delicate and stray pistons love to chew them up!

JOAT

Oct 16, 2009 | 1999 Volvo S80

2 Answers

99 Volvo S80 water pump replacement


if this helps.. I had the 1998 model S70. the water pump was driven by the timing belt. you had to take the timing belt off just to replace the water pump. it was just a simple bolt on replacement. the only difficult issue is resetting the hydraulic tensioner on the timing belt. the hydraulic tensioner has to be completely taken off and compressed VERY SLOWLY in a vise. then insert a very hard drill bit or (special volvo tool) into a keeper hole, reinstall hydraulic tensioner onto car and reinstall timing belt.very quickly remove drill bit from keeper hole in tensioner and the tensioner snaps back out to put tension on belt. and you are done.

Jun 15, 2009 | 1999 Volvo S80

1 Answer

1999 volvo s80 t6


just put a compression gauge on each cylinder that will let you know if engine has a bent valve, gauges are relatively cheap. if the belt didn't have anything to do with your timing belt i doubt you have a bent valve, any check engine light? do you have spark? fuel pump turning on when key is turned to on position?

Dec 09, 2008 | 1999 Volvo S80

1 Answer

Volvo s80


If its just a regular drive belt its impossible for this belt to "kick back" and bend a vale. However if this was a timing belt its quite possible to bend valves if it breaks. You problem could be a crank sensor that may have gotten damaged when this belt broke. If the crank sensor is damaged it won't send a reference signal to to computer therefore the vehicle would not have a spark to start. Godd Luck

Dec 09, 2008 | 1999 Volvo S80

1 Answer

Six cylinder volvo s80 straight engine


if it ran ok before the work its not going to be good,start over check all marks the see if you bent any valve by doing a compression test,does it fife? does it have ful pressure

Jul 20, 2008 | 1999 Volvo S80

Not finding what you are looking for?
1999 Volvo S80 Logo

Related Topics:

183 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volvo Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Mark Jones

Level 2 Expert

76 Answers

Are you a Volvo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...