Question about 2001 Jaguar XJ8

1 Answer

Jaguar XJ8-X308 3.2 litre year 2000.

How do I remove the centre console/arm rest

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 14 Answers

Its just 2 crosshead screws by the hinge(when fully open) & then angle it forward to release the check strap.

Posted on Dec 13, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need diagram of 2000 jaguar xj8 cylinder diagram


the cylinder numbering changed at 2000 model year before 2000 rh cylinders viewed sat in drivers seat 1357 lh 2468 after 2000 rh 1234 lh 5678

May 06, 2017 | Jaguar XJ8 Cars & Trucks

1 Answer

My xj8 Jaguar crank up and sets right back off what all could be wrong


Security is set. Could be one problem. Fuel system can do this, but rarely. Takes a scanner to see where to look first.

Dec 30, 2015 | Jaguar Cars & Trucks

1 Answer

2002 jaguar xj8 when I drive it won't go over 3000rpm


Jaguar wont rev 3000 rpm Questions & Answers - Fixya

www.fixya.com > Forum > Tags > wont rev 3000 rpm
1998 Jaguar XJ8 won't rev over 3000 rpm ... Wont go beyong 3000 Revs s type 2001, wont go beyond 3000 Revs and it' in limp ... Question about 2002 X-Type ... My jaguar xjr8 year 2000 battery went dead started car went for short drive back ...

Jaguar engine cuts 3000 rpm Questions & Answers - Fixya

www.fixya.com > Forum > Tags > engine cuts 3000 rpm
1998 Jaguar XJ8 won't rev over 3000 rpm ... engine cuts out and shudders at 3000 rpm won't accelerateobd code p0332 2002 jaguar x type 3.0 l P0332 - Knock ... Car is boging out in park and will not go over ... driving, don't worry about it.

Rev Won't go up

www.jaguarforum.com/showthread.php?t=14662

Dec 15, 2015 | Jaguar Cars & Trucks

1 Answer

How to fit an upgrade armrest on an x type jag?


The center arm rest is attached to the console by 2 small Hex cap screws. The arm rest and intermediate slide panel are attached to the same hinge assembly with rivets.
to replace the upper arm rest, 1st remove the assembly from the console by removing the 2 hex screws this will allow you to work outside of the vehicle on a work bench. 3 rivets hold the arm rest to the hinge. You will need to drill out the rivets using a 1/8" drill bit. and install the replacement arm rest using new 1/8" pop rivets.
see illustration

section-ai1d4ga3barerea5mewg0gzj-4-0.jpg

Feb 07, 2015 | Jaguar X-Type Cars & Trucks

1 Answer

How do i remove the centre console on a ford focus c-max


Remove the twi phllips screws under the cup holders. Remove the cover in back of the arm rest. Remove the two phillips screw. Remove the cap covering the last screw in the back of the console. Remove last phillips screw. pull up parking brake,remove console. Good luck.

Nov 12, 2009 | 2000 Ford Focus

2 Answers

2001 XJ8 keyless remote programming


This is the procedure from the service manaul:

JAGUAR
XJ8 Remote Control Programming
1. Unlock the Boot/trunk with key.
2. Turn Ignition on.
3. Warning light on dash comes on.
4. When they go out, lift arm rest, inside their is a valley button, Press 5 times within 5 secs of lights on dash going out, Horn & Lights Flash.
5. Press any button on remote, remote programmed.

Jan 16, 2009 | 2006 Jaguar XJ8

1 Answer

Keyless entry not working


Try re-programming the remotes, here is the procedure for your car.
JAGUAR
XJ8 Remote Control Programming
1. Unlock the trunk with key.
2. Turn Ignition on.
3. Warning light on dash comes on.
4. When they go out, lift arm rest, inside their is a valley button, Press 5 times within 5 secs of lights on dash going out, Horn & Lights Flash.
5. Press any button on remote, remote programmed

Dec 11, 2008 | 2006 Jaguar XJ8

1 Answer

Xj8 2000


they are pressed in, Jaguar uses a special tool which fits over the bushing and you have to use a press to remove them, sometimes they are so tight they need to be burped out with an air hammer.
Not a job I would tackle myself as you need to strip down the suspension to get the arm off for replacement.

Oct 05, 2008 | 1995 Jaguar XJ6

Not finding what you are looking for?
2001 Jaguar XJ8 Logo

Related Topics:

258 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22082 Answers

yadayada
yadayada

Level 3 Expert

74192 Answers

SPEEDY CAR WORK SHOP...

Level 2 Expert

447 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...