Question about 2004 GMC Yukon

1 Answer

Cleaned engine after starting it said stableizing engine disabled

And then it said loss of engine power. Would not go over 35.
engine light came on to.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • GMC Master
  • 846 Answers

I hate to be the one to tell you but nowadays engine cleaner & electronics DO NOT MIX! Out of the 10 miles of wiring in there there may be a bad connection somewhwere.Op out of all of those sensors,one of them where damaged.If you have one,the mass air flow sensor usuall gets it.Take it in to someone you can trust to check it out.Good Luck

Posted on Dec 08, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Power loss and smoking


Toyota Hilux engine power loss Questions & Answers - Fixya

www.fixya.com > ... > Tags > engine power loss > Cars & Trucks > Toyota
Toyota Hilux cars & trucks engine power loss questions and answers. Ask your Toyota engine power loss related question. ... Question about 2006 Hilux 3.0.

Sep 27, 2015 | 2006 Toyota Hilux 3.0

1 Answer

Cause driving along and car shuts off give engine power loss and starting disabled in info center can happen while driving or just sitting idling


Look at your ignition switch for a recall. Tough to know for sure since you failed to say what kind of car you have.

Feb 24, 2015 | Cars & Trucks

1 Answer

Chevrolet code why did starter disabled display appear with loss of power


Check out this site it might be bale to help you.
http://vatspasslockpasskeysecurityhelp.yolasite.com/

Jul 18, 2014 | 2006 Chevrolet Uplander

1 Answer

Going up hill my car losses power.


Year, make, model and engine size, please. Also is the check engine light on and any other symptoms you may have experienced.

Jun 17, 2012 | 1993 Geo Metro

1 Answer

2009 yukon acceleration problems


could be the particulated filter

Jan 29, 2012 | 2009 GMC Yukon

1 Answer

1260 code wont start


P1260 - This, basically is indicating that a theft has occurred, and the engine has been disabled.If the engine stalled, during travel, and the code was pulled after the stall, this will indicate the following:

1.A loss of power, or ground wire to the PCM
2.A Faulty PCM power relay
3.A Faulty EEC power diode
4.A Faulty VERF signal.

Passive Anti-Theft System (PATS) communicates PCM through instrument cluster to enable or disable vehicle's engine. Within one second after engine start, PCM must receive an enable signal from instrument cluster or engine will be disabled. Along with enable signals, instrument cluster and PCM share messages that confirm security codes shared during initial installation. This shared security data makes instrument cluster and PCM a matched pair, so neither will operate in another vehicle. When system is functioning properly and ignition switch is turned to RUN or START position, THEFT indicator light will turn on for 3 seconds, then turn off. Vehicle will be enabled to start and run. If a problem exists in PATS, THEFT indicator light will stay on or flash continuously.


NOTE_ The best action is to clear the code, by using a diagnostic CPU. Plug the CPU into your in car port, under the dash. Follow the instruction on the CPU display to clear the code. if the engine dose not start after the code is cleared, this will indicate that there are some issues with the PCM, or PATS

Nov 11, 2009 | 1999 Ford Taurus

1 Answer

Engine shuts off/ loss of power under load


usually ignition coil will cause you this grief obd 2 scan your engine light to confirm nature of your misfire

Dec 07, 2008 | 1998 Dodge Neon

1 Answer

03 JGC losses power engine light blinks


I would start with a test drive with a fuel pressure gauge on it make sure you have spec. 35 - 40 psi. Clear codes and record all the freeze frame data in obd2 as you will need this in the diag process. 442 and 456 are evap codes I believe, do they return with the 300 misfire codes? Either way you need to reproduce the problem with the gauge on it and get the first code it sets. Could be fuel pump/filter/sending unit assy. In this case you will need to pay attention to the fuel level when this occurs. (same level as before)

Nov 24, 2008 | 2003 Jeep Grand Cherokee

Not finding what you are looking for?
2004 GMC Yukon Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

70365 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...