Question about 2004 Ford Ranger

1 Answer

Changing broken antenna on 2004 ford ranger

What exactly do i have to do to change a broken antenna on my ford ranger 2004, is it something i can do or need to take in to a dealer for repair?

Posted by on

  • Anonymous Mar 26, 2014

    How to remove a broken antenna on 2000 ford explorer

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 194 Answers

Ok some of there are screw in antennas and some you need to replace intire wire and all if this is screw off un bolt and install new if not remove your cd player find antenna wire tape a long wire of any kind strong of course go out side and pull wire out then take new antenna wire tape to wire and reverse the pulling to repalce wire to proper location

Posted on Dec 09, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ford ranger 2004 there is no elect.going to pump. I changed the inertia switch --pump still not running.what should I do next ?


Did you check the relay? Power goes from ignition switch to relay to pump. Where B+ stops is your problem.
Run a pair of jumper wire from battery to pump just to see if pump works. If it buzzes and runs its ok.
Then you definately know its something in the control circuit.

May 09, 2010 | 2004 Ford Ranger

1 Answer

2004 Ford Ranger Automatic - While highway driving if I give my truck too much gas when trying to pass it slips into natural. If I let up on the petal, it will go back into gear.


This is typical of the transmissioin or motor mounts being busted or loose & as the drivetrain shifts position from the load change, so does the shift position causing the change from one to the other. good luck.

Jan 31, 2010 | 2004 Ford Ranger

1 Answer

How do I use the 4 wheel drive on my Ford Ranger XLT 2.5 TDi 2004


4L only to be used in extreme condtions
N
4H for off road/snow/ice
2H - normal driving

when switching to 4H vehicle must be stationary, as when changing from 4H to 4L
but it is possible to change from 4H back to 2H while in motion.
when 4wd is engaged a lamp will illuminate on dials telling that the hubs are free wheeling, when changing back to 2H you must press corresponding switch to dis-engage this function

Jan 08, 2010 | 2004 Ford Ranger

1 Answer

2004 ford ranger 4.0 litre. motor is missing and burning gas


You should be showing the check engine light. Rent a scanner, read out any code(s) and pursue to repair(s).

Sep 09, 2009 | 2004 Ford Ranger

1 Answer

!989 Ford Ranger running problem


try checking the voltage regulator
im not sure where itis exactly
but try getting that checked out

May 03, 2009 | 1989 Ford Ranger

1 Answer

Change front hubs


There is a plastic barrel shaped retainer, twist it to the right or left to unlock it, pull it back and the bulb is then removable, it may be sticky but pull straight back it will come out, don't touch the new bulb with your fingers or it will burn out in short order.

Dec 02, 2008 | 2004 Ford Ranger

Not finding what you are looking for?
2004 Ford Ranger Logo

Related Topics:

288 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...