Question about 1991 Toyota Pickup

1 Answer

Reverse lights and license plate light dont work

I have a custom bumper with new license plate light and reverse lights on original truck that dont work i have checked wiring and fuses a wiring diagram would be helpful

Posted by on

  • Anonymous Mar 30, 2014

    Going to mount on bumper

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 6,674 Answers

Try link below, may point you in right direction, but you'll have to scroll down & find what you need. Otherwise I'd start from bumper with test light & work my way back toward front harness, after all fuses, plugs etc been checked.

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c152800610de

Posted on Dec 12, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Running lights for 2005 odyssey on license plate are not working


The lenses cover & the lenses housing snap in to place. There are plastic tabs on the sides of each.
Directions: Remove the license plate light housing, and disconnect the 2P connector from the light. Remove the lens from the light, and then replace the bulb. Install the light in the reverse order of removal.

Nov 05, 2012 | Cars & Trucks

1 Answer

License plate light and reverse lights dont work after checking lights and fuse


They are two different circuits. Do you have voltage at the neutral safety switch when in reverse ? Are the ground wires for the light sockets ok ?

Aug 05, 2012 | 2001 Buick Century

2 Answers

Where is reverse light and license plate light fusee located. how do i change reverse light


The back up lights is fuse S14, starting with 1 on the left of the fuseblock.
License light is on fuse S3.
Both are supposed to be 10 amp.

Mar 07, 2011 | 2000 Volkswagen Beetle

1 Answer

Do I have to remove the tray liner from the 2003 Rodeo pick up to replace tail light assembly?


Utility And Sportside Pick-Up Models
  1. Make sure the headlight switch is off and the ignition switch is in the lock position.

  2. Unfasten the screws retaining the lens, then remove the lens.

  3. Disconnect the bulb socket from the license plate lamp by rotating it 1/4 of a turn counterclockwise.

  4. Remove the bulb from the socket.

  5. Installation is the reverse of removal.
    Without A Step Bumper

    1. Make sure the headlight switch is off and the ignition switch is in the lock position.

    2. Disconnect the bulb socket from the license plate lamp by rotating it 1/4 of a turn counterclockwise.

    3. Pull the bulb from the socket.

    4. If necessary, remove the lens retaining clip and the lens from the filler panel.

    5. Installation is the reverse of removal.
      With A Step Bumper

      1. Make sure the headlight switch is off and the ignition switch is in the lock position.

      2. If necessary, lift the lamp up and tilt the bottom away from the bumper to release the lamp retainer.

      3. Disconnect the bulb socket from the license plate lamp by rotating it 1/4 of a turn counterclockwise.

      4. Pull the bulb from the socket.

      5. If necessary, remove the step bumper pad, the screws that attach the lamp to the bumper and remove the lamp assembly.

      6. Installation is the reverse of removal. Tighten the lamp assembly-to-bumper screws to 14 inch lbs. (1.6 Nm).

Dec 12, 2010 | Isuzu Pickup Cars & Trucks

1 Answer

How do you replace the license plate light on a k1500 1995 gmc truck


All you have to do is reach up underneath the rear bumper, grab the light socket and turn a quarter turn counter-clock wise and pull the socket out of the housing. Then firmly grab the light bulb and pull straight out. Just reverse these directions for replacement.

May 31, 2010 | 1995 GMC Sierra

1 Answer

License plate bulb needs replacing


Remove license plate. Unscrew the screws on the underside of the bumper. Slide the lights back toward the trunk and then down through the opening. Unscrew bulb and replace with a new one.

Reverse steps to reinstall the lights.

Feb 06, 2010 | 2003 Chevrolet Impala

1 Answer

Back up lights and license plate light doesn't work.


Reverse lights are activated by a small switch on the transmission. Usually located on the passenger side of the vehicle with a small rubber cap over the switch, Your plate light bulbs are probably in need of replacement, and have nothing to do with the reverse lights.

Jan 17, 2010 | 1996 Jeep Grand Cherokee

1 Answer

Need to replace license plate lights on 95 ford explorer. can't reach underneath the bumper. does the plastic assembly just twist off?


  1. From underneath the rear of the vehicle, grasp the lamp socket and rotate it 1/4 turn.
  2. Pull the lamp socket from the lens.
  3. Pull the bulb from the socket
  4. Installation is the reverse of the removal procedure.

3761db9.gif
Exploded view of the rear license plate light assembly-step bumper shown, other styles are similar

Oct 20, 2009 | 1995 Ford Explorer

1 Answer

License plate light hookup


Hi,you should have the original licence plate light wires, if these are a different colour from the ones on the new bumper you will have to splice the originals to the new ones use a test lamp/meter to test for the live feed and connect this to the red wires then connect the black wires and join these either to a good earth point or the other wire which should be ground.

Feb 01, 2009 | 1990 Toyota Pickup

Not finding what you are looking for?
1991 Toyota Pickup Logo

399 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

63990 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...