Question about 1999 Ford F150 Regular Cab

Open Question

Replacing front rotors on a 1999 ford f-150

I have a 1999 f-150 what size socket do i need to remove the caliper so i can change the rotors

Posted by on

1 Suggested Answer

  • 1 Answer

SOURCE: changing front rotors

15mm I tried several and that one fit best.

Posted on Dec 26, 2008


Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What size Allen wrench for 2001 escape front caliper?


i just changed my front rotors and pads on my 2001 escape, 6 cylinder. everyone was wrong on the wrench sizes, including the idiots at my local ford dealer. to get the brake calipers off I needed a 7mm hex bit. to get the caliper bracket off I needed an 18mm socket, it was a very easy job but check your wrench sizes first, it seems that every year and model uses different sizes.

Mar 11, 2012 | 2001 Ford Escape

2 Answers

What size allen wrench to remove front brake caliper


i just changed my front rotors and pads on my 2001 escape, 6 cylinder. everyone was wrong on the wrench sizes, including the idiots at my local ford dealer. to get the brake calipers off I needed a 7mm hex bit. to get the caliper bracket off I needed an 18mm socket, it was a very easy job but check your wrench sizes first, it seems that every year and model uses different sizes.

Oct 19, 2010 | 2005 Ford Escape

2 Answers

Need to replace front rotor of 1984 Ford Bronco


Remove tire and remove the two bolts to the caliper remove caliper install new rotor, using a clamp and a socket push the system back all the way position. Install brakes and caliper make sure everything is tight and reinstall tire.pump up the brakes start car pump up breaks again until light goes out.

Nov 05, 2009 | 1984 Ford Bronco

1 Answer

1996 Grand Prix caliper bracket 'star' socket size


60 will is the right socket, I'll recomend getting one in 1/2" drive, they can be tight!

Oct 25, 2009 | 1996 Pontiac Grand Prix

2 Answers

Tool to remove front brake caliper to replace rotor Escape 2005


You need a 7mm socket, which are available at auto parts stores.

Jun 20, 2009 | 2005 Ford Escape

1 Answer

Rear rotors need to be changed out


remove the wheel, use a large c-clamp to bottom out the caliper pistons,remove the caliper bolts,remove the caliper, hang it from a coathanger to protect the brakeline, unbolt the rotor and, remove

May 29, 2009 | 2007 Ford F-150 Harley Davidson

1 Answer

I have a 2000 Passat and going to have my friend replace the rotors and breaks. I am preparing to fix it but want to know what sizes are the bolts for the calipers sliding pins. If you know the Bolt s


For a wrench or for the acctual bolt size.
To remove front pads..you need 8mm allen socket to pull the caliper guide pins, then 17 or 18mm..To remove rear pads...you need 13mm socket for lock bolt on guide pins and 15mm open end wrench (thin section to hold guide pin while you remove lock bolts..I ground down a spare wrench). You DO NOT have to remove rear carriers to change rotors..just remove lock screw and angle rotor out. The B5 Passats don't have the electronic parking brake so you don't need VAG Com to change pads.
Installation tips:
Clean and regrease the guide pins with "synthetic caliper grease"
Rear lock bolts come with preapplied thread locker and "are not to be reused"..I just wire brush the threads and use some Loctite Blue on em. I smear just a little antisieze on the inside bore of the rotors and on the lock screw threads to prevent corrosion and make next rotor change ez. Torques:
Front caliper guide pins:18 ft lb
Front carrier bolts: 89 ft lb
Rear guide pin lock bolts:26 ft lb
Wheel lugs: 89 ft lb

May 29, 2009 | 2000 Volkswagen Passat 4Motion

1 Answer

I need to know the procedure for r and r on a front rotor if this is something that can be done at home with limited tools?


1999 Taurus/Sable Section 06-03: Brakes, Front Disc 1999 Taurus/Sable Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/25/1998 Disc Removal
  1. Raise vehicle on hoist.
  1. Remove wheel and tire assembly. Be careful to avoid damage or interference with caliper bleeder screw fitting and front disc brake rotor shield (2K004).
  1. ani_caut.gif CAUTION: Handle front disc brake rotor (1125) and disc brake caliper (2B120) assembly in such a way as to prevent deformation of front disc brake rotor , and nicking, scratching or contamination of brake linings/rotor surfaces.
    NOTE: To prevent damage, do not allow disc brake caliper to hang by the front brake hose (2078) .


    Remove caliper anchor plate bolts and discard. Position disc brake caliper out of the way. Prevent separation of caliper housing from anchor bracket because contamination of guide pin journals can occur.
  1. NOTE: If excessive force must be used during front disc brake rotor removal, the front disc brake rotor should be checked for runout prior to installation.


    If additional force is required to remove front disc brake rotor , apply Rust Penetrant and Inhibitor F2AZ-19A501-A or equivalent meeting Ford specification ESR-M99C56-A on front and rear rotor/hub mating surfaces. First, strike front disc brake rotor between lug bolts (1107) with a plastic hammer. If this does not work, attach 2-3 Jaw Puller 205-D027 (D80L-1013-A) or equivalent and remove front disc brake rotor . Remove front disc brake rotor from wheel hub (1104) assembly by pulling it off the lug bolts.
Installation
  1. If original front disc brake rotor is being installed, make sure rotor braking and mounting surfaces are clean.
  1. ani_caut.gif CAUTION: Failure to clean rust and foreign material from rotor and hub mounting faces when installing new or old front disc brake rotors will result in high rotor runout, which will speed up the development of brake roughness shudder vibration.
    Apply a small amount of Silicone Brake Caliper Grease and Dielectric Compound D7AZ-19A331-A or equivalent meeting Ford specification ESE-M1C171-A to pilot diameter of front disc brake rotor.
  1. Install front disc brake rotor on wheel hub assembly.
  1. Install disc brake caliper and new caliper anchor bracket bolts on front disc brake rotor . Tighten caliper anchor bracket bolts to 88-118 Nm (65-87 lb-ft).
  1. ani_caut.gif CAUTION: Failure to tighten lug nuts (1012) in a star pattern may result in high rotor runout, which will speed up the development of brake roughness, shudder and vibration.
    Install wheel and tire assembly on vehicle. Tighten lug nuts to 115-142 Nm (85-104 lb-ft) using Rotunda Accutorq® Lug Nut Socket 164-R0303 or equivalent on a 1/2 inch air impact wrench, or use a torque wrench.
  1. Lower vehicle.
  1. Pump brake pedal prior to moving vehicle to position brake linings.
  1. Road test vehicle.









May 25, 2009 | 1999 Mercury Sable

3 Answers

Replacing the front brake caliper on a 1999 Ford Escort


Very simple. Have the proper tools for one. Two...lay cardboard down because the brake dust will make some cruddy marks on the pavement. Three...are replacing the WHOL:E caliper or just replacing/resealing the piston?

Very simple to do, just make sure you block the rear wheels or front (depending on which one you are doing).

Unbolt the two carrier bolts, one upper and one lower. These are commonly hex head or "allen" head fastners. Next, have a small container under the hose you will be disconnecting. I hope you have some help to bleed.....you will need to do so. Get the extra brake fluid ahead of time....that's all you need to do really...and once you unblot and disconnect, the brake caliper should be sitting in your lap!

Mar 12, 2009 | 1999 Ford Escort

Not finding what you are looking for?
1999 Ford F150 Regular Cab Logo

Related Topics:

82 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

63801 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...