Question about 1983 Dodge Charger

1 Answer

I need to replace the motor mounts on my 1983 Dodge Charger 2.2.....where are they located?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 337 Answers

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the vacuum shift motor located?


Gordon, I will take a guess, the Vacuum shift actuator/motor is located on the front axle. Check the attached pictures of actuator and how to replace video,links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Diagnosing 4WD Engagement Problems on Dodge Ram pickups
Front Drive Axle 4wd Vacuum Disconnect Motor 1AFWA00007
Front Axle 4 Wheel Drive Actuator Replacement 4x4 Dodge Ram

May 18, 2016 | 1983 Dodge Ramcharger

1 Answer

Location of ballast resistor dodge ram b250 318 cu I 1983


It's mounted on the firewall near the master cylinder. It is a ceramic material about 3 inches long by 1/2 inch thick. It has a metal band around it used to mount it. There is a wire on each end of the resistor.

Oct 21, 2014 | Cars & Trucks

1 Answer

How to change front motor mount on a 2005 dodge neon


The mount is located under the engine, to replace it you must raise the car up as high as poss and support it with safety stands (a must!) and then unbolt the two engine mounts located about midway along the oil pan and bolted to the engine block, then you must carefully raise the engine off the mounts (do not damage the oil pan) and slide out the old mount and the new one in. You will need allot of tools to get this done, so unless you have all the needed tools don't attempt it.

Feb 23, 2012 | 2005 Dodge Neon

1 Answer

Where are the motor mount located


There are 2 of them, one on each side of the motor. They are located at the base of the motor about center and connect to the front cross member. If you have a sideways mounted 4 cylinder you may have 3 motor mounts, this is common with some Dodge vehicle, They are located 2, upper and lower, on the passenger side of the motor and one actually on the transmission side that connects to the transmission.

May 03, 2011 | GMC Envoy XL Cars & Trucks

1 Answer

I have a 1999 Buick Park Avenue Ultra, the super charger belt needs to be changed along with the seized pulley located behind the motor mount. The mount is located above the crank shaft, attached to the...


I do have a question for you, if you remove the motor mount, can you change the pulley? If this is possible, you will need some jack stands, pieces of 2 by 4's and a hydraulic bottle jack. loosen the motor mount nuts and bolts( don't remove yet), with the bottle jack and a board, lift up the side of the engine(just enough to take pressure off the mount. now remove the mount. lift just a touch more, and set up the jack stands with boards on them(to support, and not damage the engine. also safety first). now lower the engine to the boards replace the pulley, and now go up with the engine, and replace the mount. I've done this on Toyota's,and think this may work for you also. hope this helps

Jan 03, 2011 | Buick Park Avenue Cars & Trucks

1 Answer

2006 dodge charger pcv valve location


5.7L


9491.jpg The PCV valve (3) is mounted into the top/right side of the intake manifold (2).

9493.jpg
1.The PCV valve (1) is sealed to the intake manifold with two O-rings (2).
2.Remove PCV valve by rotating counter-clockwise 90 degrees until locating tabs (3) have been freed. After tabs have cleared, pull valve straight up from intake manifold.3.After valve is removed, check condition of two valve O-rings (2). __________________

Oct 07, 2010 | 2006 Dodge Charger

1 Answer

Clutch adjustment to raise pedal up: Replaced clutch and the pedal is not returning all the way back up. 1972 dodge charger


you need an adjustable clutch rod for under the dash I found one for my ford in the junk yard

Aug 01, 2010 | 1983 Dodge Charger

1 Answer

73 charger with 904 tranny. slips in reverse and drive.


did you replace the seals? One way to check the band and clutch movements is to, valve body off, use a variable air gun on different ports to apply them. There is a hole by each servo to check the band. There are holes along the front side of the case where the VB mounts. Two of those will apply the forward and direct clutch. One way to check units without pulling trans out!

Apr 03, 2009 | 1983 Dodge Charger

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...