Question about 2000 Chevrolet Venture

1 Answer

Brakes How do you trouble shoot abs brakes?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 341 Answers

You need a code reader to fine out whats wrong and which part is bad.take it to autozone they will check for free..

Posted on Dec 06, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Trouble shooting abs motor,#58900.


You will need to get the fault codes read as the lights come on for any of the following low brake fluid ,sensor or wiring fault ,low pressure in system faulty computer abs
Also the abs pump runs at a couple of hundred psi and fiddling around is not recommended and bleeding the system after a good fiddle takes a while
I gave up bleeding the system after 6 hrs over 2 days
I was a bit miffed in the end (swearing removed to post )

Oct 11, 2016 | 2009 Kia Sportage

1 Answer

2006 Buick Rendezvous 10 Amp ABS fuse keeps blowing. What could be the problem?


There is a shot to ground in the ABS system ! If familiar with electrical trouble shoot , find a wiring diagram an test the B+ power circuit ! That fuse supply's power to the electronic brake control module , if no short on wire from fuse box to brake control module , the module has an internal problem .

Jul 26, 2016 | 2006 Buick Rendezvous

1 Answer

No brake fluid going through abs system module


Use a professional scan tool to command
the abs hcu unit open & try bleeding

Mar 12, 2013 | Cars & Trucks

1 Answer

Abs & TCS-off dash lights both stay on. Pushing the TCS off switch does not help. "seem" to stop fine. Emergency brake seems to be fully off, not dragging. My wife encountered a patch of ice...


Hello: If there is a problem in the ABS it will bring on the tcs light as well. To determine what is causing the problem you need to have the ABS checked with a scanner to get the code. Then trouble shoot the components that the code leads you to. Normal braking is available with the light on but TCS is not as it relies on ABS for functioning the TCS.

Mar 04, 2011 | 2008 Saturn VUE

1 Answer

How to trouble shoot the brake system?


To trouble shoot the brake system you have to check:AntiLock Brake System ABS:
Hydraulic Modulator
Basically this unit holds steady or bleeds off pressure in brake line, as necessary, when the Electronic Brake Control Module (EBCM) detects an abnormal deceleration in the speed of the wheel. On 2000 and later models the EBCM and Brake Pressure Modulator Valve (BPMV) are mounted on a bracket attached on the left strut tower.
Wheel Speed Sensors, brake fluid level, brake hoses and lines, inspect and replacement, Brake hydraulic system-bleeding, Brake light switch, check, adjustment and replacement.
Disk brake caliper, disk brake pads, drum brake shoes, master cylinder, master cylinder reservoir, O-rings replacement, parking brake adjustment, parking brake cables inspect and replacement, parking brake shoes-replacement, power brake booster, check or replacement, wheel cylinder inspect and replace.

Oct 10, 2010 | 2000 Chevrolet Venture

1 Answer

Brakes popping when applied


SOUND LIKE PROBLEM IN THE ABS BRAKE SYSTEM AND TRAC SYSTEM.TAKE VECHICLE TO DEALERSHIP.THEY HAVE TO USE A TECH SCANNER TO TROUBLE SHOOT AND FIX PROBLEM.

Jun 28, 2010 | 2004 Chevrolet TrailBlazer

1 Answer

I have a 2000 VW bettle tonight the check engine light, EPC Light, Brake light its Flashing< and the ABS light came on. What could be causing this Problem.


HAVE DEALERSHIP SCAN IT THEY HAVE SPECIAL SCANNER FOR TROUBLE SHOOTING ABS BRAKES SYSTEM.AND THE CHECK ENGINE LIGHT.THIS NOT HOME FIX.

Sep 30, 2009 | 2000 Volkswagen Beetle

1 Answer

BRAKE PEDAL GOES ALMOST TO THE FLOOR, DASH LIGHT ON FOR BRAKES, PEDAL APPEARS SPONGEY.


SOUND LIKE AIR IN BRAKE LINES.CHECK BRAKE FLUID LEVEL MAKE SURE ITS NOT LOW. CHECK ALL BRAKE HOSES AND BRAKE LINES. FOR LEAKS. YOU HAVE TO BLEED BRAKES.IF ALL IS GOOD.YOU HAVE MASTER CYLINDER AND ABS BRAKE FAILURE.HAVE DEALERSHIP FIX IT.THEY HAVE THE EQUIPMENT TO TROUBLE SHOOT AND BLEED THE BRAKE SYSTEM.

Sep 12, 2009 | 1995 Dodge Grand Caravan

1 Answer

ABS lamp comes on 1995 Dodge Caravan


your abs sensor would be 1st place to look then brake pads and calipers

May 20, 2009 | 1988 Chevrolet K2500

Not finding what you are looking for?
2000 Chevrolet Venture Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...