Question about 2006 Dodge Sprinter

3 Answers

ABS, ESP & ASR Lights Stay on

2005 Dodge Sprinter, 2500, ~50,000 miles
I had some trouble earlier with a bad trailer harness--it blew the brake light fuse and caused the ABS, ESP and ASR lights to come on and I had to manually release the shift lever. That was corrected. Suddenly the same three lights have come on. The brake lights are working and I can shift without manually releasing the shift lever. Are there some simple things to check to correct this? Brake fluid is ok and so are the brake pads

Posted by on

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 341 Answers

Hi The best place to start is by checking all the fuses inside and under hood . If a fuse from a diffrent circuit blows it can cause these lights to come on.

Posted on Dec 06, 2008

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 399 Answers

Chances are its either worn brakes or possibly a wheel speed sensor.. likely thr rear abs speed sensor in the differential, usually costs about $35 at the Dodge dealer and takes 20 minutes to change yourself, then disconnect battery for 10 seconds and the system will reset  for further help
You need to have the car checked for trouble codes

Posted on Dec 06, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 2,920 Answers

You need to have a diagnosic run on it to see what codes come up.the wiring harness could be the cause of the problem

Posted on Dec 06, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a red dash light lit. It is an exclamation in a trialngle with a counter clockwise circle around it. Can anyone tell me what it means? I drive an Audi A4 2005


ASR - Acceleration Skid Control system.
When ASR warning light blinking the system is activated itself for car acceleration skid control.

For today's typical high-torque engines, traction control (ASR) can increase both comfort and safety, particularly when driving on slippery roads or surfaces offering differing levels of grip. Traction control permits smooth starting and acceleration through the full speed range without wheel-spin or fishtailing.

tdisline_338.jpg


ASR only operates in conjunction with the electronic accelerator (E-gas) and uses components of the anti-lock braking system (ABS). If one wheel suddenly begins to rotate faster than the others (slip), ASR intervenes in the engine management system and reduces power until the wheel stops spinning.
The ASR system represents a further contribution to active safety as it maintains vehicle traction and directional stability throughout the acceleration phase at any speed. In addition, it reduces tyre wear. Activation of the ASR system is indicated by a flashing indicator lamp in the instrument cluster.
The ESP system means the Electronic Stability Program. If the ESP lights on the dashboard permanently the ESP system is faulty. You must access the ESP Electronic Control Unit (ECU) memory for pull out all DTC (Diagnostic Trouble Codes), using diagnostic equipment connected to the data link connector of the car. Then you will be full informed about bad pieces (e.g.: front right wheel abs sensor interrupted, ...). After bad pieces replacement you will be able to erase all faults memored by ESP ECU, in other words reset the ESP system and turn off the warning lamp on dashboard.

Sep 27, 2011 | 2005 Audi A4

2 Answers

A circle with a triangle sign appears on the dashboard appears


ASR - Acceleration Skid Control system.
When ASR warning light blinking the system is activated itself for car acceleration skid control.

For today's typical high-torque engines, traction control (ASR) can increase both comfort and safety, particularly when driving on slippery roads or surfaces offering differing levels of grip. Traction control permits smooth starting and acceleration through the full speed range without wheel-spin or fishtailing.

tdisline_338.jpg


ASR only operates in conjunction with the electronic accelerator (E-gas) and uses components of the anti-lock braking system (ABS). If one wheel suddenly begins to rotate faster than the others (slip), ASR intervenes in the engine management system and reduces power until the wheel stops spinning.
The ASR system represents a further contribution to active safety as it maintains vehicle traction and directional stability throughout the acceleration phase at any speed. In addition, it reduces tyre wear. Activation of the ASR system is indicated by a flashing indicator lamp in the instrument cluster.
The ESP system means the Electronic Stability Program. If the ESP lights on the dashboard permanently the ESP system is faulty. You must access the ESP Electronic Control Unit (ECU) memory for pull out all DTC (Diagnostic Trouble Codes), using diagnostic equipment connected to the data link connector of the car. Then you will be full informed about bad pieces (e.g.: front right wheel abs sensor interrupted, ...). After bad pieces replacement you will be able to erase all faults memored by ESP ECU, in other words reset the ESP system and turn off the warning lamp on dashboard.

Sep 16, 2011 | 1999 Volkswagen Passat

1 Answer

I have an Audi a4 2001 1.8t and the asr light its flashing, thanks for your help my name is Marcos Aguilar


ASR - Acceleration Skid Control system.
When ASR warning light blinking the system is activated itself for car acceleration skid control.

For today's typical high-torque engines, traction control (ASR) can increase both comfort and safety, particularly when driving on slippery roads or surfaces offering differing levels of grip. Traction control permits smooth starting and acceleration through the full speed range without wheel-spin or fishtailing.
tdisline_338.jpg


ASR only operates in conjunction with the electronic accelerator (E-gas) and uses components of the anti-lock braking system (ABS). If one wheel suddenly begins to rotate faster than the others (slip), ASR intervenes in the engine management system and reduces power until the wheel stops spinning.
The ASR system represents a further contribution to active safety as it maintains vehicle traction and directional stability throughout the acceleration phase at any speed. In addition, it reduces tyre wear. Activation of the ASR system is indicated by a flashing indicator lamp in the instrument cluster.

The ESP system means the Electronic Stability Program. If the ESP lights on the dashboard permanently the ESP system is faulty. You must access the ESP Electronic Control Unit (ECU) memory for pull out all DTC (Diagnostic Trouble Codes), using diagnostic equipment connected to the data link connector of the car. Then you will be full informed about bad pieces (e.g.: front right wheel abs sensor interrupted, ...). After bad pieces replacement you will be able to erase all faults memored by ESP ECU, in other words reset the ESP system and turn off the warning lamp on dashboard.


Check & replace if necessary the brake pedal switch placed above pedals on the support.
If the problem still occurs you might access the ABS ECU (Electronic Control Unit) using diagnostic equipment (VAS, VAG-Com, or similar) connected to the data link connector of the car, in order to pull out all DTC's (Diagnostic Trouble Code) memored. Then you will be able to replace bad piece(s) and fix the problem by erasing all DTC's stocked inside ABS ECU & reset it.


Good Luck!

Sep 07, 2011 | 2001 Audi A4

1 Answer

VW BEETLE , ASR LIGHT IS ON , AT SAME TIME THERE SEEMS TO BE A GROANING WHEEL BEARING NOISE AT LOW SPEED , COULD THIS BE CONNECTED ? WHAT IS ASR??


First of all replace bad wheel bearing !!! This bad wheel bearing causes ASR light ON.

ASR - Acceleration Skid Control system.
When ASR warning light blinking the system is activated itself for car acceleration skid control.


For today's typical high-torque engines, traction control (ASR) can increase both comfort and safety, particularly when driving on slippery roads or surfaces offering differing levels of grip. Traction control permits smooth starting and acceleration through the full speed range without wheel-spin or fishtailing.

tdisline_672.jpg


ASR only operates in conjunction with the electronic accelerator (E-gas) and uses components of the anti-lock braking system (ABS). If one wheel suddenly begins to rotate faster than the others (slip), ASR intervenes in the engine management system and reduces power until the wheel stops spinning.
The ASR system represents a further contribution to active safety as it maintains vehicle traction and directional stability throughout the acceleration phase at any speed. In addition, it reduces tyre wear. Activation of the ASR system is indicated by a flashing indicator lamp in the instrument cluster.

The ESP system means the Electronic Stability Program. If the ESP lights on the dashboard permanently the ESP system is faulty. You must access the ESP Electronic Control Unit (ECU) memory for pull out all DTC (Diagnostic Trouble Codes), using diagnostic equipment connected to the data link connector of the car. Then you will be full informed about bad pieces (e.g.: front right wheel abs sensor interrupted, ...). After bad pieces replacement you will be able to erase all faults memored by ESP ECU, in other words reset the ESP system and turn off the warning lamp on dashboard.

Jun 24, 2011 | 2001 Volkswagen Beetle

1 Answer

ABS light came on with a triangle and a circle around it with an arrow on the end. what does that mean?


ASR - Acceleration Skid Control system.
When ASR warning light blinking the system is activated itself for car acceleration skid control.

For today's typical high-torque engines, traction control (ASR) can increase both comfort and safety, particularly when driving on slippery roads or surfaces offering differing levels of grip. Traction control permits smooth starting and acceleration through the full speed range without wheel-spin or fishtailing.

tdisline_644.jpg


ASR only operates in conjunction with the electronic accelerator (E-gas) and uses components of the anti-lock braking system (ABS). If one wheel suddenly begins to rotate faster than the others (slip), ASR intervenes in the engine management system and reduces power until the wheel stops spinning.
The ASR system represents a further contribution to active safety as it maintains vehicle traction and directional stability throughout the acceleration phase at any speed. In addition, it reduces tyre wear. Activation of the ASR system is indicated by a flashing indicator lamp in the instrument cluster.
The ESP system means the Electronic Stability Program. If the ESP lights on the dashboard permanently the ESP system is faulty. You must access the ESP Electronic Control Unit (ECU) memory for pull out all DTC (Diagnostic Trouble Codes), using diagnostic equipment connected to the data link connector of the car. Then you will be full informed about bad pieces (e.g.: front right wheel abs sensor interrupted, ...). After bad pieces replacement you will be able to erase all faults memored by ESP ECU, in other words reset the ESP system and turn off the warning lamp on dashboard.

Jun 08, 2011 | 2004 Volkswagen Passat

1 Answer

What is the following warning symbol. Yellow triangle in a yellow circle, with squiglly lines in it?


ASR - Acceleration Skid Control system.
When ASR warning light blinking the system is activated itself for car acceleration skid control.


For today's typical high-torque engines, traction control (ASR) can increase both comfort and safety, particularly when driving on slippery roads or surfaces offering differing levels of grip. Traction control permits smooth starting and acceleration through the full speed range without wheel-spin or fishtailing.

tdisline_532.jpg


ASR only operates in conjunction with the electronic accelerator (E-gas) and uses components of the anti-lock braking system (ABS). If one wheel suddenly begins to rotate faster than the others (slip), ASR intervenes in the engine management system and reduces power until the wheel stops spinning.
The ASR system represents a further contribution to active safety as it maintains vehicle traction and directional stability throughout the acceleration phase at any speed. In addition, it reduces tyre wear. Activation of the ASR system is indicated by a flashing indicator lamp in the instrument cluster.

The ESP system means the Electronic Stability Program. If the ESP lights on the dashboard permanently the ESP system is faulty. You must access the ESP Electronic Control Unit (ECU) memory for pull out all DTC (Diagnostic Trouble Codes), using diagnostic equipment connected to the data link connector of the car. Then you will be full informed about bad pieces (e.g.: front right wheel abs sensor interrupted, ...). After bad pieces replacement you will be able to erase all faults memored by ESP ECU, in other words reset the ESP system and turn off the warning lamp on dashboard.

May 13, 2011 | Volkswagen Passat Cars & Trucks

1 Answer

On a 2001 beetle, What does the triangle light with explanation mark in it mean


ASR - Acceleration Skid Control system.
When ASR warning light blinking the system is activated itself for car acceleration skid control.


For today's typical high-torque engines, traction control (ASR) can increase both comfort and safety, particularly when driving on slippery roads or surfaces offering differing levels of grip. Traction control permits smooth starting and acceleration through the full speed range without wheel-spin or fishtailing.

tdisline_445.jpg
ASR only operates in conjunction with the electronic accelerator (E-gas) and uses components of the anti-lock braking system (ABS). If one wheel suddenly begins to rotate faster than the others (slip), ASR intervenes in the engine management system and reduces power until the wheel stops spinning.
The ASR system represents a further contribution to active safety as it maintains vehicle traction and directional stability throughout the acceleration phase at any speed. In addition, it reduces tyre wear. Activation of the ASR system is indicated by a flashing indicator lamp in the instrument cluster.

The ESP system means the Electronic Stability Program. If the ESP lights on the dashboard permanently the ESP system is faulty. You must access the ESP Electronic Control Unit (ECU) memory for pull out all DTC (Diagnostic Trouble Codes), using diagnostic equipment connected to the data link connector of the car. Then you will be full informed about bad pieces (e.g.: front right wheel abs sensor interrupted, ...). After bad pieces replacement you will be able to erase all faults memored by ESP ECU, in other words reset the ESP system and turn off the warning lamp on dashboard.

Apr 13, 2011 | 2001 Volkswagen Beetle

1 Answer

I have a yellow triangle light that appears on the dash intermitanly on a 2000 volkswago passat. What could this be? Thanks Lisa


The ESP system means the Electronic Stability Program. If the ESP lights on the dashboard permanently the ESP system is faulty. You must access the ESP Electronic Control Unit (ECU) memory for pull out all DTC (Diagnostic Trouble Codes), using diagnostic equipment connected to the data link connector of the car. Then you will be full informed about bad pieces (e.g.: front right wheel abs sensor interrupted, ...). After bad pieces replacement you will be able to erase all faults memored by ESP ECU, in other words reset the ESP system and turn off the warning lamp on dashboard.

tdisline_292.jpg
ESP system includes ASR - Acceleration Skid Control system.
When ASR warning light blinking the system is activated itself for car acceleration skid control.

For today's typical high-torque engines, traction control (ASR) can increase both comfort and safety, particularly when driving on slippery roads or surfaces offering differing levels of grip. Traction control permits smooth starting and acceleration through the full speed range without wheel-spin or fishtailing.
ASR only operates in conjunction with the electronic accelerator (E-gas) and uses components of the anti-lock braking system (ABS). If one wheel suddenly begins to rotate faster than the others (slip), ASR intervenes in the engine management system and reduces power until the wheel stops spinning.
The ASR system represents a further contribution to active safety as it maintains vehicle traction and directional stability throughout the acceleration phase at any speed. In addition, it reduces tyre wear. Activation of the ASR system is indicated by a flashing indicator lamp in the instrument cluster.


Please do rate my response. Thnaks!

Feb 20, 2011 | 2005 Volkswagen Passat

1 Answer

ASR light blinking


ASR - Acceleration Skid Control system.
When ASR warning light blinking the system is activated itself for car acceleration skid control.
For today's typical high-torque engines, traction control (ASR) can increase both comfort and safety, particularly when driving on slippery roads or surfaces offering differing levels of grip. Traction control permits smooth starting and acceleration through the full speed range without wheel-spin or fishtailing.

tdisline_191.jpg
ASR only operates in conjunction with the electronic accelerator (E-gas) and uses components of the anti-lock braking system (ABS). If one wheel suddenly begins to rotate faster than the others (slip), ASR intervenes in the engine management system and reduces power until the wheel stops spinning.
The ASR system represents a further contribution to active safety as it maintains vehicle traction and directional stability throughout the acceleration phase at any speed. In addition, it reduces tyre wear. Activation of the ASR system is indicated by a flashing indicator lamp in the instrument cluster.
The ESP system means the Electronic Stability Program. If the ESP lights on the dashboard permanently the ESP system is faulty. You must access the ESP Electronic Control Unit (ECU) memory for pull out all DTC (Diagnostic Trouble Codes), using diagnostic equipment connected to the data link connector of the car. Then you will be full informed about bad pieces (e.g.: front right wheel abs sensor interrupted, ...). After bad pieces replacement you will be able to erase all faults memored by ESP ECU, in other words reset the ESP system and turn off the warning lamp on dashboard.


Please do rate my response. Thnaks!

Jan 25, 2011 | 2005 Volkswagen Passat

1 Answer

Yellow circle with triange flashing


For today's typical high-torque engines, traction control (ASR) can increase both comfort and safety, particularly when driving on slippery roads or surfaces offering differing levels of grip. Traction control permits smooth starting and acceleration through the full speed range without wheel-spin or fishtailing.

tdisline_86.jpg
ASR only operates in conjunction with the electronic accelerator (E-gas) and uses components of the anti-lock braking system (ABS). If one wheel suddenly begins to rotate faster than the others (slip), ASR intervenes in the engine management system and reduces power until the wheel stops spinning.
The ASR system represents a further contribution to active safety as it maintains vehicle traction and directional stability throughout the acceleration phase at any speed. In addition, it reduces tyre wear. Activation of the ASR system is indicated by a flashing indicator lamp in the instrument cluster.


The ESP system means the Electronic Stability Program. If the ESP lights on the dashboard permanently the ESP system is faulty. You must access the ESP Electronic Control Unit (ECU) memory for pull out all DTC (Diagnostic Trouble Codes), using diagnostic equipment connected to the data link connector of the car. Then you will be full informed about bad pieces (e.g.: front right wheel abs sensor interrupted, ...). After bad pieces replacement you will be able to erase all faults memored by ESP ECU, in other words reset the ESP system and turn off the warning lamp on dashboard.

Dec 09, 2010 | Audi A4 Cars & Trucks

Not finding what you are looking for?
2006 Dodge Sprinter Logo

Related Topics:

759 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

63291 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...