Question about 1999 Mercury Villager
Where is it located
Hi..The Blower Motor Resistor is located under the glove compartment, pass side. You do not need to remove the glove box, or anything. Look under the dash on the pass side and you will see the resistor with the wires leading to it. (looks about the width of a Credit card) Simply undo the ( 2 ) 9 or 10mm screws from the resistor, slide/pull it down from the slot, un-clip the wire harness and replace with the new resistor. Screw it back up. Thats it. Takes about 4 minutes. The dealer wants $125.+ to do the job. The resistor is about $24.00.
Good Luck. If it keeps blowing, the blower motor is probably drawing too many amps. Then you have to switch that out.
Posted on Dec 29, 2008
The low speed resistor on a 1999 Merc Villager is under the dash, passenger side, almost behind the glovebox. 1 set of wires going to it....2 small screws hold it in. once out it looks like a circuit board slightly larger than a credit card. I've changed mine 4 times. I now assume there is a short somewhere else in the system. Now my high speed blower resistor, or whatever has crapped out and I have no blow in any speed. Lovely for the middle of winter, eh??:
Posted on Jan 12, 2014
For the rear blower resistor on a 1998 Mercury Villager, it is really simple, pop off the grill on the side wall of the van underneath the blower controls and upper air outlets (about 12" by 14") look for the resistor that is held in place by two screws, one at each end, and a wire in the middle. Remove two screws after disconnecting wire and remove resistor. Reverse order to install. Buy part before you start. If the fan doesn't work or it is on one speed only, it is probably the blower motor resistor. Part is available through Advance for about $30, NAPA has it for $18, takes two days for Advance, one to two weeks for NAPA. Advance will price match and not even include the $7 NAPA wants for getting it to store.
Posted on Mar 22, 2011
Check under the hood on the right side where the blower is located
Posted on Dec 06, 2008
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
the part you need to replace is the blower motor resistor assembly it has a screw on each side of it with a plug in th middle and for the most part it is on the passanger under the dash behind a black cover stop by a auto store and take a look at one and then you know what you are looking for and at the same time you can find out how much its going to cost i am only going to guess it somewhere around $15.00 to 25.00 dollars.
Posted on Feb 14, 2009
the resistor is behind your glove box. open the box and push in the sides to release it and let it hang down...the resistor is right there. I didn't try to replace it, a friend did it, but the part was under $20.
Posted on Feb 01, 2009
The blower speed controller is located under the hood on the right or passenger side on the heater housing just to the side of the heater hoses near the very back of the right cylinder head.
Yes that would cause the concern you are having.
Posted on Feb 05, 2009
depends on what year van..1996-2000,located in engine compartment just above right strut tower at firewall..2001-2007..located behind glove box
Posted on Jun 12, 2009
Tips for a great answer:
Feb 21, 2015 | 2005 Ford Mustang V6
Jan 10, 2011 | 1999 Mercury Mountaineer
Dec 18, 2010 | 1997 GMC Sierra
Dec 13, 2010 | Chevrolet S 10 Cars & Trucks
Nov 10, 2010 | 2000 Jeep Grand Cherokee
Dec 12, 2009 | 1999 Mercury Villager
May 12, 2009 | 2005 Kia Sorento
May 06, 2009 | 1999 Mercury Cougar
Jan 08, 2009 | 1994 BMW 3 Series
Dec 06, 2008 | 1999 Mercury Villager
Jul 21, 2015 | 1999 Mercury Villager
2,866 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: