Question about 1998 Toyota Sienna

1 Answer

Change ignition lock cylinder

How do i remove the ingition lock cylinder from a toyota sienna 1998?

Posted by on

  • Toyota Ed May 11, 2010

    You are going to need a Dremel "Moto-tool". Do you have one?

  • Anonymous Mar 30, 2014

    Acura 1.6 EL ,1998, the key is stuck in the lock,can't be removed. Next day the car couldn't start. Should I replace the ignition lock cylinder?

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 12 Answers

Put the lock cylinder in the acc position and with a small screwdriver depress the pin retaining the cylinder then pull it sttraight out

Posted on Dec 24, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1998 toyota sienna get misfire on No 3 spark plug.error code is P0303.


check for fuel and compression on cylinder 3. any oil on old spark plug?

Feb 27, 2017 | 1998 Toyota Sienna

4 Answers

I have a 2000 toyota corolla and the key will only turn to acc. We have tried the other key. The stering wheel is unlocked. We have jiggled the shifter to make sure it is in park.


See if you turn the wheel and try to turn the key at the same time if it releases. We might get a free spot where the key should turn. The lock may be in a bind and pressure on it may release it.
Clean and lubricate the lock cylinder. Electric cleaner to flush the dirt and liquid graphite to lubricate. A substitute for the electric cleaner is a spray of isoprophyl alcohol.
You may also need to tap the assembly for the ignition switch to release the mechanical parts. See if you can get the cover of the steering column off to gain access to the ignition switch assembly.
Check also if the spare does the same, other wise the key may have deformed.

May 02, 2011 | Toyota Corolla Cars & Trucks

1 Answer

1998 toyota sienna. code says "cylinder #3 misfire". How do I fix it?


It appears that you have a bad spark plug. You may want to get a new set of plugs, and possibly wires if they haven't been changed in a while.

Rather you, or someone else changes the plugs, try to make a mental note to look at the plug in the #3 cylinder when it is removed, just to make sure it doesn't have oil on it, that would raise other issues. Hopefully the plug is just old and worn.

I hope this helps you.

Jan 31, 2011 | 1998 Toyota Sienna

1 Answer

I have a 1998 toyota sienna with 132,000 miles on it. Recently I noticed a "shuddering" or hesitation while driving that was intermittent at idle and driving. The check engine light came on...


my name is Jerry Tiet. Base on my experience on 1998 Toyota Sienna with the DTC P0303 show there is a misfire in cylinder #3. a possible cause is the ignition coil of the #3 cylinder. Compare the resistance value of the ignition coil of cylinder #3 with the other coil or simply switch ignition coil #3 with one of the other ignition coil and clear the DTC with the scan tool. Then run engine for couple days. If the check engine light on again. Let me know what is the DTC code.

Nov 11, 2010 | 1998 Toyota Sienna

1 Answer

Ignition key won't go past the acc position


yur key lock cylinder is defective. This is common on most 97-00 Toyotas. Have the cylinder replaced!!

Mar 15, 2010 | 1998 Toyota Sienna

1 Answer

Trying to remove ingition lock cylinder


After cover has been remove you'll see the bolts that hold the lock, when lock was install the head of the bolts are made to break off for theft reasons, get a small chisel and hit the bolt as to loosen it, once it breaks loose they'll come off easy, when installing new lock keep turning bolt till the head of the small bolt breaks off, it made to do that.

Jan 05, 2010 | 1998 Toyota Camry

1 Answer

I want to replace ignition lock cylinder on my 1998 Toyota 4Runner do I need special tools to do it? or what are the steps to do it? thanks.


You have to remove the plastic cover underneath of the steering wheel, after that the metal shield behind the plastic cover. When you remove the shield you will get access to the ignition lock cylinder. Disconnect the wire harness, remove the cylinder, install a new cylinder. Connect the wire harness, install the shield, install the plastic cover.

PS: Before start write down the code for your stereo (if you have one), disconnect the negative cable from the battery. Be careful when you work around the air bags.

Sep 17, 2009 | 1998 Toyota 4Runner

3 Answers

1998 toyota


There is a pin that you have to push in on the bottom of the lock cylinder housing.It is recessed in a hole.You have to turn the key to acc or on to get it to push in.Once you push it in you can pull the key and lock cylinder out.

Dec 01, 2008 | 1998 Toyota Camry

Not finding what you are looking for?
1998 Toyota Sienna Logo

375 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

70346 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6869 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...