Question about 2005 Chrysler Pacifica

1 Answer

Left turn single come on flash sevral time then dim down to were

You cant see it its the only one the rest work find

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 393 Answers

Check the turn sig. flasher also/ try swapping w/the hazard lgts. flasher

Posted on Dec 09, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My right front turn signal on my 2001 ford ranger doesnt work and my inside right turn signal light on dash doesnt work and flashes really fast. Buld on right side was replaced and works when lights


was the correct bulb used? this sounds like a single function bulb was used NOT the bulb that will light with the headlights and ALso produce turn singles

Dec 06, 2014 | 2001 Ford Ranger Regular Cab

1 Answer

Turn singles and flasher don't work on my geo tracker


(work?, dead, flash too fast, stuck on? or are dim?)
fuse blown above left knee.
the schematic is here.
http://www.fixkick.com/ECU/89/1990-scan-ECU/89_elect3a.jpg

the lost panel cover?
http://www.fixkick.com/ECU/89/Fuse-with-diag.jpg

fuse, then wiggle the hanzard switch 5 times.? cycle it
they get dirty, in 24yrs. then the blinker relay model
and last the combo switch bad.

watch out for shorted blinker lamps. (over twisted, they short)
and causes the module to just shut down.
test eash lamp by hand, to be sure its really good.

Feb 19, 2014 | 1990 Geo Tracker

2 Answers

Left turn signal flashes fast but all four will flash. left front is dim.


You need to replace the left front light. The quick flashing is like your check engine light for your blinkers. Once you replace it everything will go back to normal

Nov 28, 2012 | 2004 Honda Accord

1 Answer

I have a 2008 f250. one headlight (driverside) low beam is not working. I have checked both fuses 10amp and they are good. The flash to pass works and both lights on bright, right and left come on. the...


I am sure that a 12 Volt bulb means it needs 12 Volts. Since you changed the bulb to the other side, why not check the voltage in the working side and see what it reads?

Sometimes the turnstalk can interfere with the lighting. Try pushing the Hazard switch several times and see if the headlights straighten out. I read that too much goes through the turnstalk and that using the Hazards can derail a contact inside the stalk.

If this does not help, you may need a headlight relay in the powerbox. One contact may be dirty or burned down for the wire it feeds. Unless you have a single wire feeding both low beams to the headlights, I would bet the left and right side come out directly through the relay.

Oct 20, 2010 | Ford F-250 Cars & Trucks

1 Answer

How do I reset the change oil light on my 2001 silverado?


DID YOU TURN ON IGNITION SWITCH ON AND SLOWLY DEPRESS AND RELEASE THE ACCELERATOR PEDAL 3 TIMES WITHIN 5 SECONDS.IT WILL TAKE LONGER TO RESET DETERMINE HOW LONG YOU LET THE OIL LIGHT STAY ON.WHEN YOU TURN ON SWITCH 5 SECONDS DEPRESS AND AND RELEASE ACCELERATOR 3 TIMES.IF DONT RESET.TURN OFF SWITCH.THEN TURN BACK ON.YOU MAY HAVE TO DO IT SEVERAL TIMES.LET SWITCH REST SOME TRY AGAIN.IT WILL TAKE A WHILE.WHEN EVER CHANGE OIL SOON LIGHT COME ON RESET IT THEN AND CHANGE OIL.DRIVE IT ON A WEEK OR TWO TAKES LONGER TO RESET.

May 30, 2010 | 2000 Chevrolet Silverado

1 Answer

On my 1998 Windstar, when I press on the brake pedal, my left turn signal comes on (dimly). If I am using that signal, it stops flashing and goes dim until I take my foot off the brakes. The right turn...


could be a bad earth unscrew light and check bulb contacts are clean your earth is against the body work when you tighten your light assembly so make sure its clean

Nov 11, 2009 | 1998 Ford Windstar

2 Answers

Turn signals dont flash on 95 firebird formula


There are dual elements bulb and single element bulb.

You need to see is there two contacts inside the socket.

If you accidentally put a single contact bulb into dual contact socket......it will cause this problem.

Check it out.


Jul 14, 2009 | 1996 Pontiac Firebird

1 Answer

No tail lights.


Not posotive with your exact make and model, but their should be a switch directly above where the brake pedal rests normally. It will be a small switch. When you hit the brakes, the switch pops out, and then when it retracts, the pedal itself pushes the button down thus turning the lights off. It shouldn't be but $10 to $15 at the parts store, and installation shouldn't be more than a few screws, and the a small wiring harness clip.

Feb 14, 2009 | 2003 Nissan Altima

Not finding what you are looking for?
2005 Chrysler Pacifica Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

chargerhp
chargerhp

Level 3 Expert

813 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...