Question about 2003 Chevrolet Venture Passanger

1 Answer

Left & right brake light not on

Chevrolet venture (2003)
when I brake, only the high mount brake light (LED) is on, the left & right side brake light is not on. fyse & bulbs are OK

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 91 Answers

Could be the brake switch that is mounted to the brake pedal area. Check if you have voltage out from there when brakes are applied, there may be two leads one for the high mount and one for regular brake lights.

Posted on Dec 07, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 s500 4matic Brake lights both led not working but center high mount is working what might be the problem. Is the brake switch bad?


If the high mount brake light is working, the brake light switch will be ok. The brake light circuit usually runs through the signal light switch on most vehicles. You may have a defective signal/multifunction switch causing this problem

Jul 28, 2015 | Cars & Trucks

1 Answer

The rear top brake light above the window works but the other two do not bulbs and fuses are good what could cause this and how do i fix it


I'm thinking that that truck has a dual brake switch.One is for the ABS,cruse,and high mount brake light.The other is for the left and right brake lights.

Apr 14, 2011 | 2003 Chevrolet TrailBlazer

1 Answer

Where is the brake light fuse both brake lights out not third


One of the fuses is located in the fuse panel on the right side of the dash. Open the passenger door for access. The other is located in the
fuse block under the hood on the right side near the washer reservoir.
It will be fuse #3. Hope this helps.

Mar 31, 2010 | 2003 Chevrolet Venture Passanger

1 Answer

How do i change a brake light bulb on 2000 vw jetta?


Removing:
  • Switch off all electrical consumers, switch off ignition key and remove ignition key.
  • Remove rear luggage compartment side panel trim (left or right).
98971821.gif
  • Remove 3 nuts, arrows, and remove housing.
  • Remove bulb holder.
Installing:
  • Install bulb holder.
  • Insert housing into body opening.
  • Tighten nuts.
  • Install applicable rear luggage compartment side panel trim.
Rear Light Bulb Holder Removing And Installing:
Removing:
  • Disconnect electrical connector.
  • Depress retainers, arrows, and remove bulb holder.
98971817.gif Installing:
  • Install in reverse order of removal.
And the Center Mounted Brake Lamp.
High mount Brake Light Removing And Installing:
The high mount brake light is installed in the rear shelf.
98971288.gif Removing:
  • Switch off all electrical consumers, switch off ignition key and remove ignition key.
  • Disconnect electrical connector from high mount brake light.
  • Remove rear shelf
  • Un-clip high-mount brake light from rear shelf, arrows.
  • Install in reverse order of removal.
NOTE: The bulb holder base plate contains soldered- in light emitting diodes (LEDs) that are not replaceable. In the event of LED malfunction, replace complete bulb holder.
Additional

Mar 13, 2010 | 2000 Volkswagen Beetle

2 Answers

Replacing high brake light bulb 2003 blazer


It's mounted up on the roof and held on with a screw on each end. There's a sticky gasket under it to keep the moisture out. Remove the two screws (usually phillips head, but sometimes torx 20 or 25) and persuade it come (peel essentially) off. Pull it out slowly to reveal the plug and unplug it. It's an LED strip so the whole thing will have to be replaced. Easily located on a popular auction based web site for about $50.

Feb 28, 2010 | 2003 Chevrolet Blazer

1 Answer

1999 GMC Envoy: replaced both GE 3057 lamps in left rear light assembly. Lamps both light. However depressing brake pedal does not initiate brake light. The righ rear brake light does work. The high mount...


The high mount brake light has its own fuse, so check that first. The high mount bulb is generally a stabdard type (there may be more than one bulb) or you can replace with an LED. As for the left rear bulbs not working when depressing brake pedal, check the bulbs again for any spring that may be broken. If the bulbs are still good, make sure there is sufficient contact with the socket. If still not working, have someone check it out further.

Feb 15, 2010 | 1999 GMC Jimmy

1 Answer

Left side brake light does not work.


do not touch the bulb its a special glass it will burn it out

Mar 16, 2009 | 2003 Chevrolet Venture Passanger

1 Answer

2003 chevy 2500hd no brake lights


your truck has fuses for the rear and high mount brake light in the fuse box in the side of the dash when you open the drivers door

Dec 23, 2008 | 2003 Chevrolet Silverado 2500HD

1 Answer

Chevy venture


Solution to your problem ... 1- I purchased from 1aauto.com a pair of Circuit Boards for my Chevy Venture 2003 for 85.00 $ ..free shipping 2 - I Installed them both , all lights now were not working at all. So I checked them and they were all burned ...So I purchased new ones ....Everything was working fine now but now my signal lights were not working left and right .....Checked the fuse box next to the passenger side door .... It was burned . Changed the fuse / Signals are working fine now ....All is good I just did this yesterday evening August 12, 2008 Conclusion ..Change everything going forward so you do not need to run around like I did from one store to another!
  1. Circuit Board : New
  2. Bulbs : New
  3. Fuses : New
Thank you

Jun 26, 2008 | 2003 Chevrolet Venture Passanger

Not finding what you are looking for?
2003 Chevrolet Venture Passanger Logo

Related Topics:

294 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

63242 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...