Question about 1996 Dodge Stratus

1 Answer

What is the torque setting for the bolts on a transmission pan for a 1996 Dodge Stratus?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 16 Answers

14 ft. lbs

Posted on Dec 08, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Automatic change 2001 dodge stratus r/t transmission filter


you have to take out all the bolt on the trans pan ( start at one corner with a oil drain container under that corner because the more bolts you take out the fluid will come out faster (about 1-2 gallons total) ounce you have the pan off the just wiggle as you pull down on the old filter and push the new in (all the way in) replace your pan gasket and put bolts back it. refill the trans through the trans dip stick

Jan 28, 2013 | 2001 Dodge Stratus

1 Answer

Removal of oil pan 2003 dodge stratus


To get the oil pan off of your 2003 Dodge Stratus 2.7L engine, you must remove the following:
> Engine oil dipstick and tube
> Engine oil filter
> Structural collar (metal plate that bolts on the bottom between the oil pan and transmission housing)
> Exhaust cross-under pipe
> Torque converter housing cover
> The lower bolt attaching the A/C compressor to the oil pan
> Oil pan fasteners, Oil pan and gasket
Please note that attempting to remove the exhaust cross-under pipe can be a real challenge if you do not have the equipment to heat the nuts/studs that fasten it to the manifolds.
Non-availability of the required equipment in this case may mean that you will have to remove the exhaust manifold(s) to drill out broken studs.

May 16, 2012 | 2002 Dodge Stratus

1 Answer

How do you get the oil pan off of a 2006 dodge stratus 2.7L


Hope this helps and please don't forget to rate!


  1. Disconnect the negative battery cable.
  2. Remove the engine oil dipstick and tube.
  3. Raise and safely support the vehicle.
  4. Drain the engine oil and remove the oil filter.
  5. Remove the structural collar.
  6. Remove the exhaust cross-under pipe.
  7. Remove the torque converter housing cover.
  8. Remove the lower bolt attaching the A/C compressor to the oil pan.
WARNING!!!!!
Be sure to remove the 2 bolts attaching the timing cover to the oil pan, as damage to the timing cover and/or oil pan may occur.
  1. Remove the oil pan attaching fasteners.
  2. Remove the oil pan and gasket.

May 08, 2011 | 2006 Dodge Stratus

1 Answer

My transmission pan has metal shavings and it won't shift out of low gear. is it a sensor or do i need to rebuild my transmission. 1996 dodge stratus se 2.4 l


metal shavings is a good indicator the trany needs rebuilt,( those metal shavings are from drive gears inside of trany)but the only way to know 100% is to take it in. sorry that happened to you....i know that's not the answer you where looking for.

Sep 28, 2010 | 1996 Dodge Stratus

1 Answer

I need torque specs for the head bolts on a 2004 Dodge Stratus Coupe 2.4L SOHC


For 2004 Dodge Stratus 2.4L SFI SOHC 4cyl the Head Bolt Torque sequence
------------ | 10 6 2 3 7 | | 9 5 1 4 8 | ------------

Step: 1 - Torque to 25 ft/lbs
Steps: 2 - Torque to 50 ft/lbs
Steps: 3 - Torque to 50 ft/lbs
Steps: 4 - Turn 90 degreesRecheck final torque in sequence

Caution:Engine uses torque to yield head bolts (TTY) that permanently stretch during initial installation. New head bolts must be used when cylinder headis replaced or re installed to obtain proper torque specification.

Hope helps (remember comment and rated this).

Aug 02, 2010 | 2004 Dodge Stratus

3 Answers

Filter for transmission located for a 2001 dodge stratus.


jack up the car and put it on stands. remove the drivers side plastic shield next to the transmission. remove the 10mm bolts from the rear and sides of the trans and loosen the ones in front. keep a pan under the trans as you will drain the fluid this way. once you have the fluid out, remove the remaining bolts and drain the last of the fluid. The filter is visible under the trans. Be sure to remove the o-ring in the hole. Replace the filter and make sure it seats in place. Scrape off any silicone gasket material and install the pan gasket and pan. The bolts torque to 165 inch pounds or about 13 ft/lbs. Add in 4 quarts of transmission fluid. Start the car, keep your foot on the break and shift the car into each of the gears to fill up the trans piping with fluid.

Jun 07, 2010 | 2001 Dodge Stratus

1 Answer

Cant find the right bolt torque sequenceor bolt


Cylinder head bolts for 2.4 doch in ft\lbs
Step 1 .....................................................................................25
Step 2......................................................................................50
Step 3.......................................................................................50
Step 4.....................................Tighten an additional 1/4 turn (90-degrees)


the order is shown in this image:http://yfrog.com/2ocylinderheadj

Jan 21, 2010 | 1996 Dodge Stratus

1 Answer

Remove oil pan on 98 dodge stratus? The mount bar is preventing me from reaching the back two bolts. Is there a special tool or do you have to remove the transmission?


Most cars today you have to raise the engine somewhat to remove the oil pan. To do so you'll need to first support the engine (use a lift if you can) and unbolt the engine mounts. Before lifting look at any wires, hoses or such which could be of issue if the engine were raised. If so remove or move as required. Once this is done you may be able to raise the engine (slightly) to access the bolts and remove the pan.
I hope this mauy have helped,
Tom

Oct 15, 2009 | 1996 Dodge Stratus

1 Answer

Transmission toque specs


The spec is 12 ft lbs of torque. Use a an even pattern when you tighten the bolts, this assures the gasket will not be damaged and create another leak.

Jul 27, 2008 | 2003 Dodge Stratus

Not finding what you are looking for?
1996 Dodge Stratus Logo

Related Topics:

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

63577 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...