Question about 2006 Chrysler 300

1 Answer

Running poorly Actually posted this in wrong area before(2005 300) so I will ask again here. Son's car 300 touring 3.5 v6. hard to start, keeps turning over, then starts normally. Sometimes when driving rpms drop suddenly around 60mph then runs normally. Fuel pump maybe?

Posted by on

  • cutlassguy
    cutlassguy Dec 15, 2008

    ended up being throttle position sensor

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 740 Answers

A sudden drop in "rmp" like that is more likely a spark problem not a fuel problem. I would suggest a crank or cam sensor peoblem. Good Luck

Posted on Dec 09, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

89 ford probe hesitates when leaving a red light, then runs fine otherwise, fuel filter?


Engine Runs Rough, Stalls, Hesitates on Acceleration, Hard ...

repairpal.com > Problems > Ford > Probe
Ford Probe Engine Runs Rough, Stalls, Hesitates on Acceleration, Hard Starting, Poor Performance. This is a verified problem based on 9 reports. Learn more ...

Starting Problems - 1997 Ford Probe - RepairPal

repairpal.com > Questions > Ford > Probe > 1997 Ford Probe
Dec 5, 2010 - Starting Problems on 1997 Ford Probe ... If the engine runs rough,stalls, hesitates on acceleration, is hard to start, or has generally poor ...

A new misfire/hesitation on accel. Problem.. - ProbeTalk.com Forums

forums.probetalk.com > Tech Section > 2nd Gen (93-97) V6 2.5L

Feb 05, 2016 | Ford Cars & Trucks

1 Answer

How to install throwout bearing


FSM show this,
or
alldata.com
its just a front or back, orientation asking that?
or how to lock it to the fork? why not say what part fools you.??
ok
no year, you do make this hard and no other post for me to read and find that key fact.!!!
when you bought the part, they ask you year, so.....??????
1989-2004
i spin the wheel of fortune (again) and land 1989
5speed T/o bearing
here is a ASE master answering for the 6v, never post engine not stated. or all answer will be wrong.


http://www.justanswer.com/car/61cqg-1998-isuzu-amigo-tranny-clutch-cannot-bolt-wheel-drive.html
see special tools?
all this is in alldata.com to read, any time of day.

so many engines.....
2.3 L 4ZD1 I4
2.4 L C24SE I4 (GM, Aus)
2.4 L C24NE I4 (Euro)
2.6 L 4ZE1 I4
3.1 L LG6 V6 (GM)
3.2 L 6VD1/6VD1W V6
2.5 L 4JA1 diesel I4 (Cameo, TH)
2.8 L 4JB1-T turbo diesel I4
3.0 L 4JH1-T turbo diesel I4
3.1 L 4JG2 turbo diesel I4

Aug 05, 2014 | Isuzu Amigo Cars & Trucks

1 Answer

1990 isuzu trooper 2 v6 auto poor fuel economy,poor power, oor acceleration,runs like top no oil consumption, whaaaaats wrong please help ?


Check for the catalytic converter being plugged up. The powertrain is actually from GM, and it uses TBI. A plugged catalytic converter will cause all of your symptoms, and yet not trigger a MIL warning light.

Mar 13, 2014 | Cars & Trucks

1 Answer

Overheating at highway speed


old post got air pockets in it, burp it like we do all cars.
ask
see list of 17 signs here, (evidence)
http://www.fixkick.com/overheating.html

and all cures.
just for G16 engines
both 8v and 16valve versions.

i bet its cold out.right? February.
Cel lamp out running, if not, spark timingen may be way wrong.
when the read tubes clog then spark is wrong, the rad can overheats due to 2 failures at once. ? even 3.
or cap is no good, or thermostat bad.
you have tons of cold air there moving so the rad would have to be super clogged to fail
thermostats are weak technogly, see netfilx video of tour o that.
and he show why, they go bad 3 to 5 years old.
shorted lived part. so we always assume that it bad.
like car batteries, same deal ,weak tech.

or not burped right
proof?
easy
  1. pump in, all in.
  2. fill it with 50% AF ,right, to top of neck ,side tank 1/2 full.
  3. run (idle) engine until AF exits filler cap hole, kill engin, put on new cap.
  4. drive around block
  5. let cool below 130F or near.
  6. open cap.
  7. is it still full, sure its not, its got air pockets, all do.
  8. fill again, jump to 4.

g16 are not hard to fill
unless shade tree puts therm stat in, with bleed hole forward ,up hill. or upside down.

Feb 18, 2014 | 1992 Geo Tracker

1 Answer

P1072 bank1 fuel system too heavy


no engine option stated. displacement and cyl. count I6 , V6, I4?

are you asking all ways 1072 can happen?
all this is in the FSM. read it.
but here is the bar stool answer.
warring do not use non jeep P1 codes P1 is Jeep only !!!!!
do not let autozoned, tell you what the code means, they are clerks.
and not trained. (if they did it, you didnt say what tool pulled the code)
i can tell you transposed the 1 and 0, there is no 1072.
so its actually the very common and unversal EPA, P0172.
billions of posts on that www.
P0 means federal codes. a standard
so we look that up, , and is the error for fuel time , too rich.
so i can see you looked it up and got that right but posted wrong dtc.
no problem.
i can go further but not with no engine options stated. .......
the I4, I6 and V6 are all different beasts.

but can say (pure physics and EFI knowledge)
that:
1: the O2 is bad, bank 1 sensor one,Front, or if v6 , bank1, sensor one the bank that is #1 cylinder , front is bad
or
2: engine is running way too rich for 50 reasons, (tests find it)
other sensors bad, mech, eng. issues, leaking injectors, endless....ask
3: exhaust leaks near Sensor 1.

there are the top 3.
what tech might do, is replace the 02 , on suspension.
its older than 100k miles so , bingo its listed in the service sched.
he goes to change it and see the bank header cracked, dang.
example 2, near endless story , ask.....
i run the scan tool and look at all sensor data.
see what is right and wrong.
there are some tricks too, to force lean and see if B1S1 wakes up.
ask


Aug 28, 2013 | 1999 Jeep Cherokee

1 Answer

My son stated that his car would not start, I asked if it is making a clicking noise when turning the key and he said yes.


CHECK BATTERY VOLTAGE IT SHOULD BE 12.5 VOLTS.IF NOT HAVE BATTERY CHECKED OR REPLACED.MAKE SURE BATTERY CABLES + BATTERY POST CLEAN FREE FROM CORROSION AND HAVE TIGHT CONNECTION.IF BATTERY IS WEAK.YOU HAD IT REPLACED CHECK TO MAKE SURE ALTERNATOR OUT PUT AT BATTERY IS 13.5 - 14.5 VOLTS WITH ENGINE RUNNING IF NOT. ALTERNATOR FAULTY.IF BATTERY AND ALTERNATOR OKAY.CLICKING NOISE COULD BE STARTER FAULTY OR POOR NEGATIVE GROUND BATTERY CABLE.

Aug 30, 2010 | Acura TL Cars & Trucks

1 Answer

Saturn vue 2002 starts when it wants to


sounds like a bad crank sensor,nothing you did wrong,just a common 3.0 v6 saturn issue,its located on the front of the engine block under the car by the oil filter housing,,,like $115 for the sensor

Feb 16, 2010 | 2002 Saturn VUE

1 Answer

Symptoms of a failing (plugged) fuel filter - GM V6 Olds Cierra


Rought idel, stalls alot, poor excelaration, starts hard, playing with gas peddel to keep running, they are also symptoms of fuel pump getting weak, or going out, should have fuel pressure test.

Feb 14, 2009 | 1994 Oldsmobile Cutlass Ciera

1 Answer

Crystler 300 Touring running poorly


You have a fuel injector problem. you will need to get the car looked at. There may be a recall, because Crystler knows about this, but I cant say that they have put out a recall for sure yet. Just go to Crystlers web site and look up recalls first. My friends Crystler had this exact same problem.

Dec 09, 2008 | 2005 Chrysler 300

1 Answer

DELAYED STARTUP -- 2000 JEEP GRAND CHEROKEE LAREDO


Our Jeep(s) seem to have problems with the battery clamps much more than I have ever had with other vehicles and often, if the battery was good, cleaning the darned clamps and posts would return it to reliable starting again.
Weak batteries and crummy clamps often only show up during starting because of the vast difference between the current needed to run anything else on a car (the total running current is normally under 20 amps) and the huge surge the starter needs which can approach 200 amps. This high current exposes a weak battery or poor terminal contact real quick. 

Nov 06, 2008 | 2000 Jeep Grand Cherokee

Not finding what you are looking for?
2006 Chrysler 300 Logo

202 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

64034 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

chargerhp
chargerhp

Level 3 Expert

813 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...