Question about 2007 Toyota Tacoma

1 Answer

Front axle - front drive shaft Toyota tacoma 1998 4x4

Shifting into 4x4 hi from 2x4 hi I can feel shift lever engage the front differential.....crawling underneath truck I can confirm front driveshaft is engaged.

However, no 4x4 the front axle is not driving.

How do I troubleshoot front drive shaft-front axle connection ?

Posted by on

  • 4 more comments 
  • Anonymous Mar 12, 2014

    Indicator says it in

  • Anonymous Mar 14, 2014

    how to change front axle seal on a 1995 chev 4x4

  • Anonymous Mar 16, 2014

    Movement on driveshaft

  • Anonymous Mar 16, 2014

    tranfer case motor doesn,t shift

  • Anonymous Mar 21, 2014

    4x4 not engaging

  • Anonymous Mar 21, 2014

    4x4 not engaging

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

More than like have a broken axle shaft, un hook the rear drive shaft and put it in 4wd if it wont move then you know you got a broken axle shaft or spider gears broke in the pumpkin

Posted on Dec 09, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is there an electric or vacuum switch on a 2001 chevy blazer


There are 2 models here the push button will flash if the system is not engaging or disengaging properly . If front drive shaft is turning. That is with car raised and supported . if front drive axles do not turn then the axle actuator is not engaging axle shaft passenger side. Remove actuator and manually engage shifting collar with a screwdriver still does not turn then inner axle is twisted.

Mar 21, 2014 | 2001 Jeep Grand Cherokee

2 Answers

Got. A 2003 f150 4x4 got problems with 4 wheel drive locking in and stay in drive shaft turning front wheels not


Operationally vacuum shifts the front axle between 2WD and 4WD mode. The GEM ( Generic Electronics Module ) applies ground to the solenoid needed for the mode selected on the switch ( for ESOF ) or when the transfer case shift lever is moved ( MSOF ).The contact plates in the transfer case signal the GEM that the transfer case is engaged, and the Vacuum solenoids need to be activated ( either 2WD to 4WD or 4WD to 2WD ).

Lift and support the front of the truck so the front wheels are off the ground ( take safety precautions, chock wheels, jack stands, etc )
Key on, engage 4x4 and try to turn the front drive shaft.
- If it turns it is a problem with the transfer case.
- If it doesn't it is a front axle engagement problem ( this is what you seem to have, the transfer case is engaged and will drive the front shaft mine was a key on engine off test ).

- If the front drive shaft does not turn :
•With the truck running ( with front wheel back on the ground ), switch from 2WD to 4WD and back again, the vacuum shift motor should move the lever on the front axle.
sscullys_185.jpg
-- If the vacuum shift motor does not move:
1.Check for vacuum on the lines while shifting between modes. Pink vacuum line is 2WD mode, Light Blue vacuum line is 4WD.
2.Check the fuses for the 4WD system and the solenoids.
3.Check the vacuum lines from the vacuum shift motor to the solenoids on the firewall.
sscullys_187.jpg
4.Check the vacuum lines from the solenoids to the vacuum reservoir box behind the battery.
5.Check the vacuum reservoir box for cracks.
6.Typical solution is the vacuum lines ( to the solenoids or to the vacuum shift motor ) are cracked or the vacuum shift motor has a cracked diaphragm and has water in it.
7.Could be the shift plate contacts in the transfer case are corroded / not making good contact, and not activating the solenoids.
sscullys_186.jpg

Usually the case is cracked vacuum lines from the solenoids, the next common is a cracked vacuum reservoir box, and 1 time I have seen the mount for the vacuum disconnect motor broken ( motor floating free so it could not push against the axle )
sscullys_188.jpg

Aug 28, 2011 | 2003 Ford F150 Regular Cab

1 Answer

I can not get power to the motor to engage my front axle on my 4x4.


Power as in 12 V DC ? if yes, you are not in the correct area, the front axle is locked in and out of 4x4 mode with vacuum.

Operationally vacuum shifts the front axle between 2WD and 4WD mode. The GEM ( Generic Electronics Module ) applies ground to the solenoid needed for the mode selected on the switch ( for ESOF ) or when the transfer case shift lever is moved ( MSOF ).The contact plates in the transfer case signal the GEM that the transfer case is engaged, and the Vacuum solenoids need to be activated ( either 2WD to 4WD or 4WD to 2WD ).


Lift and support the front of the truck so the front wheels are off the ground ( take safety precautions, chock wheels, jack stands, etc )
Key on, engage 4x4 and try to turn the front drive shaft.
- If it turns it is a problem with the transfer case.
- If it doesn't it is a front axle engagement problem.

- If the front drive shaft does not turn :
•With the truck running ( with front wheel back on the ground ), switch from 2WD to 4WD and back again, the vacuum shift motor should move the lever on the front axle.
sscullys_200.jpg
Item #10 in this diagram
sscullys_10.gif
-- If the vacuum shift motor does not move:
1.Check for vacuum on the lines while shifting between modes. Pink vacuum line is 2WD mode, Light Blue vacuum line is 4WD.
2.Check the fuses for the 4WD system and the solenoids.
3.Check the vacuum lines from the vacuum shift motor to the solenoids on the firewall.
4.Check the vacuum lines from the solenoids to the vacuum reservoir box behind the battery.
5.Check the vacuum reservoir box for cracks.
6.Typical solution is the vacuum lines ( to the solenoids or to the vacuum shift motor ) are cracked or the vacuum shift motor has a cracked diaphragm and has water in it.
7.Could be the shift plate contacts in the transfer case are corroded / not making good contact, and not activating the solenoids.
sscullys_199.jpg

- If the front drive shaft turns:
For ESOF system
-- Check the fuses for the transfer case, engine compartment fuse panel, 17 & Cab fuse panel fuses 13 and 23 ( verify with owners manual, 97-97 & 99-03 MY can be slightly different on some items ).
-- Try hitting the transfer case with a dead blow hammer ( do not use a metal hammer, it can damage the transfer case ) to see if the transfer case shift motor is hung up .
-- Check the transfer case connector, to make sure the connector pins are clean and making good contact.
For MSOF systems
-- Check that the shift linkage on the transfer case is moving when the lever is moved from 2W to 4H and 4L.

Jul 30, 2011 | 2000 Ford F150 Flareside SuperCab

1 Answer

I have a 2002 ford f150 xlt fx4 4.6l engine. 2 door reg cab. i have a 4 wheel drive shift lever. the 4 wheel will only engage on rare occasion and only after pulling into 4 low then to 2 high then back...


For the 2002 MY ( this is in the 2006 Section, just want to call it out to others that might find the solution, this does not apply to the 2006 MY )

Operationally vacuum shifts the front axle between 2WD and 4WD mode. The GEM ( Generic Electronics Module ) applies ground to the solenoid needed for the mode selected on the switch ( for ESOF ) or when the transfer case shift lever is moved ( MSOF ).The contact plates in the transfer case signal the GEM that the transfer case is engaged, and the Vacuum solenoids need to be activated ( either 2WD to 4WD or 4WD to 2WD ).


Lift and support the front of the truck so the front wheels are off the ground ( take safety precautions, chock wheels, jack stands, etc )
Key on, engage 4x4 and try to turn the front drive shaft.
- If it turns it is a problem with the transfer case.
- If it doesn't it is a front axle engagement problem.

- If the front drive shaft does not turn :
•With the truck running ( with front wheel back on the ground ), switch from 2WD to 4WD and back again, the vacuum shift motor should move the lever on the front axle.
{ picture of shift motor }
-- If the vacuum shift motor does not move:
1.Check for vacuum on the lines while shifting between modes. Pink vacuum line is 2WD mode, Light Blue vacuum line is 4WD.
2.Check the fuses for the 4WD system and the solenoids.
3.Check the vacuum lines from the vacuum shift motor to the solenoids on the firewall.
4.Check the vacuum lines from the solenoids to the vacuum reservoir box behind the battery.
5.Check the vacuum reservoir box for cracks.
6.Typical solution is the vacuum lines ( to the solenoids or to the vacuum shift motor ) are cracked or the vacuum shift motor has a cracked diaphragm and has water in it.
7.Could be the shift plate contacts in the transfer case are corroded / not making good contact, and not activating the solenoids.
sscullys_148.jpg

- If the front drive shaft turns:
For MSOF systems
-- Check that the shift linkage on the transfer case is moving when the lever is moved from 2W to 4H and 4L.

I am going to take a SWAG that it is 1 of 2 places, both cases the front drive shaft is locking into place.

1. The front vacuum shift motor is not moving ( vacuum or vacuum line issue ).
2. The contact plates for the shift motor are not making contact and are not signalling the GEM that the transfer case state has been changed.

I'd start with the front axle off the ground test, and see which way to go, before you start repalcing items.

Mar 27, 2011 | 2006 Ford F-150

1 Answer

KinlogworksI have A 2003 F-150 Super Crew. I have only used th4 wheel drive a few dozen times. about a mounth ago i switched it into 4 high and nothing happened. problem also in 4 low. any advise?


Operationally vacuum shifts the front axle between 2WD and 4WD mode. The GEM ( Generic Electronics Module ) applies ground to the solenoid needed for the mode selected on the switch ( for ESOF ) or when the transfer case shift lever is moved ( MSOF ). The contact plates in the transfer case signal the GEM that the transfer case is engaged, and the Vacuum solenoids need to be activated ( either 2WD to 4WD or 4WD to 2WD ).

Lift and support the front of the truck so the front wheels are off the ground ( take safety precautions, chock wheels, jack stands, etc )
Key on, engage 4x4 and try to turn the front drive shaft.
- If it turns it is a problem with the transfer case.
- If it doesn't it is a front axle engagement problem.

- If the front drive shaft does not turn :
•With the truck running ( with front wheel back on the ground ), switch from 2WD to 4WD and back again, the vacuum shift motor should move the lever on the front axle.
{ picture of shift motor }
-- If the vacuum shift motor does not move:
•Check for vacuum on the lines while shifting between modes. Pink vacuum line is 2WD mode, Light Blue vacuum line is 4WD.
•Check the fuses for the 4WD system and the solenoids.
•Check the vacuum lines from the vacuum shift motor to the solenoids on the firewall.
•Check the vacuum lines from the solenoids to the vacuum reservoir box behind the battery.
•Check the vacuum reservoir box for cracks.
•Typical solution is the vacuum lines ( to the solenoids or to the vacuum shift motor ) are cracked or the vacuum shift motor has a cracked diaphragm and has water in it.
•Could be the shift plate contacts in the transfer case are corroded / not making good contact, and not activating the solenoids.
{ Picture of Vacuum diagram )

- If the front drive shaft turns:
•For ESOF system
-- Check the fuses for the transfer case, engine compartment fuse panel, 17 & Cab fuse panel fuses 13 and 23 ( verify with owners manual, 97-97 & 99-03 MY can be slightly different on some items ).
-- Try hitting the transfer case with a dead blow hammer ( do not use a metal hammer, it can damage the transfer case ) to see if the transfer case shift motor is hung up .
-- Check the transfer case connector, to make sure the connector pins are clean and making good contact.
•For MSOF systems
-- Check that the shift linkage on the transfer case is moving when the lever is moved from 2W to 4H and 4L.

Jan 18, 2011 | 2003 Ford F150 Regular Cab

1 Answer

2003 F-150 regular cab automatic transmission and the 4WD will not engage.


Operationally vacuum shifts the front axle between 2WD and 4WD mode. The GEM ( Generic Electronics Module ) applies ground to the solenoid needed for the mode selected on the switch ( for ESOF ) or when the transfer case shift lever is moved ( MSOF ).The contact plates in the transfer case signal the GEM that the transfer case is engaged, and the Vacuum solenoids need to be activated ( either 2WD to 4WD or 4WD to 2WD ).


Lift and support the front of the truck so the front wheels are off the ground ( take safety precautions, chock wheels, jack stands, etc )
Key on, engage 4x4 and try to turn the front drive shaft.
- If it turns it is a problem with the transfer case.
- If it doesn't it is a front axle engagement problem.

- If the front drive shaft does not turn :
•With the truck running ( with front wheel back on the ground ), switch from 2WD to 4WD and back again, the vacuum shift motor should move the lever on the front axle.
{ picture of shift motor }
-- If the vacuum shift motor does not move:
•Check for vacuum on the lines while shifting between modes. Pink vacuum line is 2WD mode, Light Blue vacuum line is 4WD.
•Check the fuses for the 4WD system and the solenoids.
•Check the vacuum lines from the vacuum shift motor to the solenoids on the firewall.
•Check the vacuum lines from the solenoids to the vacuum reservoir box behind the battery.
•Check the vacuum reservoir box for cracks.
•Typical solution is the vacuum lines ( to the solenoids or to the vacuum shift motor ) are cracked or the vacuum shift motor has a cracked diaphragm and has water in it.
•Could be the shift plate contacts in the transfer case are corroded / not making good contact, and not activating the solenoids.
sscullys_111.jpg

- If the front drive shaft turns:
•For ESOF system
-- Check the fuses for the transfer case, engine compartment fuse panel, 17 & Cab fuse panel fuses 13 and 23 ( verify with owners manual, 97-97 & 99-03 MY can be slightly different on some items ).
-- Try hitting the transfer case with a dead blow hammer ( do not use a metal hammer, it can damage the transfer case ) to see if the transfer case shift motor is hung up .
-- Check the transfer case connector, to make sure the connector pins are clean and making good contact.
•For MSOF systems
-- Check that the shift linkage on the transfer case is moving when the lever is moved from 2W to 4H and 4L.

Jan 10, 2011 | 2003 Ford F150 Regular Cab

1 Answer

When shifting from 3rd to 4th gear during acceleration I experience a shuddering feeling in the rear. What would cause this?


You need to check your drive shaft universal joints. Chock your wheels so the truck can not move or roll. Take It out of gear and grab the drive shaft and try to turn it by hand, looking at the rear joint as you do this, then do the same for the front joint. You are looking for the shaft to move and not the rear or front yoke, if you have a loose feeling that is your U-joint.

Jan 17, 2010 | 2001 Toyota Tacoma

2 Answers

I have a 2000 4wd tacoma with manual locking hubs and the 4wd does not seem to be engaging after locking the hubs and shifting the lever into 4 hi or 4 low


Sounds like one of your hubs is sticking and not engaging. You can check them by engaging the hubs and the transfer case and jacking up each front wheel independently if it doesn't spin your good, if it does you found your problem. As far as fixing a hub goes, it may be just dry and need some grease, or there are some very good aftermarket hubs available from Warn.
Hope this helps

Dec 08, 2009 | 2001 Toyota Tacoma

1 Answer

Toyota Tacoma 1995. Manual transmission will not shift. The shifting lever will not engage with brake pedal pushed. Cannot get the vehicle in neutral, reverse, etc. Also brakelights do not light up while...


the transmission might be rusted on the inside. this happened with my saturn SC2. i just bought a new transmission at a junkyard to fix the issue. there might not be a way to fix the transmission. sorry

Nov 16, 2009 | Toyota Tacoma Cars & Trucks

1 Answer

I have a 2004 chevy silverado and the 4 wheel


the most likely cause is the front axle shift motor if bad your your front axle shaft will not lock in.if there is no shifting of transfer case there is also a electric motor that engages that in .

Oct 17, 2009 | 2004 Chevrolet Silverado 1500 Crew Cab

Not finding what you are looking for?
Cars & Trucks Logo

1,246 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

63990 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...