Question about 1992 Geo Metro

1 Answer

Timing belt marks

I'm trying to install a timing belt. How do I set the cam pulley so I can time it to the crankshaft pully on a 1992 GEO 1 liter eng. I can't find any marks on the camshaft to aline on anything. I found a dot on the crankshaft pully. What do I set it on? Thanks for your help.

Posted by on

  • hmbland4 Dec 09, 2008

    So for, you haven't come near answering my question. I don't know where your going with this. I think you people are going to try a make me pay for this imfo. I want. I want nothing to do with you people. Thanks but no thanks Forget it.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 337 Answers

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No just finished a valve replacement on 92 geo tracker 8v eng. set crank to TDC on #4 cyl and the cam to the proper alignment notch on rear valve cover and installed the new timing belt. However after all...


When timing belts are installed, the normal position of the crankshaft is for #1 cylinder to be at TDC. Here is a picture of the timing belt routing and the timing marks.

chuckster57_44.gif

Jun 04, 2011 | 1992 Geo Tracker

1 Answer

Need timing blet diagram 1992 ford ranger 2.3


Hi, the crankshaft marks are on the belt pulley and timing cover, so you have to mate it up to see them. The cam sprocket mark goes on the bottom, and aligns with another mark on the timing cover. There is a plug you pull out and hole to look thru to align the cam sprocket/shaft.


jturcotte_1801.gif


jturcotte_1802.gif


Rotate the engine so that No. 1 cylinder is at TDC on the compression stroke. Check that the timing marks are aligned on the camshaft and crankshaft pulleys. An access plug is provided in the cam belt cover so that the camshaft timing can be checked without removal of the cover or any other parts. Set the crankshaft to TDC by aligning the timing mark on the crank pulley with the TDC mark on the belt cover. Look through the access hole in the belt cover to make sure that the timing mark on the cam drive sprocket is lined up with the pointer on the inner belt cover.

Jun 01, 2011 | Ford Ranger Cars & Trucks

1 Answer

Gearbox chatter on tick over do they suffer from dualmass problems also is there a quick way to change the cambelt


Dual Mass Flywheel, and will also need new clutch Remove the engine coverUsing a [16 mm], rotate the tensioner arm clockwise (about 14° )and remove the belt from the pulley.
Remove the power steering pump pulley, idler pulley, tensioner pulley and crankshaft pulley.
Remove the upper and lower timing belt covers.

Remove the auto tensioner.
NOTE
Rotate the crankshaft clockwise and align the timing mark to set the No.1 cylinder's piston to TDC (compression stroke).
At this time, the timing marks of the camshaft sprocket and cylinder head cover should coincide with each other.




Unbolt the tensioner to remove the timing belt.
NOTE
If you plan to use the timing belt again, mark the rotation direction on the belt so you reinstall it correctly.

SERVICE MANUAL
Applies to: Santa Fe 2004
GROUP
Engine Mechanical System Timing System



INSTALLATION
Install the idler pulley to water pump boss.
NOTE
Insert and install the idler pulley to the roll pin that is pressed in the water pump boss.


Install the tensioner arm and plain washer to the cylinder block.
Install the tensioner pulley to the tensioner arm.
Install the camshaft sprockets and align the timing marks.

NOTE
When installing the camshaft sprockets, fasten them tightly while holding the hexagonal part of the camshaft.
Before installing the timing belt, if the timing marks of the cam sprocket and the cylinder head cover do not coincide, do not rotate the cam sprocket more than 3 teeth in either direction.
Rotating the sprocket more than 3 teeth may allow the valve and piston to touch each other.
If the cam sprocket is rotated more than 3 teeth unavoidably, rotate the crankshaft counter - clock wise a bit before rotating the cam sprocket.
Install the auto tensioner to the front case.
NOTE
At this time auto tensioner's set pin should be compressed and secured with set pin.




Align the timing marks of each sprocket and install the timing belt in the following order. Crankshaft sprocket--> Idler pulley--> camshaft sprocket (LH side)--> Water pump pulley--> camshaft sprocket (RH side)--> Tensioner pulley.
NOTE
In this step, No. 1 cylinder is in the TDC (Compression stroke).
Be very careful if you use your fingers.



Pull out the set pin of the auto tensioner.



Install the upper and lower timing belt covers.
Install the power steering pump pulley, idler pulley, tensioner pulley and crankshaft pulley.
Using the wrench [16mm], rotate the tensioner arm clockwise (about 14°) and install the belt to the pulley.
Install the engine cover.
How to adjust the tension of the timing belt
Rotate the crankshaft 2 turns clockwise and measure the projected length of the auto tensioner at TDC (# 1 Compression stroke) after 5 minutes.
The projected length should be 6-8 mm.
Verify that the timing marks of each sprocket are in their specified position.
NOTE
If the timing marks are not in their specified position, repeat from 6 above.

Dec 28, 2010 | 2004 Hyundai Santa Fe

1 Answer

We just replaced a torn timing belt and crank position sensor on my 03 lancer. the engine will not fire. how do we set the timing points? I cannot find a repair manual for this year lancer anywhere.


With the belt off and the tensioner pulley pushed back, you will need to set cylinder 1 (far passenger side) to top dead center. There is a mark on the block you can see just behind the crankshaft gear that needs to be aligned to the mark on the crankshaft gear. CAUTION NOT TO TURN THE CAM PULLEY TOO FAR IF ANY PISTONS ARE AT TDC, they will contact the piston on this motor. turn the crankshaft gear forward or backward 1/4 turn off of TDC when you move the cam pully. Once this is done, you will need to set the camshaft pulley to a poorly designed mark on the cylinder head. (it is the corner point of the casting for the cylinder head, it forms a triangle at about the 10:00 position when looking at the cam pulley). Install your belt, it will be tight even with the tensioner pulled back so making sure it doesn't cause either of the gears to move off their marks. Once it on recheck the timing marks upper (cam) and lower (crank), release the tensioner, put your other belt on and you're done. http://www.mivec.co.nz/tech/4G9x_Engine_Manual.pdf

Dec 17, 2010 | 2003 Mitsubishi Lancer

2 Answers

Looking for timing mark's for a 1997 camry with a 2.2 4cyl motor?


Hi,


You find the timing marks on the picture below.

moz-screenshot-2.pngaab8238.jpg



Removal
Remove auxiliary 1. drive belts.
2. Support engine.
Remove:
Engine mounting and bracket.
Timing belt upper cover [1].
3.
4. Turn crankshaft clockwise to TDC on No.1 cylinder. Ensure timing marks aligned [2] & [3].
Remove:
Crankshaft pulley bolt [4].
Crankshaft pulley [5]. Use tool No.09213-60017.
5.
6. Ensure timing marks aligned [2] & [3].
7. Slacken tensioner bolt [6]. Move tensioner away from belt and lightly tighten bolt.
Remove:
Timing belt lower cover [7].
Crankshaft sprocket guide washer [9].
Timing belt.
Tensioner pulley.

Installation
Installation
1. Check tensioner pulley for smooth operation.
2. Check free length of tensioner spring is 46,0 mm [8]. Replace spring if necessary.
3. Fit tensioner and spring. Ensure spring is connected correctly.
4. tighten bolt [6].
5. Ensure timing marks aligned [2] & [3].
6. Fit timing belt. Ensure belt is taut between sprockets.
Install:
Crankshaft sprocket guide washer [9].
Timing belt lower cover [7].
Crankshaft pulley [5].
7.
8. Slacken tensioner bolt 1/2 turn [6].
9. Turn crankshaft two turns clockwise to TDC on No.1 cylinder. Ensure timing marks aligned [2] & [3].
Turn crankshaft slowly 1 7/8 turns clockwise until crankshaft pulley timing mark [3] aligned with 45° BTDC mark [10] on
timing belt lower cover [7].
10.
11. Tighten tensioner bolt [6]. Tightening torque: 42 Nm.
12. Install components in reverse order of removal.
13. Tighten crankshaft pulley bolt [4]. Tightening torque: 108 Nm.
Manufacturer: Toyota

Jun 25, 2010 | 1997 Toyota Camry

1 Answer

Timing marks setting Hyundai Lantra


Installation
Ensure timing marks aligned [6] & [7] . 1. Fit timing belt in anti-clockwise direction, starting at crankshaft sprocket. Ensure belt is taut between sprockets. 2. Slacken tensioner pulley bolt [8] . Push tensioner pulley firmly against timing belt to tension belt. 3. Tighten tensioner pulley bolt [8] . Tightening torque: 43-55 Nm. 4. Except Matrix: Turn crankshaft one turn clockwise. 5. Matrix: Turn crankshaft two turns clockwise. 6. Ensure timing marks aligned [6] . 7. Apply a load of 2 kg to belt at . Belt should deflect 4-6 mm. If not: Adjust position of tensioner pulley. 8. Install components in reverse order of removal. 9. Tighten crankshaft pulley bolt [2] . Tightening torque: 170-180 Nm

7 is timing mark on cam,pin mark to top,hole in spoke below pin mark lines up with mark on head
6 is crank timing mark,pin mark on crank lines up with mark on block
NOTE this mark is just before top


Mar 21, 2010 | Hyundai Motor 1996 Elantra

2 Answers

Timing belt geo metro 95 hatchback


roll the crankshaft pulley around until u get the mark to line up with 0 or TDC. once u get the cover off mark the cam sproket to the head with whiteout and mark the crank gear to the block also. (in case they move on you. loosen tensioner and pry to one side.tighten tensioner bolt and remove the belt. install new belt and get the slack to move toward the tensioner side. (u may have to move the cam slightly to allow all the slack to go toward the tensioner. then move it back to the mark, making sure the crank didnt move. loosen tensioner bolt and let it spring toward the belt and apply pressure with yr hand a little more snug while u tightn bolt. then rotate the crankshaft 2 revolutions by hand and your marks should line back up. if the marks are more than 1/2 tooth off u must re do it!

Feb 20, 2010 | 1995 Geo Metro

4 Answers

1992 Volvo 960 Broken timing belt - need to locate alignment marks for crankshaft and camshaft and associated reference marks for TDC or other position. Car was cranked AFTER belt broke - Crankshaft Is...


IF U BROKE THIS BELT WHILE DRIVING U HAVE BENT THE VALVES IN THE ENGINE, THIS IS WHAT IS CALLED AN INTERFERENCE DESIGN ENGINE, THAT MEANS WHEN THE TIMING BELT BREAKS THE PISTONS HIT THE ENGINES VALVES

Nov 11, 2009 | 1992 Volvo 960

1 Answer

Timing for tropper 6cly and 4 camshafts and 24 valves model 2000


Timing Belt
Removal
1. Disconnect battery ground cable.
2. Remove air cleaner assembly.
3. Remove radiator upper fan shroud from radiator.
4. Move drive belt tensioner to loose side using wrench
then remove drive belt.
850RW001
Legend
(1) Crankshaft Pulley
(2) Cooling Fan Pulley
(3) Tensioner
(4) Generator
(5) Air Conditioner Compressor
(6) Power Steering Oil Pump
(7) Drive Belt
5. Remove cooling fan assembly four nuts, then the
cooling fan assembly.
6. Remove cooling fan drive pulley assembly.
7. Remove idle pulley assembly.
8. Remove serpentine belt tensioner assembly.
9. Remove power steering pump assembly.
10.Remove crankshaft pulley assembly using
5–8840–0133–0 crankshaft holder, hold crankshaft
pulley remove center bolt, then the pulley.
11. Remove right side timing belt cover then left side
timing belt cover.
12. Remove lower timing belt cover
13. Remove pusher.
CAUTION: The pusher prevents air from entering
the oil chamber. Its rod must always be facing
upward.
014RW011
Legend
(1) Up Side
(2) Down Side
(3) Direction For Installation
(4) Locking Pin
14. Remove timing belt.
CAUTION:
1. Do not bend or twist the belt, otherwise its core
could be damaged. The belt should not be bent at
a radius less than 30 mm.
2. Do not allow oil or other chemical substances to
come in contact with the belt. They will shorten
the life.
3. Do not attempt to pry or stretch the belt with a
screw driver or any other tool during installation.
4. Store timing belt in a cool and dark place. Never
expose the belt direct sunlight or heat.
6A–30 ENGINE MECHANICAL
Installation
NOTE: For correct belt installation, the letter on the belt
must be able to be read as viewed from the front of the
vehicle.
014RY00042
Legend
(1) Crankshaft Timing Pulley
(2) RH Bank Camshaft Drive Gear Pulley
(3) Water Pump Pulley
(4) Idle Pulley
(5) LH Bank Camshaft Drive Gear Pulley
(6) Tension Pulley
014RY00043
Legend
(7) Alignment Mark on Oil Pump.
(8) Alignment Mark on Timing Belt
(9) Alignment Mark (notch) on Crankshaft Timing
Pulley.
(10) Alignment Mark (groove) on Crankshaft Timing
Pulley.
014RW006
Legend
(1) Timing Belt
(2) Engine Rotation Direction
(3) Cylinder Head Side
1. Install timing belt.
1. Align the mark (notch) of crankshaft timing pulley
(2) with mark on oil pump (1).
Align the mark (groove) on the crankshaft timing
pulley (3) with alignment mark (white dots line) on
the timing belt (4).
NOTE: When timing marks are aligned, No.2 piston will
be on Top Dead Center.
014RW003
Legend
(1) Alignment Mark on Oil Pump
(2) Groove on Crankshaft Timing Pulley
(3) Alignment Mark on Crankshaft Timing Pulley
(4) Alignment Mark on Timing Belt
ENGINE MECHANICAL 6A–31
2. Align the alignment mark on the RH bank
camshaft drive gear pulley (2) to the alignment
mark of the cylinder head cover RH (3).
3. Align the alignment mark (white line) on the timing
belt (1) with alignment mark on the RH bank
camshaft drive gear pulley (2) (on the left side as
viewed from the front of the vehicle) and put the
timing belt on the camshaft drive gear pulley.
Secure the belt with a double clip or equivalent
clip.
014RW00004
Legend
(1) Alignment Mark on Timing Belt (White line).
(2) Alignment Mark on Camshaft Drive Gear
Pulley.
(3) Alignemnt Mark on Cylinder Head Cover RH.
4. Align the alignment mark on the LH bank
camshaft drive gear pulley (2) to the alignment
mark of the cylinder head cover LH (3).
5. Align the alignment mark (white line) on the timing
belt (1) with the alignment mark on the LH bank
camshaft drive gear pulley (2).
When aligning the timing marks, use a wrench to
turn the camshaft drive gear pulley, then set the
timing mark between timing belt and camshaft
drive gear pulley and put the timing belt on the
camshaft drive gear pulley.
Secure the belt with a double clip or equivalent
clip.
NOTE: It is recommended for easy installation that the
belt be secured with a double clip or equivalent clip after
it is installed the timing belt to each pulley.
014RW00005
Legend
(1) Alignment Mark on Timing Belt (White line).
(2) Alignment Mark on Camshaft Drive Gear
Pulley.
(3) Alignemnt Mark on Cylinder Head Cover LH.
6. Install crankshaft pulley temporarily and tighten
center bolt by hand (do not use a wrench).
Turn the crankshaft pulley clockwise to give some
belt slack between the crankshaft timing pulley
and the RH bank camshaft drive gear pulley.
2. Install pusher and tighten bolt to the specified torque.
Torque : 25 N·m (2.5 Kg·m/18 lb ft)
1. Install the pusher while pushing the tension pulley
to the belt.
2. Pull out pin from the pusher.
NOTE: When reusing the pusher, press the pusher with
approximately 100Kg to retract the rod, and insert a pin
(1.4 mm piano wire).
014RW011

Mar 18, 2009 | 2000 Isuzu Trooper

1 Answer

Timing for a 92 chevy geo tracker


Point the pulleys to there timing marks and point the dist. to #3 postion......

Oct 19, 2008 | 1992 Geo Tracker

Not finding what you are looking for?
1992 Geo Metro Logo

Related Topics:

274 people viewed this question

Ask a Question

Usually answered in minutes!

Top Geo Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Geo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...