Question about 2000 Ford Expedition

1 Answer

Switch my ford exxpo into 4l or 4h and then back to normal. now the back tires grab when i turn.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 101 Answers

Thats odd. It would make more since if the front tires were grabbing. If there are NO signs that you are stuck in 4x4, then you may have a limited slip differential installed in the rear chunk. Normally when you turn a corner the inside when spins slower than the outside; the problem with that is when you get stuck, the differential acts like you are turning and sends all of the power to one wheel. So sometimes for traction, a limited slip differential is installed, so that when one of your tires starts to spin out, the differential locks up and sends power to both wheels. It is only supposed to do that when you are spinning a tire in the mud, or peeling out. But, sometimes the limited slip gets a little unlimited and needs to have new oil, or be replaced. You may also have a full locker, which is engaged by air or electric signal by a switch(sometimes the 4x4 switch), and it could be locked up. Either way, if they are locked up, when you turn both wheels will turn the same speed and you will know it. It could also be a brake problem. It would serve you best to have a proffessional look at it, as a brake problem is always a serious problem. Good luck!

Posted on Dec 07, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can i manualy take it out of 4x4


Those older fords you have to put the 4x4 selector into 2H or 2 High on the floor shifter. Then go to the front tires and in the very center of the tire there will be a knob that say Locked and Unlocked. Turn the knob to unlocked on both sides. Then you will not have front wheel dragging on the drive train and only the rear wheels will be the drive tire. TO put it back in 4x4. Turn the knob back to locked on each front tire and put the truck in 4H or 4 High to get 4x4. Only use 4L or 4Low when your stuck to prevent spinning your tires with full power.


Now if your has the automatic locking hubs I would switch them out with manual ones because the automatic ones were problematic where they get stuck or not work at all. It requires replacing the locking hub assembly which isn't that hard to do.

Feb 06, 2015 | 1990 Ford F150

1 Answer

How do i check the front axle vacuum selonoid on a 2002 jeep wrangler


02 , just sold mine, best car ever. had, of many.

how do you know that.?

and what are the tires, touching, (dirt, snow,ice, grass , pavement)

what?

this car has part time 4wd, it is not AWD

its not a Grand cheerokee with AWD.

engaging 4wd on ice free pavement is wrong.

http://www.rubicon-trail.com/4WD101/driveline-bind.html



and my fsm states.

read the operators guide in the glove box, it will say....

"2WD is intended to be driven on normal street and highway conditions, such as HARD surfaced roads."

Then

"4H & 4L positions are intended for loose slippery road surfaces only and not intended for normal driving" (They assume paved streets are normal.)

"Driving in 4H or 4L positions on hard surfaces roads, will cause, increased tire wear, and damage to the drive line components."

Unqual tire sizes, will do the same damage. "circumference mismatched"

Last: "do not attmpet to make a shift, while only the front or rear wheels are spinning" No transfer case synchronizer exists and damage will result."
(kill the gear dogs, you will)

May 26, 2014 | 2002 Jeep Wrangler

1 Answer

4L light


the motor has three bolts and a plug. They are pretty simple to do.

Jul 26, 2012 | 2007 Ford Explorer Eddie Bauer

1 Answer

1998 ford explorer auto, 4h,4l. stuck in 4l


Hello, Try keeping your foot on the brake pedal. Then shift the gearshift to neutral and then turn the 4x4 knob to the position you wish.

If this does not work, verify your rear brake lights are working. Then look under the dash at the top of the brake pedal lever and try to position the switch so that it works.

Then go back to my opening statement.

Jul 11, 2011 | 1998 Ford Explorer

1 Answer

HOW TO SHIFT TO 4 WHEEL DRIVE


Hi - Here is instruction how to do.

From N to 4H

Stop the vehicle completely, place the

transmission in "N" (Neutral) and depress

the brake pedal and the clutch pedal fully

(if equipped), then push in and turn the

switch to shift into "4H".

From 4H to 4H LOCK

You can operate the transfer switch either

when the vehicle is stopped or while the

vehicle is moving.

Position the front wheels straight ahead

and turn the switch to shift into "4H LOCK".

If the vehicle is moving, we recommend

that the speed be less than 100 km/h (60

mph) during this operation.

NOTE:

• When shifting between the transfer

switch position and the transfer gear

position is unmatched, all 4WD indicators

will blink and the buzzer will sound.

• If it is difficult to shift between "4H" and

"4H LOCK" while the vehicle is moving,

try accelerating and decelerating your

vehicle several times after turning the

transfer switch. Be sure to wait until traffic

conditions allow you to accelerate and

decelerate safety before using this procedure.

From 4H LOCK to 4L LOCK

Stop the vehicle completely, place the

transmission in "N" (Neutral) and depress

the brake pedal and the clutch pedal fully

(if equipped), then push in and turn the

switch to shift into "4L LOCK".

From 4L LOCK to 4H LOCK

Stop the vehicle completely, place the

transmission in "N" (Neutral) and depress

the brake pedal and the clutch pedal fully

(if equipped), then push in and turn the

switch to shift into "4H LOCK".

From 4H LOCK to 4H

You can operate the transfer switch either

when the vehicle is stopped or while the

vehicle is moving.

Position the front wheels straight ahead

and turn the switch to shift into "4H". If the

vehicle is moving, we recommend that the

speed be less than 100 km/h (60 mph) during

this operation.

NOTE:

• When shifting between the transfer

switch position and the transfer gear

position is unmatched, all 4WD indicators

will blink and the buzzer will sound.

• If it is difficult to shift between "4H" and

"4H LOCK" while the vehicle is moving,

try accelerating and decelerating your

vehicle several times after turning the

transfer switch. Be sure to wait until traffic

conditions allow you to accelerate and

decelerate safety before using this procedure.

From 4H to N

64J209

Stop the vehicle completely, place the

transmission in "N" (Neutral) and depress

the brake pedal and the clutch pedal fully

(if equipped), then push in and turn the

switch to the mark (1) at the left of the "N"
position, and hold the switch in this posi-

tion for 5 seconds until the "N" indicator

blinks, then turn the switch to the "N" position.

When you turn the transfer switch to the

"N" position, "N" indicator will come on with

the buzzer sound.

CAUTION

• Be sure to stop the vehicle completely

before operating the transfer

switch to shift between "N" and

"4H", or between "4H LOCK" and

"4L LOCK".

• Do not shift between "4H" and "4H

LOCK" unless the front wheels are

in the straight-ahead position and

we recommend that the vehicle

speed be less than 100 km/h (60

mph).

Do not operate the transfer switch

while tires are racing.

• Do not operate your vehicle in "4H

LOCK" or "4L LOCK" on dry, hard

surfaces.

(Continued)

CAUTION

(Continued)

• Do not operate the vehicle while a

4WD mode indicator is blinking

except when shifting between "4H"

and "4L LOCK".

If you operate the vehicle while a

4WD mode indicator is blinking, a

buzzer will sound and the transfer

will shift to "N" (Neutral) to prevent

transfer case damage.

In this case, use the following procedure.

1) Depress the clutch pedal fully (if

equipped) or shift the automatic

transmission gearshift lever to the

"N" position.

2) Turn the transfer switch to the

position previously selected.
3) Operate the transfer switch again.

Feb 01, 2011 | 2007 Suzuki Grand Vitara 4WD

2 Answers

4runner 92 4WD problem


This might sound like a silly question but did you put the truck in neutral before you shifted into 4L ? Reason being transfer case damage can occure if it wasnt in neutral when you shifted into 4L.

May 10, 2010 | 1992 Toyota 4Runner

1 Answer

How do I use the 4 wheel drive on my Ford Ranger XLT 2.5 TDi 2004


4L only to be used in extreme condtions
N
4H for off road/snow/ice
2H - normal driving

when switching to 4H vehicle must be stationary, as when changing from 4H to 4L
but it is possible to change from 4H back to 2H while in motion.
when 4wd is engaged a lamp will illuminate on dials telling that the hubs are free wheeling, when changing back to 2H you must press corresponding switch to dis-engage this function

Jan 08, 2010 | 2004 Ford Ranger

1 Answer

1984ford f150 Ido not know how to put the truck into 4wheel drive


There should be a lever shifter on the floor board with 2h- 4h-4L on the knob. Pull or push the lever to 4H then get out and go to the front axle. In the middle of the front tires there should be a locking front hub assembly, turn the selector to lock, do this on both wheels, your truck should now be in 4 wheel drive. To put it in 4L you need to havt the transmission in nuetral before you shift the lever. Once done playing make sure you unlock your front axel(hubs) and place the lever in 2H.

Oct 25, 2009 | 1984 Ford F 150

1 Answer

98 expedition xlt wont engage in 4h or 4l. the awfs light is on when switch in that position, none of the others do (eg. 4H or 4L) the vehicle has not been in 4wd in a few months. last time 2low engaged...


one the transfer case there is a motor on the back side of the transfer case. most of the time that goes bad. if you don't have a trouble shooting guide with a wiring diagram, best to have a mech have a look at it. most of the time they rust and stick if not used a few times a year. best of luck.

Aug 06, 2009 | 1998 Ford Expedition

Not finding what you are looking for?
2000 Ford Expedition Logo

118 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...