Question about 2006 Peugeot 604

2 Answers

All doors will not lock - 2006 Peugeot 604

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have trouble opening the door locks on my peugeot expert

Posted on May 08, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Look under the back seat there might be a connection problem...

Posted on Jul 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 Buick Rendezvous you can hear the relay clicking but the door locks will not open and close


Check for broke wires inside the boot from body to driver door , this is a common problem . If you don't find broke wire's , pull the door panel to get at driver door switch . Check for voltage an ground circuit .
Rendezvous Door Lock System Components
The power door lock system consists of the following components:
?€¢
Body control module (BCM)


?€¢
Driver door lock switch


?€¢
Front passenger door lock switch


?€¢
Door lock actuators in each of the doors


?€¢
Door lock system fuse into the BCM (BCM D 25A fuse)


Door Lock Operation
When the BCM detects a transition of either of the door lock switches to the LOCK position, it switches the door lock actuator lock control circuit to voltage. Since the lock actuator unlock control circuits are at ground potential within the BCM, the door lock actuator motors transition to the Lock position.
Driver Door Unlock Operation
When the BCM detects a transition of either of the door lock switches to the UNLOCK position, it switches the driver door lock actuator unlock control circuit to voltage. Since the door lock actuator lock control circuit is at ground potential within the BCM, the LF door lock actuator motor transitions to the Unlock position.
The driver door lock actuator unlock control circuit is a dedicated control circuit used only for the driver door lock actuator motor. This is done so that the driver door may be unlocked by itself using a keyless entry transmitter or an automatic door unlock function (if programmed).
Passenger Door Unlock Operation
When the BCM detects a transition of either of the door lock switches to the UNLOCK position, it switches the door lock actuator unlock control circuits to voltage. Since the door lock actuator lock control circuit is at ground potential within the BCM, the passenger door lock actuator motors transition to the Unlock position.
The door lock actuator unlock control circuits are dedicated control circuits used only for the passenger door lock actuator motors. This is done so that the driver door may be unlocked seperate from the passenger doors using a keyless entry transmitter or an automatic door unlock function (if programmed). This video on testing computer controlled door locks on a Subaru , doesn't matter . test yours same way > The BCM controls your door locks .
Are all of the power door locks inoperative from both door lock switches?

Oct 12, 2016 | 2005 Buick Rendezvous

1 Answer

2002 Cadi Deville, can't get any locks to operate with remote or dash push buttons, the remote operates everthing but the locks! When the remote door lock is pressed, lites flash,horn blows locks not.


Power Door Lock Operation
The vehicle is equipped with power door locks. Each lock actuator is powered and controlled by the door module mounted in the individual door, but the rear integration module (RIM), which is the master control for the door lock system, determines when the lock functions are permitted. The RIM receives and examines the requested lock function from the individual door modules, or from the remote function actuator (RFA) via the class 2 serial data circuit. The RIM also examines the transmission shift selector position and the ignition switch position information available over the Class 2 serial data circuits. If the RIM determines that a lock or unlock function is permitted, it sends a class 2 message back to the individual door modules commanding them to perform that Lock or Unlock function.
Power Door Lock Components
The power door lock system consists of the following components:
?€¢
Driver door lock switch


?€¢
Passenger front door lock switch


?€¢
LH rear door lock switch


?€¢
RH rear door lock switch


?€¢
LH middle door lock switch (w/ V4U)


?€¢
RH middle door lock switch (w/ V4U)


?€¢
Driver door switch assembly (DDSA)


?€¢
Driver door module (DDM)


?€¢
Passenger front door module (PDM)


?€¢
LH rear door module (LRDM)


?€¢
RH rear door module (RRDM)


?€¢
Left middle door module (LMDM) (w/ V4U)


?€¢
Right middle door module (RMDM) (w/ V4U)


?€¢
Driver door lock actuator


?€¢
Passenger front door lock actuator


?€¢
LH rear door lock actuator


?€¢
RH rear door lock actuator


?€¢
LH middle door lock actuator (w/V4U)


?€¢
RH middle door lock actuator (w/ V4U)


?€¢
Driver door cylinder unlock switch


?€¢
Rear integration module (RIM)


?€¢
DRVMDL fuse (10-amp)


?€¢
PASS MDL fuse (10-amp)


?€¢
RRDR MDL fuse (10-amp)


?€¢
Class 2 serial data link

Sep 27, 2016 | 2002 Cadillac Deville

1 Answer

Driver side door will not lock/unlock with the remote, but the other doors will.


no you needs a new lock actuator on that door its about $90 installed,
all the locks are on same circuit . sorry about the bad news :(

May 01, 2016 | 2003 Hyundai Sonata

1 Answer

Holden captiva rear door handle broken with child lock on..?


If door is in jammed state, open door by
repeatedly pressing the unlock button, while jiggle the inner or outer door handle this will help free up the
internal gears in the actuator that are jammed.
once the door is open.
Replace the door lock actuator with a revised
part;
Part No.: Description Qty:
96872800 LOCK,LHF DOOR (SX, CX, LX) 1
96872801 LOCK,RHF DOOR (SX, CX, LX) 1
96872811 LOCK,LHR DOOR (SX, CX, LX) 1
96872812 LOCK,RHR DOOR (SX, CX, LX) 1
96872803 LOCK,LHF DOOR (MAXX) 1
96872804 LOCK,RHF DOOR (MAXX) 1
96872813 LOCK,LHR DOOR (MAXX) 1
96872814 LOCK,RHR DOOR (MAXX) 1

Vehicle Torque Spec for door lock actuator
Captiva SX,CX, LX 10 Nm
Captiva MaXX 8 Nm

Apr 13, 2016 | Holden Cars & Trucks

1 Answer

Why does my 2004 Chevy Silverado lock and unlock while in drive? When turned off and no keys in ignition the drivers door will unlock on its own a short time later.


Gremlins ! HA HA HA sorry ! First off a little bit on how they work an what all is involved in making them work ! There are a few control modules in the mix , switches ,relays etc...
Door Lock System Components
The power door lock system consists of the following components:
?€¢
The driver door module (DDM)

?€¢
The passenger door module (PDM)

?€¢
The body control module (BCM)

?€¢
The driver information center (DIC)

?€¢
The rear door lock switch

?€¢
The door lock relay

?€¢
The door unlock relay

?€¢
The liftgate lock relay--utility vehicles with liftgate only

?€¢
The reversible door lock actuators in each of the doors and liftgate

?€¢
LOCKS 20A fuse (rear lock/unlock relay supply voltage)

?€¢
ECC 10A fuse (liftgate lock relay supply voltage)

Door Lock System Controls
The power door lock system can be controlled by any of the following:
?€¢
A power door lock or unlock switch activation

?€¢
A keyless entry transmission

?€¢
An automatic door lock function

?€¢
A delay lock function

?€¢
Door lock cylinder switch activation

?€¢
Lockout Prevention

?€¢
An airbag deployment

The front power door lock switches are integral components of the driver door module (DDM) and passenger door module (PDM). The switches are two position normally open rocker switches. When placed in either the lock or unlock positions, the switches provide a direct input to the DDM or PDM. The DDM or PDM monitors these inputs and sends a Class 2 message indicating a change in the switch's respective position. Modules which activate the power door lock motors receive the Class 2 message and activate the motor in the appropriate direction to lock or unlock the vehicle's doors and liftgate. The rear door lock switch provides a lock and unlock signal to the body control module (BCM). The BCM upon receipt of a lock or unlock signal will control the rear door lock relays and also send a Class 2 message to the DDM and PDM to perform the appropriate function.
The modules which activate the power lock motors are:
?€¢
The DDM (driver door lock actuator).

?€¢
The PDM (passenger front door lock actuator).

?€¢
The BCM (both rear door lock actuators and cargo door/liftgate).
The DDM and PDM are directly connected to the respective door lock actuator through the door lock motor lock and unlock circuits. Once a door lock or unlock request has been received, the module will supply battery voltage to one side of the actuator and ground the other causing the doors to lock or unlock.
The rear passenger and cargo doors differ slightly in that they use lock and unlock relays. The relays supply and coil sides receive a constant voltage through the battery voltage supply circuit. The normally closed contacts are connected to ground and the control side is connected to the BCM. Once a door lock or unlock request has been received by the BCM, the BCM will ground the control side of the appropriate relay. This energizes the relay and allows voltage to be applied to either the door lock motor lock or unlock circuits. since the other side of the door lock actuator is connected to the normally closed contacts of the opposing relay to ground, the doors lock or unlock.
The first place to start is have a factory or equivalent scan tool hooked up , one that can read BCM DTC'S - diagnostic trouble codes ! This could lead to a fix faster ! Watch these three videos !
Door Locks Go Crazy 1

Sep 16, 2015 | Cars & Trucks

1 Answer

Door lock dont always work


What door lock doesn't always work ? One or all of them . This is a complex set up for these door locks ! The switch is an input to the BCM - body control module . There is logic involved in the microprocessor , there are relays built in to the BCM ! Could have a DTC - diagnostic trouble code stored in the BCM ! Could be a bad connection at the BCM or master window switch ! A bad ground !
The power door lock system consists of the following components:
?€¢
Body control module (BCM)


?€¢
DOOR LKS fuse


?€¢
Driver door lock actuator


?€¢
Driver door lock switch


?€¢
GMLAN serial data link


?€¢
Keyless entry transmitter


?€¢
Passenger door lock actuator


?€¢
Passenger door lock switch


?€¢
Remote control door lock receiver (RCDLR)


The DR LCK fuse supplies battery voltage to the body control module (BCM) for the power door lock system. The BCM supplies and monitors a reference voltage to the driver and passenger door lock switches through the door lock switch lock/unlock signal circuit. Each door lock switch receives ground at G300 which is also the ground for the door lock and unlock relays located in the BCM. When a door lock switch is placed in the lock position, the reference voltage is switched to ground and the BCM senses 0.0 volts on the door lock/unlock signal circuit. When a door lock switch is placed in the unlock position, the reference voltage is switched to ground through a 1.5k ohm resistor that is internal to each of the door lock switches and the BCM senses approximately 2.9 volts on the door lock/unlock signal circuit. The BCM interprets what position the activated door lock switch was placed in based on the voltage drop.
The BCM, upon receipt of a lock or unlock switch signal, will switch the appropriate door lock/unlock relay coil control circuit to ground causing the appropriate door lock/unlock relay to energize. With the relay energized, voltage is applied to the door lock actuator control circuit causing the door to either lock, or unlock depending on what command was received from the power door lock switch or remote control door lock receiver (RCDLR). When a power door lock/unlock relay is not energized, the switch contacts are normally grounded through the BCM which provides ground to the appropriate door lock actuator for the lock/unlock function being performed. The power door lock/unlock functions are performed by reversing the flow of voltage through the door lock actuator control circuits. The BCM has three internal drivers for the power door lock system. Driver door unlock, passenger door unlock and all door lock. This is done to isolate the driver door lock actuator so it can be unlocked separately from the passenger door. For additional information concerning keyless entry, refer to Keyless Entry System Description and Operation.
This is one you may want to take to dealer or some other ASE certified repair shop ! To do this right you need a Tech 2 scan tool !
Ignition ON, observe the scan tool Door Lock Switch parameter while using the driver and passenger door lock switches. The parameter should change from Idle to Lock and Unlock.
?‡'
If the value does not change, refer to Door Lock Switch Malfunction.

Command the doors to LOCK and UNLOCK with the scan tool, the door lock actuators should LOCK and UNLOCK when changing between the commanded states.
?‡'
If one or more doors do not LOCK or UNLOCK, refer to Door Lock Malfunction.

Aug 12, 2015 | 2009 Pontiac Solstice Convertible

2 Answers

What causes a malfunction in power locks?


The power door locks are controlled by the BCM -body control module ! The door lock switch is an input to the BCM .
The BCM, upon receipt of a door lock switch lock or unlock signal, will switch the appropriate door lock actuator control circuits to battery positive voltage. The opposing side of the door lock actuators are connected to ground internally within the BCM through the other door lock actuator control circuit and the doors will lock or unlock appropriately.
First thing to do would be check power an ground circuits at the BCM ! Do you have any other systems not working -power windows etc...
The DR/LCK fuse supplies battery positive voltage to the I/P fuse block for the door lock system. The body control module (BCM) supplies and monitors a reference voltage to the door lock switch through the door lock switch lock/unlock signal circuit. The door lock switch also receives a constant ground source. If a door lock switch is placed in the lock position or unlock position, the reference voltage is taken directly to ground and the BCM detects the voltage drop on the signal circuit.
Should have BCM checked for stored DTC'S - diagnostic trouble codes !
Ignition ON, observe the scan tool Driver Door Lock Sw, Psgr Door Lock Sw, Driver Door Unlock Sw and Psgr Door Unlock Sw parameters while using the driver and passenger door lock switches. The parameters should change between Active and Inactive.
?‡'
If the values does not change between the commanded states, refer to Door Lock Switch Malfunction.

Command the driver door and passenger door lock actuators to LOCK and UNLOCK with the scan tool, the doors should LOCK and UNLOCK when changing between commanded states.
?‡'
If a door lock actuator does not perform the LOCK and UNLOCK functions, refer to Door Lock Malfunction


DTC B3130 00: All Door Unlock Circuit

DTC B3135 00: All Door Lock Circuit

Aug 09, 2015 | 2010 Chevrolet Impala

1 Answer

Automatic door locks delaying in locking.


It can be issue with keyfob or door locking mechanism.

Check the help link mentioned below:---

How to test Power door locks?

http://repairhelpcenter.blogspot.in/2012/02/how-to-test-power-door-locks.html

-------------

2006 Toyota Camry: Power Door Locks Not Working?

http://whatisbyme.blogspot.in/2012/05/2006-toyota-camry-power-door-locks-not.html

------------
Door locks or windows not working on car?
http://schematicsdiagram.blogspot.com/2011/07/door-locks-or-windows-not-working-on.html


-----------

All power door locks not working on Honda Accord?
http://howtobyme.blogspot.com/2011/11/all-power-door-locks-not-working-on_14.html

---------

Repairing car Door lock Actuator?
http://howtobyme.blogspot.com/2011/11/repairing-car-door-lock-actuator.html

-----------

How to Access car door panel?
http://howtobyme.blogspot.com/2011/11/how-to-access-car-door-panel.html
---------


Vehicle door panel components?
http://howtobyme.blogspot.com/2011/11/vehicle-door-panel-components.html

------------

Power door locks not working?

http://schematicsdiagram.blogspot.com/2011/12/power-door-locks-not-working.html

---------

Door locks not working on Ford Explorer?

http://technoanswers.blogspot.com/2012/01/door-locks-not-working-on-ford-explorer.html

----------
These details will help.
Thanks.

Dec 06, 2012 | 1995 Chevrolet G20

1 Answer

The doors lock automatically on my daughter's '99 Cougar. This has happened to me when I left the keys in the ignition and closed the driver's door. After AAA came and unlocked the doors, I removed the...


shorted wiring in doors or shorted door lock actuator in door. A grounding of a wire makes them lock normally. SO, any bare wire touching metal will ground it and lock the doors.

Principles of Operations
The Door Switch Lock Function When a door lock switch is moved into the lock position or a door lock cylinder is rotated to the lock position, the door lock switch grounds the lock circuit input to the central security module (CSM). The CSM then provides 12 volts to one side of the door lock actuators contained in the door latch unit and simultaneously grounds the other side of the door lock actuators. This completes the door lock actuator circuit, causing the door lock actuators to rotate a cam assembly, which then locks the doors. The 12 volts that the CSM provides to the door lock actuators are provided to both door lock actuators from a single pin on the CSM electrical connector.
The Door Switch Unlock Function When a door lock switch is moved into the unlock position, the door lock switch grounds the unlock circuit input to the CSM. The CSM then provides 12 volts to the opposite side (relative to locking the door) of the door lock actuator(s) contained in the door latch unit and simultaneously grounds the other side of the door lock actuator(s). This completes the door lock actuator circuit, causing the door lock actuator(s) to rotate a cam assembly in the opposite direction, which the unlocks the door(s). The 12 volts which the CSM provides to the door lock actuator(s) are provided to each door lock actuator from the individual pins on the CSM electrical connector.
--------------------------------------------------------
CSM Self-Test The CSM has a self-test which can be entered into by using a diagnostic tool. This self-test will monitor the following CSM door lock inputs:
  • Unlock switch (DTC B1311)
  • Lock switch (DTC B1300)
  • Exterior lock switch (DTC B1309)
  • Exterior unlock switch (DTC B1341)
Before running the self-test, the following conditions must be met:
  • The ignition switch must be in position II
  • The driver and passenger doors must be unlocked
  • The driver and passenger doors must be opened
  • The hood and liftgate must be closed
  • The set/reset switch, and liftgate release switch are not actuated
It is important to note that all of the diagnostic trouble codes (DTCs), with the exception of B1551 and B1553 can be retrieved with the self-test. DTCs B1551, and B1553 are continuous and will only be retrieved if the liftgate release is operated prior to retrieving the continuous DTCs.
Inspection and Verification
  1. NOTE: Make sure that the battery is fully charged before starting electrical diagnosis.
    NOTE: Prior to carrying out the CSM Self-Test, make sure that both the driver and passenger doors are open.
    Verify the customer concern.
  1. Visually inspect for obvious signs of mechanical and electrical damage.


Visual Inspection Chart Mechanical Electrical
  • Binding latch mechanisms
  • Binding linkage
  • Misaligned door
  • Central junction box (CJB) fuse(s)
  • Wiring harness
  • Electrical connector(s)
  • Door lock switch(es)
  • Door lock actuator(s)


Module Controlled Functions
The central security module (CSM) covers the following functions:
  • Central door locking
  • Double door locking
  • Anti - theft alarm incorporating
    • forced entry
    • radio theft
  • Radio frequency remote control of
    • central door locking
    • panic alarm
    • driver door unlock
    • liftgate unlock
For additional information, refer to Section 419-01A Anti - Theft - Active, Section 501-14A Handles, Locks, Latches and Mechanisms, and Section 501-14B Keyless Entry/Computer Operated Locks.

The CSM is in the passenger side kick panel I think.

Good luck

Jan 25, 2011 | 1999 Mercury Cougar

1 Answer

Central Locking


When you use your remote or insert your key in the Drivers Front door all the door locks should work at the same time by the door lock motors electrically. If you have to manually unlock the door because it will not lock or unlock by the lock motor, you need a door lock motor. The drivers and passengers front door can unlocked with the key manually. The rear doors you have to pull up the latch. If no doors unlock electrically with the remote or drivers door lock, intermittantly or all the time, you will need a Central Locking Electronic Control Module. You will hear the "beep" but no door locks will fire at all. If you have odd door locks not working intermittantly you need a new door lock motor for each door lock that malfunctions. You can hear of the door locks are working electrically. Yes, they are common problem. If you can hear the door lock working but the door still doesn't unlock you need to take the door panel off and lubricate the door latch assembly and work the lock, loosening it up. This is common as well.

May 30, 2009 | 1996 Saab 900

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

182 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peugeot Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Wahs Team

Level 2 Expert

205 Answers

yadayada
yadayada

Level 3 Expert

60960 Answers

Are you a Peugeot Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...