Question about 2000 Saturn SL

1 Answer

Removal of wheel bearning

How does the front hub/wheel bearning come off of a 2000 saturn

Posted by on

  • laf5 Jan 26, 2009

    I neeed to remove and replace rear wheel hub

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 302 Answers

If you are just pulling the hub, then all you need is a 19mm to take the wheel off, an 18mm for the ball joint nut, 18mm socket and rachet for the tie rod end, I believe a 21mm socket for the strut bolts, then a 14mm and a 18mm for the brake caliper and bracket.

If you plan to press it out yourself you'll need a set of C-clip pliers and a press.

You'll need a breaker bar and 30mm socket for the drive shaft

Posted on Dec 07, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace front wheel bearing?


old post, but you are first to say front. many others fail to say end of car.

is your car 4wd, as 2wd is different rules. so...??????

I toss coin land on 4WD.

2000 front wheel bearing

got it.

the 2000 year, is important.

this year is the last year, before non untized hubs.

http://www.fixkick.com/hubs/FW_BEARINGS.html#newer



my posts is for stock cars. only, and USA spec, cars.

other countries, evolve this in different years.



2000 (never 2001+)

fsm quotes



  1. Before servicing the vehicle, refer to the Precautions section.


  2. Remove or disconnect the following:



    • Front wheel


    • Brake caliper and rotor


    • Locking hub or hub drive flange, if equipped,(it is)


    • Hub grease cap, if equipped


    • Wheel speed sensor, if equipped (ABS)


    • Wheel bearing lockwasher


    • Wheel bearing locknut (ring) and inner washer


    • Wheel hub and bearing assembly (slide hammer?)


    • Wheel hub oil seal


    • Wheel bearing oil seal


    • Snapring




  3. Press the wheel bearing and race out of the hub.


reverse is same but the lock ring must be set

to 123-180PSI. stop tightening above 123 at first alignment hole in lock ring..

Jun 26, 2014 | 2000 Suzuki Grand Vitara

Tip

How To Replace Front Wheel Hub Bearing 2000-05 Buick Lesabre 1AAuto.com


How To Replace Front Wheel Hub Bearing 2000-05 Buick Lesabre 1AAuto.com

on May 08, 2012 | 1997 Buick LeSabre

1 Answer

Install bearn for 2002 kia sedona yes


GO TO SEARS N ROEBUCK AUTO ALIGNMENT CHECK IS FREE THEY WILL TELL YOU WHAT PARTS TAKES 30 - 45 MIN.

Sep 17, 2012 | 2002 Kia Spectra

1 Answer

How do you remove the Hub and Rotor on a 97' F250 with Auto 4 wheel drive? I can not get the rotor to come off. I know that the hub must come with it. However, I am not sure what I have not removed in...


Section 05-03C: Wheel Hubs and Bearings, Front Wheels, 4-Wheel Drive 1997 F-250/350/Super Duty Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 05/17/2000 Locking Hubs, Manual

e9801b.gif


Item Part Number Description 1 3A329 Halfshaft 2 3C132 Rolling Diaphragm Seal (Axle) 3 3299 Integral Spacer Needle Bearing Seal 4 3123 Bearing, Caged Needle 5 3105 Front Wheel Spindle 6 1190 Wheel Hub Grease Seal 7 4221 Inner Wheel Bearing (with Bearing Cup 4222) 8 1102 Front Disc Brake Hub and Rotor 9 4221 Outer Wheel Bearing (with Bearing Cup 4222) 10 - Pin (Part of 1195) 11 1195 Inner Lock Nut 12 1198 Lockwasher 13 1197 Outer Lock Nut 14 - Steel Thrust Washer
(Part of 3B458) 15 - Plastic Thrust Washer
(Part of 3B458) 16 - Splined Thrust Washer
(Part of 3B458) 17 3B457 Snap Ring 18 1K105 Hub Body 19 - Lock Ring (Part of 1K106) 20 1K104 Cap 21 1K104 Capscrew A - While Rotating Front Disc Brake Hub and Rotor, Tighten Inner Lock Nut to 68 Nm (50 Lb-Ft) to Seat Bearings. Back Nut Off 90 Degrees (1/4 Turn). B - Tighten to 217-278 Nm (160-205 Lb-Ft) C - Tighten to 4-6 Nm
(35-53 Lb-In) Removal
  1. Separate cap assembly from hub body by removing the three Torx® head capscrews.


    de0460a.gif



    de0285a.gif

  1. Remove the lock ring seated in the groove of the front disc brake hub and rotor (1102).


    f4658c.gif

  1. Remove the hub body assembly from the front disc brake hub and rotor. If the body is difficult to remove, install two capscrews and pull the body assembly out of the front disc brake hub and rotor.


    f4659d.gif

Installation
  1. NOTE: Do not pack the hublock body assembly or cap with grease. Excessive grease can cause excessive dialing effort and hub failure.

    Follow removal procedure in reverse order.
  1. Tighten three Torx® head capscrews to 4-6 Nm (35-53 lb-in).

Oct 04, 2010 | 1997 Ford F250 SuperCab

1 Answer

How do I remove the wheel bearing on a 2000 Saturn SL1? I have removed everything except pulling the housing which holds the bearing.


I believe on these cars you have to replace the entire hub, not just the bearing. I had a problem with mine and I went to a junk yard and bought a used wheel with the hub still attached, fixed it right up.

Apr 11, 2010 | 2000 Saturn SL

1 Answer

How to rebuild front hub and wheel bearing assembly


Does the hub unbolt from the knuckle or is it pressed in

Mar 30, 2010 | 2000 Saturn Ls 4dr Sedan

1 Answer

How to remove front wheel hub 1996 saturn


You have to remove the wheel, and take off the brake caliper, and bracket.You then have to unbolt the steering arm balljoint, and the lower control arm balljoint.You will have to unbolt the strut also from the the hub assembly. I used a three jaw puller to push the cv axle out of the middle of the hub, then u will have hub in hand. the center of the hub has to be removed by using a press to push it out, and if you r changing the wheel bearing u will have to press that out too. Clean hub up really well, and u will have to use press to reinstall the new bearing, and the center of the hub. If u do not have access to press, take the hub to dealer service department, and they can do it for u. You will then have to put it all back together is reverse order.

Mar 28, 2009 | 1996 Saturn SL

1 Answer

Can you just replace the bearning in the wheel hub?


no the bearing and hub are an assembly and are replaced as 1 i know they are crazy expensive.good luck

Mar 23, 2009 | 2002 Chevrolet TrailBlazer

1 Answer

How to change the front wheel hub for 2000 LINCOLN LS


hi you will have to remove the wheel,grease cap from the hub remove the brake caliper and move aside (do not seporate rubber line). (discard caliper bolts can not be reused) remove rotor,wheel hub retainer nut (and discard nut can not be reused) in order to remove the hub

install

hub and new nut and tighten new nut to 189-254 ft.lbs
rotor new grease cap seal
brake caliper with 2 new bolts tighten to125-170 ft.lbs
wheel tighten to85-104 ft.lbs
pump the brake pedal befor moving car

Feb 06, 2009 | 2000 Lincoln LS

Not finding what you are looking for?
2000 Saturn SL Logo

Related Topics:

115 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...