Question about 2003 Pontiac Grand Am

1 Answer

Electrical is their suppose to be power to all the fuses both sides when the fuse is pulled out and ignition switch is in the off position. 11.84 one side and 5.16 on the other side.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 81 Answers

Tell me exactly what your problem is and let's forget about fuses for the time being.

Posted on Dec 28, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Turn signal windshield wipers radio windows doorlocks all not working -fuses are all ok


Remind me not to ask for a ride from you. When you jiggle the key you are probably connecting, or re-connecting, the power from the ignition switch to that portion of the fuse panel that covers all those things that don't work. Except for the power door locks- that may be a separate issue. But everything else only has power when the key is in on (run) or start. And the fuses to them only have power from the ignition switch when the position is in on or run. You have a bad, worn lock cylinder, or a bad electrical portion of the ignition switch. You'd have to pull the cover shrouds off the steering column to see and get to the parts.

Sep 29, 2015 | 2001 Dodge Stratus

2 Answers

Daewoo lanos 2000 .no fuel or spark. Turns over but no go. Removed fuel pump tested it .it works.reinserted and nothing. Help


K had a simular problem a while back anx found that the ground to the ecu was lost after simply fitting a cable from a ground point to the ecu housing the veichle started right up after that i heard that it was a common fault on earlier dawoos

Jan 21, 2015 | Daewoo Cars & Trucks

2 Answers

No power to ignition switch


check the fuses and the relays. and finally the ignition switch, its rare but the little wires get loose or broken, and send no electrical power to the switch

Nov 20, 2013 | 1988 Ford F 150

1 Answer

Wiper wiring diagram


Those are accessory functions working off the ignition switch when in accessory position or run position of the key. Were you to check if the wiper and radio fuse had power to them in the run or accessory position as they should, likely they would not. Power from the switch goes to the fuse panel, powering the fuses and circuits that only work with key in on or acc., either a direct wire to the fuse panel or sometimes, fuses get power from an accessory relay that sends power to fuses, but relay has to get a signal from a good working switch before it powers the fuses.
What I'm trying to say, is the bad switch is probably the reason you have no wipers, radio, or mirrors.

Aug 31, 2013 | Cars & Trucks

2 Answers

Car turns over but won't start fuel injector fuse and ignition fuses are good but no power is getting to them. also the stereo and wipers only work when ignition is on accessory. when its on r


Sounds like it could be a bad ignition switch-the electrical part, not the lock cylinder. When key is in the on position (run), those fuses should be powered. Are all the maxi-fuses good? They distribute power throughout the car's electrical circuits-like the fuse panel, for instance, so check the maxi-fuses. If good, probably the ignition switch is bad.

Apr 03, 2013 | 1997 Pontiac Grand Am

1 Answer

I need a wiring diagram for 1995 2500 6.5 turbo diesel electric fuel pump circuit


The primary (coils) side of the fuel pump relay is powered by the CRANK fuse (10 Amp) located in the instrument panel fuse block. This fuse is hot ONLY when the ignition switch is in the CRANK position. The secondary (contact) side of the relay is powered by the ECM-B fuse (20 Amp) which is hot at all times. This fuse is located in the engine compartment fuse block. The electric fuel pump in the tank only operates during engine cranking.

Feb 19, 2012 | 1995 Chevrolet Silverado 2500

1 Answer

Changing out ignition switch


    Remove the Ignition Switch
  1. Disconnect the negative battery cable with a socket or box wrench. Pull the airbag fuse from the driver's side fuse panel using the fuse removal tool found on the panel. Disable the theft-lock system on the radio.

  2. Remove the instrument cluster by removing the bezel screws with a screwdriver and prying the bezel off with a prying tool or flathead screwdriver.

  3. Remove the two screws holding the ignition switch in place with a screwdriver.

  4. Push the ignition switch about one inch toward the front of the vehicle so that it will clear the mounting bracket. Lift the switch up and out from behind the instrument panel.

  5. Disconnect the electrical connectors from the ignition switch. Put the key in the ignition and turn it the Run position.

  6. Press the spring-loaded pin on the side of the ignition switch with a small screwdriver. Pull the lock cylinder out by the key.

  7. Install the New Ignition Switch
  8. Place the ignition key in the new ignition cylinder and push the cylinder into place in the ignition housing. Turn the key to the off position and remove it.

  9. Connect the electrical wires to the back of the ignition switch.

  10. Put the switch assembly in position in the cluster and install and tighten the two screws with a screwdriver.

  11. Install the instrument cluster bezel and attach the two screws with a screwdriver.

  12. Replace the airbag fuse in the driver's side fuse panel. Connect the negative battery cable with a wrench. Enter the code for the Theft-lock system into the radio.

Mar 09, 2011 | 2002 Oldsmobile Alero

1 Answer

Why wont my dashboardlights and radio not work. I have cheecked the fuses.


Did you check for battery power at the fuses, or did you give them the "Eyeball Test". The two fuses involved in your problem are fuse "O" and fuse "H". Fuse "O" will only have battery power when the ignition switch is in the "ACC" or "ON" positions. Fuse "H" will have battery power at all times. If both of these fuses have battery power when they are supposed to, the problem is probably your illumination control switch is either defective or turned off. If fuse H has no power, the problem is in the main wiring harness between the battery and the fuse block. If fuse "O" does not have power when it is supposed to, the problem is most likely your ignition switch.

Jan 11, 2011 | 1994 Nissan Sentra 4-Door

1 Answer

I want to hook up my XM radio receiver to tun off with the ignition switch. I purchased a lighter plug kit to wire into the ignition switch, but after pulling fuse panel I'm not sure what wire color to tap...


using a test light or meter locate a fuse that does not have power when the switch is off - xm should require only 5 amp fuse - no more than 10 - pull fuse to test which side the power is coming in and hook into load side of fuse-

Sep 27, 2009 | 2007 Saturn VUE FWD 4

1 Answer

I have no power going to my ignition. I have 12.87 volts in the battery, lights work, all fuses are good. Everything that goes through the ignition doesn't work, i.e. starter, radio, door locks, windows,...


See if you have 12 volts to the starter if you do then check the fuse on the battery that Toyota uses for the ignition switch if I remember correctly there are two huge fuses and they can blow on occasion, also pull the fuse apart on the battery cable positive side and clean all parts with sand paper and put it back together and try starting it. If that does not work then check the fuses and relays in the relay box, also be sure the negative side post is clean too. If you still don't get power to the switch then you may have a bad switch or a loose wire on the starter solenoid

Jul 19, 2009 | 1995 Toyota Camry

Not finding what you are looking for?
2003 Pontiac Grand Am Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...