Question about 2001 Ford Ranger Regular Cab

1 Answer

Replaced clutch & slave cylinder on 2001 ford ranger can't bleed

Replaced

Posted by on

  • Walter Whitaker
    Walter Whitaker May 11, 2010

    need more info. Probably air in the slave cylinder. They are a real pain. I have one out right now.

  • Anonymous Mar 18, 2014

    replace clutch slave cylinder

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 25 Answers

Do a web search on it, and it will tell you the proper way to bleed it.

Posted on Dec 06, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to bleed 89 ford ranger 4x4 clutch


there is a bleeder screw by the transmission slave cylinder that you bleed the air out.just pump the clutch pedal a few times hold the pedal to the floor and have someone crack open the bleeder screw to bleed the air out then close it and repeat.make sure the master cylinder for the clutch doesn`t go low.

Nov 02, 2011 | 1989 Ford Ranger

1 Answer

How do i bleed my slave cylinder in my 1993 ford ranger. cause it is hard to get in and out of gear, or do u think it may be something else.... thanks


you can not bleed it
replace it after this test
pump the clutch 25 times with the engine off
If you do get a pedal with the clutch to shift the slave cylinder is shot
have the slave clylinder full before doing this test

Mar 16, 2011 | Ford Ranger Cars & Trucks

2 Answers

2002 ,90k ,slave cylinder is leaking,How to solve ?


the easyest is to just put another slave cyl on it

Nov 22, 2009 | 2001 Ford Ranger Regular Cab

3 Answers

2001 Ford ranger edge. The gears won't change.


The trans will need to come out. While your at it, just replace the clutch assembly, rear main oil seal, resurface the flywheel, and the clutch master cyl. Its not really a job you should do, find a repair shop to handle it.

Nov 06, 2009 | Ford Edge Cars & Trucks

1 Answer

I have A 1998 FORD RANGER EXT. CAB W/ 6 CYL.- 4.0 RECENTLY LOST PEDAL ON MY CLUTCH. REPLACED MASTER CYLINDER, SLAVE CYLINDER, AND THE CLUTCH PACK, HAVE FLUID THROUGH BLEEDER VALVE ON THE SLAVE BUT CAN NOT...


Take the top off the master cyl and slowly very slow push in on the clutch and watch for any bubbles comming up.Replace the top and pump pressure and bleed at the master direct by using the lines for bleeders.

Aug 13, 2009 | 1998 Ford Ranger SuperCab

1 Answer

Should it take more than 30 min to bleed the slave cylinder


get it to where it will work and drive it a while it will work its way out .

Jan 25, 2009 | 2001 Ford Ranger Regular Cab

2 Answers

89 ranger manual trans slipping already replace clutch and slave cylinder? still slipping any help?


Manual transmissions do not slip ie. when the gears mesh, there is no slip unless they strip out and make an awful noise and will not pull henceforth.

You probably still have a slipping clutch plate against the flywheel. You need to adjust the clutch petal linkage shaft to allow the pressure plate to be release from the thrust bearing, ie shorten the shaft length.. If you and most likely you do just have the clutch release slave cylinder that releases the clutch when you apply the petal. You need to bleed the slave cylinder of any excess fluid or air that may have entered the line if you opened it at any point. You need to bleed it as you would a break cylinder and this should fix ya.
good luck.
good luck

Jan 05, 2009 | 1989 Ford Ranger

1 Answer

New slave cylander, can't get hydraulic preasure.


mechanics bodge this one ,slacken bleed nipple and hold finger on end then shout to mrs to push pedal down ,you then shout hold it down ,and apply a bit of pressure on nipple and then shout up,wait 5 secs for fluid to refill in master cylinder and repeat this 6/7 times then you should have some pressure ,maybe only a little bit but it becomes easier to bleed .if this doesnt work blame mrs throw a wobbly and throw her in the pool or fishpond and buy a new master cylinder or re rubber it and repeat again but i guarentee it will work then as she will be praying so hard to allah--- the almighty one will make it happen for you

Nov 16, 2008 | 2001 Ford Ranger Regular Cab

1 Answer

2001 ford ranger clutch


have you check the slave cylinder to see if its moving when someone puts there foot on the clutch.
And check the adjustment on the master cylinder.

Sep 18, 2008 | 2001 Ford Ranger Regular Cab

Not finding what you are looking for?
2001 Ford Ranger Regular Cab Logo

311 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

71525 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22059 Answers

Ron Lankford

Level 3 Expert

5386 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...