Question about 2006 GMC Envoy

1 Answer

Can't locate Intake Air Temperature Sensor Connector

Need help finding Intake Air Temperature Sensor Connector on my 2006 GMC Envoy 4.2 L. How many wires and what color to connector? Was told two, but cannot find a two wire connector near air intake. Please be detailed in response.

Thank you in advance for your help.

Posted by on

  • 4 more comments 
  • Anonymous Mar 27, 2009

    the diagram is too small

  • Anonymous Mar 14, 2014

    location intake air temperature sensor

  • Anonymous Mar 27, 2014

    I need a picture of the intake air temperature sensor

  • Anonymous Mar 27, 2014

    I need a picture of the intake air temperature sensor on a 2000 mercury sable

  • Anonymous Mar 28, 2014

    where is the intake air temperature (TA) sensor on a 1992 acura legend v6 3.2 liter plug in at? not the one in front of the engine but behind it on the passenger side near the intake manifold.

  • Anonymous Mar 30, 2014

    air temp control blend door location

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 37 Answers

The IAT is integrated with the MAF (Mass Air Flow) sensor all one unit the following diagram should help
Can't locate Intake Air Temperature Sensor Connect - 9b5bca8.jpg

Posted on Dec 06, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is iat sensor located on 2006 tpyota tacoma 4,ol ?


Intake Air Temperature (IAT) sensor and Manifold Absolute Pressure (MAP) sensor are combined into a single assembly which is called Mass Air Flow (MAF) sensor. This MAF sensor is located on the air filter box near air filter hose, and is connected with a five wire connector. You cannot replace the IAT sensor alone. Instead a MAF sensor is replaced altogether.

25646166-ts5vql1j3jwqenesgxdwpnsg-5-0.png



25646166-ts5vql1j3jwqenesgxdwpnsg-5-2.png
Thank you for visiting Fixya.

Apr 14, 2015 | 2006 Toyota Tacoma

1 Answer

What does p0113 mean on dodge durango 2002, and how to solve it?


Fault Code Definition
  • Intake Air Temperature Circuit High Input
What does this mean?
The Intake Air Temperature Sensor measures the rise and fall of the air temperature inside the Intake Manifold. This provides critical data needed for the Powertrain Control Module (PCM) to control the Air Fuel Ratio, the Ignition Spark Timing and many components of the Emission Control Systems.
Code P0113 sets when the voltage signal to the PCM from the Intake Air Temperature Sensor Circuit stays above 4.5 volts while the Coolant Temperature Voltage readings are rising and falling within an appropriate range.
Symptoms
  • Check Engine Light will illuminate
  • In some cases, the engine may be hard starting and/or get poor fuel economy
  • Poor engine performance/hesitation on acceleration
Common Problems That Trigger the P0113 Code
  • Defective Intake Air Temperature Sensor
  • Dirty air filter
  • Defective Mass Air Flow Sensor
  • Faulty or corroded Intake Air Temperature Sensor wiring or connections
Common Misdiagnoses
  • Intake Air Temperature Sensor is replaced when the real cause is a dirty air filter
  • Intake Air Temperature Sensor is replaced when the real cause is a poor connection or chafed wiring
  • Intake Air Temperature Sensor is replaced when the real problem is in the Mass Air Flow Sensor
  • P0113 Diagnostic Theory for Shops and Technicians
  • When diagnosing a P0113 code, it is important to record the freeze frame information and then to duplicate the code setting conditions with a test drive while paying close attention to engine load, throttle position, RPM, and road speed on a data streaming scan tool. As you drive the vehicle, compare these values to the Intake Air Temperature Sensor PID or parameter ID. The Intake Air Temperature Sensor voltage values should rise and fall with changes in engine temperature. Compare the Intake Air Temperature or IAT readings to the Coolant Temperature Sensor readings, as they should move in tandem with each other. However, the Engine Coolant Temperature sensor will have a much higher temperature range.
    Check the IAT sensor connector with the key on and the engine off. There needs to be a steady 5 volt reference voltage and a very good ground. Find and use the proper engine performance wiring diagram to discern the proper color and position of these wires in the connector.
    It never hurts to do a key on-engine off voltage output test of the IAT sensor. Typically, I CAREFULLY use a heat gun to raise the temperature of the area around the sensor and study the change in values of the Intake Air Temperature. It's important to use the scan tool data stream as this will verify the IAT harness and connections.

Mar 31, 2014 | 2001 Dodge Durango

1 Answer

2002 isuzu rodeo cylinder head torque lbs. for 2.2


Print


Removal & Installation

2.2L Engine

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Drain the cooling system.
  3. Relieve the fuel system pressure.
  4. Remove or disconnect the following: Negative battery cableIntake Air Temperature (IAT) sensor connectorPositive Crankcase Ventilation (PCV) valve and hoseAir intake assemblyUpper radiator hoseAccessory drive beltExhaust front pipeAlternator and bracketsCrankshaft Position (CKP) sensor connectorKnock sensor connectorHeater hosesWater bypass hoseFuel linesEvaporative Emissions (EVAP) valve connectorCanister hoseIntake manifoldEngine wiring harness connectors at left rear of the engine compartmentPower steering pump pressure switch connectorFront coverSpark plugs and wiresCamshaft Position (CMP) sensorValve coverTiming belt. Refer to the Timing Belt unit repair section.Timing belt idler pulleysTiming belt rear coverOil pressure switch connectorCamshaftsCylinder head. Remove the bolts in reverse of the tightening sequence.

    Negative battery cable Intake Air Temperature (IAT) sensor connector Positive Crankcase Ventilation (PCV) valve and hose Air intake assembly Upper radiator hose Accessory drive belt Exhaust front pipe Alternator and brackets Crankshaft Position (CKP) sensor connector Knock sensor connector Heater hoses Water bypass hose Fuel lines Evaporative Emissions (EVAP) valve connector Canister hose Intake manifold Engine wiring harness connectors at left rear of the engine compartment Power steering pump pressure switch connector Front cover Spark plugs and wires Camshaft Position (CMP) sensor Valve cover Timing belt. Refer to the Timing Belt unit repair section. Timing belt idler pulleys Timing belt rear cover Oil pressure switch connector Camshafts Cylinder head. Remove the bolts in reverse of the tightening sequence.

To install:


0996b43f802097a8.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Cylinder head torque sequence-2.2L (VIN D) engine

NOTE Use new cylinder head bolts for assembly.

  1. Install the cylinder head with a new gasket. Tighten the bolts in sequence as follows: Step 1: 18 ft. lbs. (25 Nm)Step 2: Plus 90 degreesStep 3: Plus 90 degreesStep 4: Plus 90 degrees
    1. Step 1: 18 ft. lbs. (25 Nm)
    2. Step 2: Plus 90 degrees
    3. Step 3: Plus 90 degrees
    4. Step 4: Plus 90 degrees

  2. Install or connect the following: CamshaftsOil pressure switch connectorTiming belt rear coverTiming belt idler pulleys. Tighten the bolts to 18 ft. lbs. (25 Nm).Timing beltValve coverCMP sensorSpark plugs and wiresFront coverPower steering pump pressure switch connectorEngine wiring harness connectors at left rear of the engine compartmentIntake manifoldCanister hoseEVAP valve connectorFuel linesWater bypass hoseHeater hosesKnock sensor connectorCKP sensor connectorAlternator and bracketsExhaust front pipeAccessory drive beltUpper radiator hoseAir intake assemblyPCV valve and hoseIAT sensor connectorNegative battery cable

    Camshafts Oil pressure switch connector Timing belt rear cover Timing belt idler pulleys. Tighten the bolts to 18 ft. lbs. (25 Nm). Timing belt Valve cover CMP sensor Spark plugs and wires Front cover Power steering pump pressure switch connector Engine wiring harness connectors at left rear of the engine compartment Intake manifold Canister hose EVAP valve connector Fuel lines Water bypass hose Heater hoses Knock sensor connector CKP sensor connector Alternator and brackets Exhaust front pipe Accessory drive belt Upper radiator hose Air intake assembly PCV valve and hose IAT sensor connector Negative battery cable
  3. Fill the cooling system.
  4. Start the engine and check for leaks.

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the cooling system.
  3. Relieve the fuel system pressure.
  4. Remove or disconnect the following:

    Negative battery cable Intake Air Temperature (IAT) sensor connector Positive Crankcase Ventilation (PCV) valve and hose Air intake assembly Upper radiator hose Accessory drive belt Exhaust front pipe Alternator and brackets Crankshaft Position (CKP) sensor connector Knock sensor connector Heater hoses Water bypass hose Fuel lines Evaporative Emissions (EVAP) valve connector Canister hose Intake manifold Engine wiring harness connectors at left rear of the engine compartment Power steering pump pressure switch connector Front cover Spark plugs and wires Camshaft Position (CMP) sensor Valve cover Timing belt. Refer to the Timing Belt procedure. Timing belt idler pulleys Timing belt rear cover Oil pressure switch connector Camshafts Cylinder head. Remove the bolts in reverse of the tightening sequence.

To install:

0996b43f802097a8.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Cylinder head torque sequence-2.2L (VIN D) engine


NOTE Use new cylinder head bolts for assembly.

  1. Install the cylinder head with a new gasket. Tighten the bolts in sequence as follows:
    1. Step 1: 18 ft. lbs. (25 Nm)
    2. Step 2: Plus 90 degrees
    3. Step 3: Plus 90 degrees
    4. Step 4: Plus 90 degrees

  2. Install or connect the following:

    Camshafts Oil pressure switch connector Timing belt rear cover Timing belt idler pulleys. Tighten the bolts to 18 ft. lbs. (25 Nm). Timing belt Valve cover CMP sensor Spark plugs and wires Front cover Power steering pump pressure switch connector Engine wiring harness connectors at left rear of the engine compartment Intake manifold Canister hose EVAP valve connector Fuel lines Water bypass hose Heater hoses Knock sensor connector CKP sensor connector Alternator and brackets Exhaust front pipe Accessory drive belt Upper radiator hose Air intake assembly PCV valve and hose IAT sensor connector Negative battery cable
  3. Fill the cooling system.
  4. Start the engine and check for leaks.

May 26, 2012 | Isuzu Rodeo Cars & Trucks

1 Answer

My outdoor temperature indicator is stuck on 0C° GMC Envoy SLE 2006


The temperature sensor is defective, it is located just in front of the radiator, under the radiator support. Before replacing, make sure the electrical connector is seated properly.

Sep 11, 2010 | 2006 GMC Envoy

1 Answer

Intake air temperature sensor location on gmc envoy?


The intake air temp sensor is located in the induction tube between the air filter box and the throttle body.

Jul 13, 2010 | 2003 GMC Envoy

1 Answer

Trouble locating cooling sensor on 2003 gmc envoy


4.2L Engine To Remove:
  1. Disconnect the negative battery cable from the battery.
  2. Drain the coolant from the engine.
  3. Disconnect the engine coolant temperature (ECT) sensor connector. Engine coolant temperature sensor removal and installation gm-04-42-1509.gif

  4. Remove the engine coolant temperature (ECT) sensor from the engine.
To Install:
  1. Apply thread sealer P/N 12346004 or equivalent to the engine coolant temperature (ECT) sensor threads.
  2. Install the engine coolant temperature (ECT) sensor into the engine. Torque the sensor to 12 ft-lb (16 Nm).
  3. Connect the engine coolant temperature (ECT) sensor connector.
  4. Refill the engine with coolant.
  5. Connect the negative battery cable to the battery.
5.3L & 6.0L Engines To Remove:
  1. Drain the coolant from the engine.
  2. Disconnect the engine coolant temperature (ECT) sensor connector. Engine coolant temperature sensor removal and installation removeect.gif

  3. Remove the engine coolant temperature (ECT) sensor from the left cylinder head.
To Install:
  1. Apply thread sealer P/N 12346004 or equivalent to the engine coolant temperature (ECT) sensor threads.
  2. Install the engine coolant temperature (ECT) sensor into the left cylinder head. Torque the sensor to 15 ft-lb (20 Nm).
  3. Connect the engine coolant temperature (ECT) sensor connector.
  4. Refill the engine with coolant.

Jul 08, 2010 | 2003 GMC Envoy

1 Answer

I got a p0113 code for the mass air flow sensor on a ford sport track 2001 4.0 litre. I replaced the part but my truck will not run with the sensor plugged in. I can start it with it unplugged but when I...


1. At the Mass Air Flow (MAF) sensor connector, backprobe the Gray (GY) wire at terminal #6 with the key on and the MAF sensor connected. Typical voltage will be about 2-3.5v depending on temperature.

2. If the voltage is above 4.5v (which is what the code P0113 indicates) check the voltage on the Gray/Red (GY/RD) wire at terminal #1 of the MAF sensor connector. The voltage on the GY/RD should be less than about 0.1v.

3. If the GY/RD wire shows less than 0.1v and the voltage on the GY wire is above 4.5v, inspect the connections at the MAF sensor connector. If OK, replace the MAF sensor for the open Intake Air Temperature (IAT) Sensor.

4. If the voltage on the GY/RD wire shows above 0.1v, locate and repair the high resistance between the MAF sensor and pin #91 of the Powertrain Control Module (PCM) connector.

5. If the voltage on the GY wire is not above 4.5v but the scanner shows -40 F on the data stream, check the voltage at pin 39 of the PCM. If the voltage at the PCM is above 4.5v, locate and repair the high resistance or open circuit in the GY wire between the PCM and MAF sensor connector

Nov 23, 2009 | 2001 Ford Explorer Sport Trac

1 Answer

1998 cavalier intake air temperature error


Traced wires with multimeter. Found gray wire broken at sensor connector. Repaired connector wire and now have correct voltage and temperature readings.

Jun 20, 2009 | 2005 Jeep Liberty

1 Answer

2004 330i sedan can't find lacation to replace intake air temperature sensor


5047e99.png
B6205 Intake air temperature sensor X6205 Component connector (2-pin, black), Intake air temperature sensor
To access this part of the intake manifold, you will nedd to remove the cosmetic covers on teh top of the engine. there are a total of 4 screws, all 10 mm, that need to be removed, under teh round caps in the cover.

Feb 18, 2009 | 1994 BMW 3 Series

1 Answer

4 cylinder motor


http://www.analogstereo.com/pdf/om/hyundai_tiburon_owners_manual_2003.pdf
note_icon.gif Mark all wiring and hoses to avoid misconnection. Inspection the timing belt before removing the cylinder head. Turn the crankshaft pulley so that the No. 1 piston is at top dead center
1. Disconnect the neagative terminal from the battery 2. Remove the engine cover. . Drain the engine coolant. Remove the radiator cap to speed draining. 4. Remove the intake air hose and air cleaner assembly. (1) Disconnect the AFS connector. (2) Disconnect the breather hose from air cleaner hose. (3) Remove the intake air hose and air cleaner. 5. Remove the upper radiator hose (A) and lower radiator hose (B). 6. Remove the heater hoses 7. Remove the engine wire harness connectors and wire harness clamps from the cylinder head and the intake manifold. (1) OCV(Oil Control Valve) connector (A). (2) Oil temperature sensor connector (B). (3) ECT (Engine Coolant Temperature) sensor (C) connector. (4) Ignition coil connector (D). (5) TPS (Throttle Position Sensor) connector (A). (6) ISA (Idle Speed Actuator) connector (B). (7) CMP (Camshaft Position Sensor) connector (A). (8) Four fuel injector connectors (B). (9) Knock sensor connector (C).

May 27, 2008 | 2003 Hyundai Tiburon

Not finding what you are looking for?
2006 GMC Envoy Logo

2,293 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

70374 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...