Question about 1997 Jaguar XJ6

1 Answer

Need to program key after new batery fiffed - 1997 Jaguar XJ6

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Jagbits.com has all the programming instructions for all the cars....depends on what year your car is what the instructions are. Try this link: http://www.jagbits.com/reprogram.html

Kittylvr

Posted on Dec 09, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Changing a battery on Ford galaxy 2.0 2007


hi just to make you aware that you might need a constant circit wich meens you need to yous jump leeds from the terminals of the car to the batery that your fiting before you disconect old one no need for re programing key ect

Jan 22, 2013 | 2007 Ford Galaxy 2.0

1 Answer

Abs light & traction control fault on dash after new battery was fiffed


Probably lose of power codes. you can have them erased, or they will go out eventually

Apr 19, 2011 | Jaguar S-Type Cars & Trucks

1 Answer

I have passat 1.9 tdi variant,2001. year.my batery is dead.when i take a new batery i was missing code for radio in car.type of radio is vw gamma.when i switch radio on, on the display write safe.please...


How to exit the 1998 VW Passat radio out of SAFE mode:
IMPORTANT NOTE: You must have the security anti-theft code for your VW radio from the car manufacturer, or from a VW dealer!
The sequence of radio programming is:
1. Push simultaneous "SCAN" and "RDS" keys until on the screen will appear "1000" displayed.
2. Release keys. No more push on "SCAN" and "RDS" keys because otherwise number "1000" will be considered as first safe code attempt.
3. By the #1 key you will set up the first safe code digit.
4. By the #2 key you will set up the second safe code digit.
5. By the #3 key you will set up the third safe code digit.
6. By the #4 key you will set up the four-th safe code digit.
7. Then push again simultaneous "SCAN" and "RDS" keys for confirm this safe code. On the screen will be displayed "SAFE" notice. Release keys! For few seconds a radio frequence will be displayed. The radio is now ready for use!

Dec 05, 2010 | 1999 Volkswagen Passat

1 Answer

The theft ligth is on and my truck does not start


YOU HAVE A TRANSPONDER KEY THAT NEEDS TO BE RE-PROGRAMED

Apr 24, 2010 | 2001 Ford F150 Styleside SuperCrew

2 Answers

Had dead battery in 2002 honda civic got jump now word CODE in radio display


try disconecting the positive terminal of the batery for sevral minets (5-10) this will reset the brain box memory for the stero aswell as for the car it self.

what caused the batery to go dead in the first place?
things that i can think of :
1) left headlights on over night
2) bad altenator not charging batery
3) battery is old and not taking a charge anymore
4) new stero installed incorectly and drainging the batery
have you resently installed a new stero or amplifyer?
is the turn key igntion system hooked into the amp/stero antena lead so that thy are shut of when the ignition is?
of note: new streo >theres a blue wire marked ant that goes to the amplifyer if not there you need to find the orange accsesory wire coming from the turn key igntion>check for power when ignition is in the on & off states could be yellow in some cars but is usaly orange if this wire has on and of state controled by the turn key igntion this would be the wire to tap into for the amplyfire and the radio main power
check your radio's instaltion guide for code errors
its posible that when hooking up the jump it was done incorectly and blew up the radio
ie postive and negative where fliped
hope this helped :)

Feb 24, 2010 | 2002 Honda Civic

1 Answer

The remomte control is not working after the high temperatures of yesterday With the key we can open de the doors but despite of the new batery in the remote it is nog functioning


Ok here are the programming instructions for the remote, follow them exactly, no missed steps, if this doesn't correct the issue the remote is defective most likely.

  1. Remove key from ignition.
  2. Close all doors.
  3. Open driver side door and leave open.
  4. Perform the following steps within 24 seconds.
    a. Insert key in ignition.
    b. Turn key to ON and OFF.
    c. Repeat step b two more times.
    d. Remove key.
    e. Push driver door frame button three times (black rubber button located on driver door frame that tell the vehicle whether or not door is closed.)

5. Buzz sound, chime or doors will lock and unlock should be heard at this point signaling that the vehicle is now in
programming mode. If not, wait 40 seconds and return to step 4.


6. All transmitters need to be programmed at this time, including the old ones. Push any button on the transmitter
two times. A buzz sound, chime or doors locking and unlocking should be heard at this point signaling that the
vehicle has accepted the new transmitter code. If there is only one transmitter, repeat this step two more times
using the only transmitter. If there are two transmitters, repeat this step two more times using the second
transmitter.

7. Push driver door frame button one time. Two buzz sounds, chimes or doors locking and unlocking 2 times should
be heard at this point signaling successful programming.

Aug 07, 2009 | 2003 Mazda MPV

1 Answer

2004 Toyota Camry key fob programation


sit in car all doors closed put key in ignition and turn from OFF to ACC 3 times as fast as you can leaving it in ACC on the last cycle then press your remote button. your blinkers should flash to tell you this has worked.... may take you a couple of tries to get it!!

Jun 06, 2009 | 2004 Toyota Camry

1 Answer

I need to put new baterys in my key fob for my renault megan coupe 1998 can i just swap the baterys at home thank you


go to any auto or batteries stores and they will replace the batteries for u.....or u can do it yourself....

Mar 07, 2009 | 1986 Renault Sport

2 Answers

I just locked my keys in my 1995 toyota corolla dx and i dont have AAA and i dont have $70 for a locksmith. Is there anyway to open my door?


bend a wire coat hanger and slid if down betwen the window and door fish around tilllllll u hook yhe lock and pull up

Jan 20, 2009 | 1998 Toyota Corolla

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Raygin
Raygin

Level 2 Expert

322 Answers

yadayada
yadayada

Level 3 Expert

61037 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...